| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
md: init bioset in mddev_init
IO operations may be needed before md_run(), such as updating metadata
after writing sysfs. Without bioset, this triggers a NULL pointer
dereference as below:
BUG: kernel NULL pointer dereference, address: 0000000000000020
Call Trace:
md_update_sb+0x658/0xe00
new_level_store+0xc5/0x120
md_attr_store+0xc9/0x1e0
sysfs_kf_write+0x6f/0xa0
kernfs_fop_write_iter+0x141/0x2a0
vfs_write+0x1fc/0x5a0
ksys_write+0x79/0x180
__x64_sys_write+0x1d/0x30
x64_sys_call+0x2818/0x2880
do_syscall_64+0xa9/0x580
entry_SYSCALL_64_after_hwframe+0x4b/0x53
Reproducer
```
mdadm -CR /dev/md0 -l1 -n2 /dev/sd[cd]
echo inactive > /sys/block/md0/md/array_state
echo 10 > /sys/block/md0/md/new_level
```
mddev_init() can only be called once per mddev, no need to test if bioset
has been initialized anymore. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qedi: Fix use after free bug in qedi_remove()
In qedi_probe() we call __qedi_probe() which initializes
&qedi->recovery_work with qedi_recovery_handler() and
&qedi->board_disable_work with qedi_board_disable_work().
When qedi_schedule_recovery_handler() is called, schedule_delayed_work()
will finally start the work.
In qedi_remove(), which is called to remove the driver, the following
sequence may be observed:
Fix this by finishing the work before cleanup in qedi_remove().
CPU0 CPU1
|qedi_recovery_handler
qedi_remove |
__qedi_remove |
iscsi_host_free |
scsi_host_put |
//free shost |
|iscsi_host_for_each_session
|//use qedi->shost
Cancel recovery_work and board_disable_work in __qedi_remove(). |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Do not let BPF test infra emit invalid GSO types to stack
Yinhao et al. reported that their fuzzer tool was able to trigger a
skb_warn_bad_offload() from netif_skb_features() -> gso_features_check().
When a BPF program - triggered via BPF test infra - pushes the packet
to the loopback device via bpf_clone_redirect() then mentioned offload
warning can be seen. GSO-related features are then rightfully disabled.
We get into this situation due to convert___skb_to_skb() setting
gso_segs and gso_size but not gso_type. Technically, it makes sense
that this warning triggers since the GSO properties are malformed due
to the gso_type. Potentially, the gso_type could be marked non-trustworthy
through setting it at least to SKB_GSO_DODGY without any other specific
assumptions, but that also feels wrong given we should not go further
into the GSO engine in the first place.
The checks were added in 121d57af308d ("gso: validate gso_type in GSO
handlers") because there were malicious (syzbot) senders that combine
a protocol with a non-matching gso_type. If we would want to drop such
packets, gso_features_check() currently only returns feature flags via
netif_skb_features(), so one location for potentially dropping such skbs
could be validate_xmit_unreadable_skb(), but then otoh it would be
an additional check in the fast-path for a very corner case. Given
bpf_clone_redirect() is the only place where BPF test infra could emit
such packets, lets reject them right there. |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid5: Remove unnecessary bio_put() in raid5_read_one_chunk()
When running chunk-sized reads on disks with badblocks duplicate bio
free/puts are observed:
=============================================================================
BUG bio-200 (Not tainted): Object already free
-----------------------------------------------------------------------------
Allocated in mempool_alloc_slab+0x17/0x20 age=3 cpu=2 pid=7504
__slab_alloc.constprop.0+0x5a/0xb0
kmem_cache_alloc+0x31e/0x330
mempool_alloc_slab+0x17/0x20
mempool_alloc+0x100/0x2b0
bio_alloc_bioset+0x181/0x460
do_mpage_readpage+0x776/0xd00
mpage_readahead+0x166/0x320
blkdev_readahead+0x15/0x20
read_pages+0x13f/0x5f0
page_cache_ra_unbounded+0x18d/0x220
force_page_cache_ra+0x181/0x1c0
page_cache_sync_ra+0x65/0xb0
filemap_get_pages+0x1df/0xaf0
filemap_read+0x1e1/0x700
blkdev_read_iter+0x1e5/0x330
vfs_read+0x42a/0x570
Freed in mempool_free_slab+0x17/0x20 age=3 cpu=2 pid=7504
kmem_cache_free+0x46d/0x490
mempool_free_slab+0x17/0x20
mempool_free+0x66/0x190
bio_free+0x78/0x90
bio_put+0x100/0x1a0
raid5_make_request+0x2259/0x2450
md_handle_request+0x402/0x600
md_submit_bio+0xd9/0x120
__submit_bio+0x11f/0x1b0
submit_bio_noacct_nocheck+0x204/0x480
submit_bio_noacct+0x32e/0xc70
submit_bio+0x98/0x1a0
mpage_readahead+0x250/0x320
blkdev_readahead+0x15/0x20
read_pages+0x13f/0x5f0
page_cache_ra_unbounded+0x18d/0x220
Slab 0xffffea000481b600 objects=21 used=0 fp=0xffff8881206d8940 flags=0x17ffffc0010201(locked|slab|head|node=0|zone=2|lastcpupid=0x1fffff)
CPU: 0 PID: 34525 Comm: kworker/u24:2 Not tainted 6.0.0-rc2-localyes-265166-gf11c5343fa3f #143
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.13.0-1ubuntu1.1 04/01/2014
Workqueue: raid5wq raid5_do_work
Call Trace:
<TASK>
dump_stack_lvl+0x5a/0x78
dump_stack+0x10/0x16
print_trailer+0x158/0x165
object_err+0x35/0x50
free_debug_processing.cold+0xb7/0xbe
__slab_free+0x1ae/0x330
kmem_cache_free+0x46d/0x490
mempool_free_slab+0x17/0x20
mempool_free+0x66/0x190
bio_free+0x78/0x90
bio_put+0x100/0x1a0
mpage_end_io+0x36/0x150
bio_endio+0x2fd/0x360
md_end_io_acct+0x7e/0x90
bio_endio+0x2fd/0x360
handle_failed_stripe+0x960/0xb80
handle_stripe+0x1348/0x3760
handle_active_stripes.constprop.0+0x72a/0xaf0
raid5_do_work+0x177/0x330
process_one_work+0x616/0xb20
worker_thread+0x2bd/0x6f0
kthread+0x179/0x1b0
ret_from_fork+0x22/0x30
</TASK>
The double free is caused by an unnecessary bio_put() in the
if(is_badblock(...)) error path in raid5_read_one_chunk().
The error path was moved ahead of bio_alloc_clone() in c82aa1b76787c
("md/raid5: move checking badblock before clone bio in
raid5_read_one_chunk"). The previous code checked and freed align_bio
which required a bio_put. After the move that is no longer needed as
raid_bio is returned to the control of the common io path which
performs its own endio resulting in a double free on bad device blocks. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/fbdev-generic: prohibit potential out-of-bounds access
The fbdev test of IGT may write after EOF, which lead to out-of-bound
access for drm drivers with fbdev-generic. For example, run fbdev test
on a x86+ast2400 platform, with 1680x1050 resolution, will cause the
linux kernel hang with the following call trace:
Oops: 0000 [#1] PREEMPT SMP PTI
[IGT] fbdev: starting subtest eof
Workqueue: events drm_fb_helper_damage_work [drm_kms_helper]
[IGT] fbdev: starting subtest nullptr
RIP: 0010:memcpy_erms+0xa/0x20
RSP: 0018:ffffa17d40167d98 EFLAGS: 00010246
RAX: ffffa17d4eb7fa80 RBX: ffffa17d40e0aa80 RCX: 00000000000014c0
RDX: 0000000000001a40 RSI: ffffa17d40e0b000 RDI: ffffa17d4eb80000
RBP: ffffa17d40167e20 R08: 0000000000000000 R09: ffff89522ecff8c0
R10: ffffa17d4e4c5000 R11: 0000000000000000 R12: ffffa17d4eb7fa80
R13: 0000000000001a40 R14: 000000000000041a R15: ffffa17d40167e30
FS: 0000000000000000(0000) GS:ffff895257380000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffa17d40e0b000 CR3: 00000001eaeca006 CR4: 00000000001706e0
Call Trace:
<TASK>
? drm_fbdev_generic_helper_fb_dirty+0x207/0x330 [drm_kms_helper]
drm_fb_helper_damage_work+0x8f/0x170 [drm_kms_helper]
process_one_work+0x21f/0x430
worker_thread+0x4e/0x3c0
? __pfx_worker_thread+0x10/0x10
kthread+0xf4/0x120
? __pfx_kthread+0x10/0x10
ret_from_fork+0x2c/0x50
</TASK>
CR2: ffffa17d40e0b000
---[ end trace 0000000000000000 ]---
The is because damage rectangles computed by
drm_fb_helper_memory_range_to_clip() function is not guaranteed to be
bound in the screen's active display area. Possible reasons are:
1) Buffers are allocated in the granularity of page size, for mmap system
call support. The shadow screen buffer consumed by fbdev emulation may
also choosed be page size aligned.
2) The DIV_ROUND_UP() used in drm_fb_helper_memory_range_to_clip()
will introduce off-by-one error.
For example, on a 16KB page size system, in order to store a 1920x1080
XRGB framebuffer, we need allocate 507 pages. Unfortunately, the size
1920*1080*4 can not be divided exactly by 16KB.
1920 * 1080 * 4 = 8294400 bytes
506 * 16 * 1024 = 8290304 bytes
507 * 16 * 1024 = 8306688 bytes
line_length = 1920*4 = 7680 bytes
507 * 16 * 1024 / 7680 = 1081.6
off / line_length = 507 * 16 * 1024 / 7680 = 1081
DIV_ROUND_UP(507 * 16 * 1024, 7680) will yeild 1082
memcpy_toio() typically issue the copy line by line, when copy the last
line, out-of-bound access will be happen. Because:
1082 * line_length = 1082 * 7680 = 8309760, and 8309760 > 8306688
Note that userspace may still write to the invisiable area if a larger
buffer than width x stride is exposed. But it is not a big issue as
long as there still have memory resolve the access if not drafting so
far.
- Also limit the y1 (Daniel)
- keep fix patch it to minimal (Daniel)
- screen_size is page size aligned because of it need mmap (Thomas)
- Adding fixes tag (Thomas) |
| In the Linux kernel, the following vulnerability has been resolved:
devlink: hold region lock when flushing snapshots
Netdevsim triggers a splat on reload, when it destroys regions
with snapshots pending:
WARNING: CPU: 1 PID: 787 at net/core/devlink.c:6291 devlink_region_snapshot_del+0x12e/0x140
CPU: 1 PID: 787 Comm: devlink Not tainted 6.1.0-07460-g7ae9888d6e1c #580
RIP: 0010:devlink_region_snapshot_del+0x12e/0x140
Call Trace:
<TASK>
devl_region_destroy+0x70/0x140
nsim_dev_reload_down+0x2f/0x60 [netdevsim]
devlink_reload+0x1f7/0x360
devlink_nl_cmd_reload+0x6ce/0x860
genl_family_rcv_msg_doit.isra.0+0x145/0x1c0
This is the locking assert in devlink_region_snapshot_del(),
we're supposed to be holding the region->snapshot_lock here. |
| In the Linux kernel, the following vulnerability has been resolved:
isdn: mISDN: hfcsusb: fix memory leak in hfcsusb_probe()
In hfcsusb_probe(), the memory allocated for ctrl_urb gets leaked when
setup_instance() fails with an error code. Fix that by freeing the urb
before freeing the hw structure. Also change the error paths to use the
goto ladder style.
Compile tested only. Issue found using a prototype static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rt2x00: Fix memory leak when handling surveys
When removing a rt2x00 device, its associated channel surveys
are not freed, causing a memory leak observable with kmemleak:
unreferenced object 0xffff9620f0881a00 (size 512):
comm "systemd-udevd", pid 2290, jiffies 4294906974 (age 33.768s)
hex dump (first 32 bytes):
70 44 12 00 00 00 00 00 92 8a 00 00 00 00 00 00 pD..............
00 00 00 00 00 00 00 00 ab 87 01 00 00 00 00 00 ................
backtrace:
[<ffffffffb0ed858b>] __kmalloc+0x4b/0x130
[<ffffffffc1b0f29b>] rt2800_probe_hw+0xc2b/0x1380 [rt2800lib]
[<ffffffffc1a9496e>] rt2800usb_probe_hw+0xe/0x60 [rt2800usb]
[<ffffffffc1ae491a>] rt2x00lib_probe_dev+0x21a/0x7d0 [rt2x00lib]
[<ffffffffc1b3b83e>] rt2x00usb_probe+0x1be/0x980 [rt2x00usb]
[<ffffffffc05981e2>] usb_probe_interface+0xe2/0x310 [usbcore]
[<ffffffffb13be2d5>] really_probe+0x1a5/0x410
[<ffffffffb13be5c8>] __driver_probe_device+0x78/0x180
[<ffffffffb13be6fe>] driver_probe_device+0x1e/0x90
[<ffffffffb13be972>] __driver_attach+0xd2/0x1c0
[<ffffffffb13bbc57>] bus_for_each_dev+0x77/0xd0
[<ffffffffb13bd2a2>] bus_add_driver+0x112/0x210
[<ffffffffb13bfc6c>] driver_register+0x5c/0x120
[<ffffffffc0596ae8>] usb_register_driver+0x88/0x150 [usbcore]
[<ffffffffb0c011c4>] do_one_initcall+0x44/0x220
[<ffffffffb0d6134c>] do_init_module+0x4c/0x220
Fix this by freeing the channel surveys on device removal.
Tested with a RT3070 based USB wireless adapter. |
| In the Linux kernel, the following vulnerability has been resolved:
power: supply: bq27xxx: Fix poll_interval handling and races on remove
Before this patch bq27xxx_battery_teardown() was setting poll_interval = 0
to avoid bq27xxx_battery_update() requeuing the delayed_work item.
There are 2 problems with this:
1. If the driver is unbound through sysfs, rather then the module being
rmmod-ed, this changes poll_interval unexpectedly
2. This is racy, after it being set poll_interval could be changed
before bq27xxx_battery_update() checks it through
/sys/module/bq27xxx_battery/parameters/poll_interval
Fix this by added a removed attribute to struct bq27xxx_device_info and
using that instead of setting poll_interval to 0.
There also is another poll_interval related race on remove(), writing
/sys/module/bq27xxx_battery/parameters/poll_interval will requeue
the delayed_work item for all devices on the bq27xxx_battery_devices
list and the device being removed was only removed from that list
after cancelling the delayed_work item.
Fix this by moving the removal from the bq27xxx_battery_devices list
to before cancelling the delayed_work item. |
| In the Linux kernel, the following vulnerability has been resolved:
driver: soc: xilinx: use _safe loop iterator to avoid a use after free
The hash_for_each_possible() loop dereferences "eve_data" to get the
next item on the list. However the loop frees eve_data so it leads to
a use after free. Use hash_for_each_possible_safe() instead. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath12k: Fix MSDU buffer types handling in RX error path
Currently, packets received on the REO exception ring from
unassociated peers are of MSDU buffer type, while the driver expects
link descriptor type packets. These packets are not parsed further due
to a return check on packet type in ath12k_hal_desc_reo_parse_err(),
but the associated skb is not freed. This may lead to kernel
crashes and buffer leaks.
Hence to fix, update the RX error handler to explicitly drop
MSDU buffer type packets received on the REO exception ring.
This prevents further processing of invalid packets and ensures
stability in the RX error handling path.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1 |
| In the Linux kernel, the following vulnerability has been resolved:
bnxt_en: fix memory leak in bnxt_nvm_test()
Free the kzalloc'ed buffer before returning in the success path. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: silence the warning when evicting inode with dioread_nolock
When evicting an inode with default dioread_nolock, it could be raced by
the unwritten extents converting kworker after writeback some new
allocated dirty blocks. It convert unwritten extents to written, the
extents could be merged to upper level and free extent blocks, so it
could mark the inode dirty again even this inode has been marked
I_FREEING. But the inode->i_io_list check and warning in
ext4_evict_inode() missing this corner case. Fortunately,
ext4_evict_inode() will wait all extents converting finished before this
check, so it will not lead to inode use-after-free problem, every thing
is OK besides this warning. The WARN_ON_ONCE was originally designed
for finding inode use-after-free issues in advance, but if we add
current dioread_nolock case in, it will become not quite useful, so fix
this warning by just remove this check.
======
WARNING: CPU: 7 PID: 1092 at fs/ext4/inode.c:227
ext4_evict_inode+0x875/0xc60
...
RIP: 0010:ext4_evict_inode+0x875/0xc60
...
Call Trace:
<TASK>
evict+0x11c/0x2b0
iput+0x236/0x3a0
do_unlinkat+0x1b4/0x490
__x64_sys_unlinkat+0x4c/0xb0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x46/0xb0
RIP: 0033:0x7fa933c1115b
======
rm kworker
ext4_end_io_end()
vfs_unlink()
ext4_unlink()
ext4_convert_unwritten_io_end_vec()
ext4_convert_unwritten_extents()
ext4_map_blocks()
ext4_ext_map_blocks()
ext4_ext_try_to_merge_up()
__mark_inode_dirty()
check !I_FREEING
locked_inode_to_wb_and_lock_list()
iput()
iput_final()
evict()
ext4_evict_inode()
truncate_inode_pages_final() //wait release io_end
inode_io_list_move_locked()
ext4_release_io_end()
trigger WARN_ON_ONCE() |
| In the Linux kernel, the following vulnerability has been resolved:
rcu: dump vmalloc memory info safely
Currently, for double invoke call_rcu(), will dump rcu_head objects memory
info, if the objects is not allocated from the slab allocator, the
vmalloc_dump_obj() will be invoke and the vmap_area_lock spinlock need to
be held, since the call_rcu() can be invoked in interrupt context,
therefore, there is a possibility of spinlock deadlock scenarios.
And in Preempt-RT kernel, the rcutorture test also trigger the following
lockdep warning:
BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48
in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 1, name: swapper/0
preempt_count: 1, expected: 0
RCU nest depth: 1, expected: 1
3 locks held by swapper/0/1:
#0: ffffffffb534ee80 (fullstop_mutex){+.+.}-{4:4}, at: torture_init_begin+0x24/0xa0
#1: ffffffffb5307940 (rcu_read_lock){....}-{1:3}, at: rcu_torture_init+0x1ec7/0x2370
#2: ffffffffb536af40 (vmap_area_lock){+.+.}-{3:3}, at: find_vmap_area+0x1f/0x70
irq event stamp: 565512
hardirqs last enabled at (565511): [<ffffffffb379b138>] __call_rcu_common+0x218/0x940
hardirqs last disabled at (565512): [<ffffffffb5804262>] rcu_torture_init+0x20b2/0x2370
softirqs last enabled at (399112): [<ffffffffb36b2586>] __local_bh_enable_ip+0x126/0x170
softirqs last disabled at (399106): [<ffffffffb43fef59>] inet_register_protosw+0x9/0x1d0
Preemption disabled at:
[<ffffffffb58040c3>] rcu_torture_init+0x1f13/0x2370
CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W 6.5.0-rc4-rt2-yocto-preempt-rt+ #15
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.2-0-gea1b7a073390-prebuilt.qemu.org 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x68/0xb0
dump_stack+0x14/0x20
__might_resched+0x1aa/0x280
? __pfx_rcu_torture_err_cb+0x10/0x10
rt_spin_lock+0x53/0x130
? find_vmap_area+0x1f/0x70
find_vmap_area+0x1f/0x70
vmalloc_dump_obj+0x20/0x60
mem_dump_obj+0x22/0x90
__call_rcu_common+0x5bf/0x940
? debug_smp_processor_id+0x1b/0x30
call_rcu_hurry+0x14/0x20
rcu_torture_init+0x1f82/0x2370
? __pfx_rcu_torture_leak_cb+0x10/0x10
? __pfx_rcu_torture_leak_cb+0x10/0x10
? __pfx_rcu_torture_init+0x10/0x10
do_one_initcall+0x6c/0x300
? debug_smp_processor_id+0x1b/0x30
kernel_init_freeable+0x2b9/0x540
? __pfx_kernel_init+0x10/0x10
kernel_init+0x1f/0x150
ret_from_fork+0x40/0x50
? __pfx_kernel_init+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
The previous patch fixes this by using the deadlock-safe best-effort
version of find_vm_area. However, in case of failure print the fact that
the pointer was a vmalloc pointer so that we print at least something. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/client: Fix memory leak in drm_client_target_cloned
dmt_mode is allocated and never freed in this function.
It was found with the ast driver, but most drivers using generic fbdev
setup are probably affected.
This fixes the following kmemleak report:
backtrace:
[<00000000b391296d>] drm_mode_duplicate+0x45/0x220 [drm]
[<00000000e45bb5b3>] drm_client_target_cloned.constprop.0+0x27b/0x480 [drm]
[<00000000ed2d3a37>] drm_client_modeset_probe+0x6bd/0xf50 [drm]
[<0000000010e5cc9d>] __drm_fb_helper_initial_config_and_unlock+0xb4/0x2c0 [drm_kms_helper]
[<00000000909f82ca>] drm_fbdev_client_hotplug+0x2bc/0x4d0 [drm_kms_helper]
[<00000000063a69aa>] drm_client_register+0x169/0x240 [drm]
[<00000000a8c61525>] ast_pci_probe+0x142/0x190 [ast]
[<00000000987f19bb>] local_pci_probe+0xdc/0x180
[<000000004fca231b>] work_for_cpu_fn+0x4e/0xa0
[<0000000000b85301>] process_one_work+0x8b7/0x1540
[<000000003375b17c>] worker_thread+0x70a/0xed0
[<00000000b0d43cd9>] kthread+0x29f/0x340
[<000000008d770833>] ret_from_fork+0x1f/0x30
unreferenced object 0xff11000333089a00 (size 128): |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7921e: fix rmmod crash in driver reload test
In insmod/rmmod stress test, the following crash dump shows up immediately.
The problem is caused by missing mt76_dev in mt7921_pci_remove(). We
should make sure the drvdata is ready before probe() finished.
[168.862789] ==================================================================
[168.862797] BUG: KASAN: user-memory-access in try_to_grab_pending+0x59/0x480
[168.862805] Write of size 8 at addr 0000000000006df0 by task rmmod/5361
[168.862812] CPU: 7 PID: 5361 Comm: rmmod Tainted: G OE 5.19.0-rc6 #1
[168.862816] Hardware name: Intel(R) Client Systems NUC8i7BEH/NUC8BEB, 05/04/2020
[168.862820] Call Trace:
[168.862822] <TASK>
[168.862825] dump_stack_lvl+0x49/0x63
[168.862832] print_report.cold+0x493/0x6b7
[168.862845] kasan_report+0xa7/0x120
[168.862857] kasan_check_range+0x163/0x200
[168.862861] __kasan_check_write+0x14/0x20
[168.862866] try_to_grab_pending+0x59/0x480
[168.862870] __cancel_work_timer+0xbb/0x340
[168.862898] cancel_work_sync+0x10/0x20
[168.862902] mt7921_pci_remove+0x61/0x1c0 [mt7921e]
[168.862909] pci_device_remove+0xa3/0x1d0
[168.862914] device_remove+0xc4/0x170
[168.862920] device_release_driver_internal+0x163/0x300
[168.862925] driver_detach+0xc7/0x1a0
[168.862930] bus_remove_driver+0xeb/0x2d0
[168.862935] driver_unregister+0x71/0xb0
[168.862939] pci_unregister_driver+0x30/0x230
[168.862944] mt7921_pci_driver_exit+0x10/0x1b [mt7921e]
[168.862949] __x64_sys_delete_module+0x2f9/0x4b0
[168.862968] do_syscall_64+0x38/0x90
[168.862973] entry_SYSCALL_64_after_hwframe+0x63/0xcd
Test steps:
1. insmode
2. do not ifup
3. rmmod quickly (within 1 second) |
| In the Linux kernel, the following vulnerability has been resolved:
iommufd: Set end correctly when doing batch carry
Even though the test suite covers this it somehow became obscured that
this wasn't working.
The test iommufd_ioas.mock_domain.access_domain_destory would blow up
rarely.
end should be set to 1 because this just pushed an item, the carry, to the
pfns list.
Sometimes the test would blow up with:
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] SMP
CPU: 5 PID: 584 Comm: iommufd Not tainted 6.5.0-rc1-dirty #1236
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
RIP: 0010:batch_unpin+0xa2/0x100 [iommufd]
Code: 17 48 81 fe ff ff 07 00 77 70 48 8b 15 b7 be 97 e2 48 85 d2 74 14 48 8b 14 fa 48 85 d2 74 0b 40 0f b6 f6 48 c1 e6 04 48 01 f2 <48> 8b 3a 48 c1 e0 06 89 ca 48 89 de 48 83 e7 f0 48 01 c7 e8 96 dc
RSP: 0018:ffffc90001677a58 EFLAGS: 00010246
RAX: 00007f7e2646f000 RBX: 0000000000000000 RCX: 0000000000000001
RDX: 0000000000000000 RSI: 00000000fefc4c8d RDI: 0000000000fefc4c
RBP: ffffc90001677a80 R08: 0000000000000048 R09: 0000000000000200
R10: 0000000000030b98 R11: ffffffff81f3bb40 R12: 0000000000000001
R13: ffff888101f75800 R14: ffffc90001677ad0 R15: 00000000000001fe
FS: 00007f9323679740(0000) GS:ffff8881ba540000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 0000000105ede003 CR4: 00000000003706a0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
? show_regs+0x5c/0x70
? __die+0x1f/0x60
? page_fault_oops+0x15d/0x440
? lock_release+0xbc/0x240
? exc_page_fault+0x4a4/0x970
? asm_exc_page_fault+0x27/0x30
? batch_unpin+0xa2/0x100 [iommufd]
? batch_unpin+0xba/0x100 [iommufd]
__iopt_area_unfill_domain+0x198/0x430 [iommufd]
? __mutex_lock+0x8c/0xb80
? __mutex_lock+0x6aa/0xb80
? xa_erase+0x28/0x30
? iopt_table_remove_domain+0x162/0x320 [iommufd]
? lock_release+0xbc/0x240
iopt_area_unfill_domain+0xd/0x10 [iommufd]
iopt_table_remove_domain+0x195/0x320 [iommufd]
iommufd_hw_pagetable_destroy+0xb3/0x110 [iommufd]
iommufd_object_destroy_user+0x8e/0xf0 [iommufd]
iommufd_device_detach+0xc5/0x140 [iommufd]
iommufd_selftest_destroy+0x1f/0x70 [iommufd]
iommufd_object_destroy_user+0x8e/0xf0 [iommufd]
iommufd_destroy+0x3a/0x50 [iommufd]
iommufd_fops_ioctl+0xfb/0x170 [iommufd]
__x64_sys_ioctl+0x40d/0x9a0
do_syscall_64+0x3c/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0 |
| In the Linux kernel, the following vulnerability has been resolved:
rpmsg: glink: Add check for kstrdup
Add check for the return value of kstrdup() and return the error
if it fails in order to avoid NULL pointer dereference. |
| In the Linux kernel, the following vulnerability has been resolved:
nfp: clean mc addresses in application firmware when closing port
When moving devices from one namespace to another, mc addresses are
cleaned in software while not removed from application firmware. Thus
the mc addresses are remained and will cause resource leak.
Now use `__dev_mc_unsync` to clean mc addresses when closing port. |
| In the Linux kernel, the following vulnerability has been resolved:
igb: clean up in all error paths when enabling SR-IOV
After commit 50f303496d92 ("igb: Enable SR-IOV after reinit"), removing
the igb module could hang or crash (depending on the machine) when the
module has been loaded with the max_vfs parameter set to some value != 0.
In case of one test machine with a dual port 82580, this hang occurred:
[ 232.480687] igb 0000:41:00.1: removed PHC on enp65s0f1
[ 233.093257] igb 0000:41:00.1: IOV Disabled
[ 233.329969] pcieport 0000:40:01.0: AER: Multiple Uncorrected (Non-Fatal) err0
[ 233.340302] igb 0000:41:00.0: PCIe Bus Error: severity=Uncorrected (Non-Fata)
[ 233.352248] igb 0000:41:00.0: device [8086:1516] error status/mask=00100000
[ 233.361088] igb 0000:41:00.0: [20] UnsupReq (First)
[ 233.368183] igb 0000:41:00.0: AER: TLP Header: 40000001 0000040f cdbfc00c c
[ 233.376846] igb 0000:41:00.1: PCIe Bus Error: severity=Uncorrected (Non-Fata)
[ 233.388779] igb 0000:41:00.1: device [8086:1516] error status/mask=00100000
[ 233.397629] igb 0000:41:00.1: [20] UnsupReq (First)
[ 233.404736] igb 0000:41:00.1: AER: TLP Header: 40000001 0000040f cdbfc00c c
[ 233.538214] pci 0000:41:00.1: AER: can't recover (no error_detected callback)
[ 233.538401] igb 0000:41:00.0: removed PHC on enp65s0f0
[ 233.546197] pcieport 0000:40:01.0: AER: device recovery failed
[ 234.157244] igb 0000:41:00.0: IOV Disabled
[ 371.619705] INFO: task irq/35-aerdrv:257 blocked for more than 122 seconds.
[ 371.627489] Not tainted 6.4.0-dirty #2
[ 371.632257] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this.
[ 371.641000] task:irq/35-aerdrv state:D stack:0 pid:257 ppid:2 f0
[ 371.650330] Call Trace:
[ 371.653061] <TASK>
[ 371.655407] __schedule+0x20e/0x660
[ 371.659313] schedule+0x5a/0xd0
[ 371.662824] schedule_preempt_disabled+0x11/0x20
[ 371.667983] __mutex_lock.constprop.0+0x372/0x6c0
[ 371.673237] ? __pfx_aer_root_reset+0x10/0x10
[ 371.678105] report_error_detected+0x25/0x1c0
[ 371.682974] ? __pfx_report_normal_detected+0x10/0x10
[ 371.688618] pci_walk_bus+0x72/0x90
[ 371.692519] pcie_do_recovery+0xb2/0x330
[ 371.696899] aer_process_err_devices+0x117/0x170
[ 371.702055] aer_isr+0x1c0/0x1e0
[ 371.705661] ? __set_cpus_allowed_ptr+0x54/0xa0
[ 371.710723] ? __pfx_irq_thread_fn+0x10/0x10
[ 371.715496] irq_thread_fn+0x20/0x60
[ 371.719491] irq_thread+0xe6/0x1b0
[ 371.723291] ? __pfx_irq_thread_dtor+0x10/0x10
[ 371.728255] ? __pfx_irq_thread+0x10/0x10
[ 371.732731] kthread+0xe2/0x110
[ 371.736243] ? __pfx_kthread+0x10/0x10
[ 371.740430] ret_from_fork+0x2c/0x50
[ 371.744428] </TASK>
The reproducer was a simple script:
#!/bin/sh
for i in `seq 1 5`; do
modprobe -rv igb
modprobe -v igb max_vfs=1
sleep 1
modprobe -rv igb
done
It turned out that this could only be reproduce on 82580 (quad and
dual-port), but not on 82576, i350 and i210. Further debugging showed
that igb_enable_sriov()'s call to pci_enable_sriov() is failing, because
dev->is_physfn is 0 on 82580.
Prior to commit 50f303496d92 ("igb: Enable SR-IOV after reinit"),
igb_enable_sriov() jumped into the "err_out" cleanup branch. After this
commit it only returned the error code.
So the cleanup didn't take place, and the incorrect VF setup in the
igb_adapter structure fooled the igb driver into assuming that VFs have
been set up where no VF actually existed.
Fix this problem by cleaning up again if pci_enable_sriov() fails. |
