The ITE IT8xxx2 SHI host-command backend in subsys/mgmt/ec_host_cmd/backends/ec_host_cmd_backend_shi_ite.c arms the SPI peripheral before its receive context exists. shi_ite_init_registers() sets the state machine to SHI_STATE_READY_TO_RECV and calls irq_enable() while the device initializes at POST_KERNEL priority CONFIG_KERNEL_INIT_PRIORITY_DEFAULT (40), but data->rx_ctx and data->tx are only assigned later by shi_ite_backend_init(), which ec_host_cmd_init() invokes at CONFIG_EC_HOST_CMD_INIT_PRIORITY (default 80).
If the attached host processor starts a SPI transaction inside that window, the Rx-valid-length interrupt fires, shi_ite_int_handler() passes its state check and calls shi_ite_parse_header(), which stores the host-derived request length through the still-NULL data->rx_ctx. On the IT8xxx2 low addresses are not backed by RAM, and with CONFIG_NULL_POINTER_EXCEPTION_DETECTION_PMP the first bytes of the address space are explicitly made inaccessible, so the store raises a fatal access fault in interrupt context. The window widens further when CONFIG_EC_HOST_CMD_INITIALIZE_AT_BOOT is disabled and the application calls ec_host_cmd_init() itself.
The result is a kernel panic on the embedded controller: with Zephyr's default fatal handler the CPU halts, so the controller stops servicing host commands until a hardware reset. Because the trigger is traffic from the attached host processor -- an untrusted peer from the controller firmware's point of view -- software on that host can provoke the fault by forcing a controller reset and issuing transactions during the reboot, turning a recoverable reset into a persistent outage. Impact is limited to availability: the faulting address is fixed and not attacker-chosen, so no memory-corruption primitive follows.
The fix leaves the interface at SHI_STATE_DISABLED with the interrupt masked during device init, moves irq_enable() into shi_ite_backend_init() after the buffers are published, and makes shi_ite_int_handler() reject a NULL data->rx_ctx while write-clearing IT83XX_SPI_ISR and IT83XX_SPI_RX_VLISR so that an unexpected early interrupt cannot storm.
If the attached host processor starts a SPI transaction inside that window, the Rx-valid-length interrupt fires, shi_ite_int_handler() passes its state check and calls shi_ite_parse_header(), which stores the host-derived request length through the still-NULL data->rx_ctx. On the IT8xxx2 low addresses are not backed by RAM, and with CONFIG_NULL_POINTER_EXCEPTION_DETECTION_PMP the first bytes of the address space are explicitly made inaccessible, so the store raises a fatal access fault in interrupt context. The window widens further when CONFIG_EC_HOST_CMD_INITIALIZE_AT_BOOT is disabled and the application calls ec_host_cmd_init() itself.
The result is a kernel panic on the embedded controller: with Zephyr's default fatal handler the CPU halts, so the controller stops servicing host commands until a hardware reset. Because the trigger is traffic from the attached host processor -- an untrusted peer from the controller firmware's point of view -- software on that host can provoke the fault by forcing a controller reset and issuing transactions during the reboot, turning a recoverable reset into a persistent outage. Impact is limited to availability: the faulting address is fixed and not attacker-chosen, so no memory-corruption primitive follows.
The fix leaves the interface at SHI_STATE_DISABLED with the interrupt masked during device init, moves irq_enable() into shi_ite_backend_init() after the buffers are published, and makes shi_ite_int_handler() reject a NULL data->rx_ctx while write-clearing IT83XX_SPI_ISR and IT83XX_SPI_RX_VLISR so that an unexpected early interrupt cannot storm.
Metrics
Affected Vendors & Products
Advisories
No advisories yet.
Fixes
Solution
No solution given by the vendor.
Workaround
No workaround given by the vendor.
References
History
Mon, 16 Nov 2026 23:00:00 +0000
| Type | Values Removed | Values Added |
|---|---|---|
| First Time appeared |
Zephyrproject
Zephyrproject zephyr |
|
| Vendors & Products |
Zephyrproject
Zephyrproject zephyr |
Mon, 16 Nov 2026 21:30:00 +0000
| Type | Values Removed | Values Added |
|---|---|---|
| Description | The ITE IT8xxx2 SHI host-command backend in subsys/mgmt/ec_host_cmd/backends/ec_host_cmd_backend_shi_ite.c arms the SPI peripheral before its receive context exists. shi_ite_init_registers() sets the state machine to SHI_STATE_READY_TO_RECV and calls irq_enable() while the device initializes at POST_KERNEL priority CONFIG_KERNEL_INIT_PRIORITY_DEFAULT (40), but data->rx_ctx and data->tx are only assigned later by shi_ite_backend_init(), which ec_host_cmd_init() invokes at CONFIG_EC_HOST_CMD_INIT_PRIORITY (default 80). If the attached host processor starts a SPI transaction inside that window, the Rx-valid-length interrupt fires, shi_ite_int_handler() passes its state check and calls shi_ite_parse_header(), which stores the host-derived request length through the still-NULL data->rx_ctx. On the IT8xxx2 low addresses are not backed by RAM, and with CONFIG_NULL_POINTER_EXCEPTION_DETECTION_PMP the first bytes of the address space are explicitly made inaccessible, so the store raises a fatal access fault in interrupt context. The window widens further when CONFIG_EC_HOST_CMD_INITIALIZE_AT_BOOT is disabled and the application calls ec_host_cmd_init() itself. The result is a kernel panic on the embedded controller: with Zephyr's default fatal handler the CPU halts, so the controller stops servicing host commands until a hardware reset. Because the trigger is traffic from the attached host processor -- an untrusted peer from the controller firmware's point of view -- software on that host can provoke the fault by forcing a controller reset and issuing transactions during the reboot, turning a recoverable reset into a persistent outage. Impact is limited to availability: the faulting address is fixed and not attacker-chosen, so no memory-corruption primitive follows. The fix leaves the interface at SHI_STATE_DISABLED with the interrupt masked during device init, moves irq_enable() into shi_ite_backend_init() after the buffers are published, and makes shi_ite_int_handler() reject a NULL data->rx_ctx while write-clearing IT83XX_SPI_ISR and IT83XX_SPI_RX_VLISR so that an unexpected early interrupt cannot storm. | |
| Title | NULL pointer dereference in the ITE IT8xxx2 SHI host-command backend when a host transaction arrives before backend initialization | |
| Weaknesses | CWE-476 | |
| References |
| |
| Metrics |
cvssV3_1
|
Projects
Sign in to view the affected projects.
Status: PUBLISHED
Assigner: zephyr
Published:
Updated: 2026-11-16T21:19:17.897Z
Reserved: 2026-09-18T13:48:54.198Z
Link: CVE-2026-93669
No data.
Status : Awaiting Analysis
Published: 2026-11-16T22:18:26.577
Modified: 2026-11-16T22:18:26.683
Link: CVE-2026-93669
No data.
OpenCVE Enrichment
Updated: 2026-11-16T23:45:19Z
Weaknesses