The CC1200 sub-GHz IEEE 802.15.4 driver takes the PHY packet length from the first byte of the radio's RX FIFO in get_packet_length() and validates it in verify_rxfifo_validity() (drivers/ieee802154/ieee802154_cc1200.c). That validation only enforced a lower bound (pkt_len < 3); its second clause rejects a FIFO that holds more bytes than declared and therefore never bounds large values. Because the driver configures the radio for variable packet length with PKT_LEN = 0xFF, the length byte is an over-the-air value of 0-255 that reached net_pkt_rx_alloc_with_buffer() and the subsequent SPI burst read unclamped.
An unauthenticated attacker within radio range can transmit a frame that presents a length byte above the IEEE 802.15.4 maximum of 127 while the chip's 128-byte RX FIFO has not overflowed, so the driver's RX_FIFO_ERROR pre-check does not fire. Reaching this state depends on RF framing and timing, since the RX thread is driven off the PKT_SYNC_RXTX signal and may sample the FIFO before a packet is complete; no pairing, authentication, or user interaction is required.
With the default CONFIG_NET_BUF_FIXED_DATA_SIZE and CONFIG_NET_BUF_DATA_SIZE=128, an allocation larger than one fragment is satisfied by a chain of fragments, but read_rxfifo_content() performs a single SPI burst of pkt_len bytes into the first fragment's buf->data and then calls net_buf_add() with the same length. A length above 128 therefore writes up to 127 bytes past the end of a fragment in the contiguous rx_bufs pool and leaves a net_buf whose len exceeds its capacity. The overflowing bytes are FIFO-underflow output rather than attacker-chosen data, so the practical impact is network-buffer-pool corruption and crashes rather than a controlled write. Only builds that enable CONFIG_IEEE802154_CC1200 with an attached CC1200 radio are affected.
An unauthenticated attacker within radio range can transmit a frame that presents a length byte above the IEEE 802.15.4 maximum of 127 while the chip's 128-byte RX FIFO has not overflowed, so the driver's RX_FIFO_ERROR pre-check does not fire. Reaching this state depends on RF framing and timing, since the RX thread is driven off the PKT_SYNC_RXTX signal and may sample the FIFO before a packet is complete; no pairing, authentication, or user interaction is required.
With the default CONFIG_NET_BUF_FIXED_DATA_SIZE and CONFIG_NET_BUF_DATA_SIZE=128, an allocation larger than one fragment is satisfied by a chain of fragments, but read_rxfifo_content() performs a single SPI burst of pkt_len bytes into the first fragment's buf->data and then calls net_buf_add() with the same length. A length above 128 therefore writes up to 127 bytes past the end of a fragment in the contiguous rx_bufs pool and leaves a net_buf whose len exceeds its capacity. The overflowing bytes are FIFO-underflow output rather than attacker-chosen data, so the practical impact is network-buffer-pool corruption and crashes rather than a controlled write. Only builds that enable CONFIG_IEEE802154_CC1200 with an attached CC1200 radio are affected.
Metrics
Affected Vendors & Products
No data.
No data.
No data.
No data.
Advisories
No advisories yet.
Fixes
Solution
No solution given by the vendor.
Workaround
No workaround given by the vendor.
References
History
Wed, 14 Oct 2026 17:00:00 +0000
| Type | Values Removed | Values Added |
|---|---|---|
| Description | The CC1200 sub-GHz IEEE 802.15.4 driver takes the PHY packet length from the first byte of the radio's RX FIFO in get_packet_length() and validates it in verify_rxfifo_validity() (drivers/ieee802154/ieee802154_cc1200.c). That validation only enforced a lower bound (pkt_len < 3); its second clause rejects a FIFO that holds more bytes than declared and therefore never bounds large values. Because the driver configures the radio for variable packet length with PKT_LEN = 0xFF, the length byte is an over-the-air value of 0-255 that reached net_pkt_rx_alloc_with_buffer() and the subsequent SPI burst read unclamped. An unauthenticated attacker within radio range can transmit a frame that presents a length byte above the IEEE 802.15.4 maximum of 127 while the chip's 128-byte RX FIFO has not overflowed, so the driver's RX_FIFO_ERROR pre-check does not fire. Reaching this state depends on RF framing and timing, since the RX thread is driven off the PKT_SYNC_RXTX signal and may sample the FIFO before a packet is complete; no pairing, authentication, or user interaction is required. With the default CONFIG_NET_BUF_FIXED_DATA_SIZE and CONFIG_NET_BUF_DATA_SIZE=128, an allocation larger than one fragment is satisfied by a chain of fragments, but read_rxfifo_content() performs a single SPI burst of pkt_len bytes into the first fragment's buf->data and then calls net_buf_add() with the same length. A length above 128 therefore writes up to 127 bytes past the end of a fragment in the contiguous rx_bufs pool and leaves a net_buf whose len exceeds its capacity. The overflowing bytes are FIFO-underflow output rather than attacker-chosen data, so the practical impact is network-buffer-pool corruption and crashes rather than a controlled write. Only builds that enable CONFIG_IEEE802154_CC1200 with an attached CC1200 radio are affected. | |
| Title | Out-of-bounds write in the TI CC1200 IEEE 802.15.4 driver from an unvalidated radio-supplied packet length | |
| Weaknesses | CWE-787 | |
| References |
| |
| Metrics |
cvssV3_1
|
Projects
Sign in to view the affected projects.
MITRE
Status: PUBLISHED
Assigner: zephyr
Published:
Updated: 2026-10-14T16:46:01.701Z
Reserved: 2026-08-17T16:17:47.262Z
Link: CVE-2026-75084
Vulnrichment
No data.
NVD
Status : Received
Published: 2026-10-14T17:19:10.457
Modified: 2026-10-14T17:19:10.457
Link: CVE-2026-75084
Redhat
No data.
OpenCVE Enrichment
No data.
Weaknesses