| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
usb: xhci: Fix sleep in atomic context in xhci_free_streams()
When a USB device with active stream endpoints is disconnected,
xhci_free_streams() is called from the hub_event workqueue to
free the stream resources. It calls xhci_free_stream_info()
while holding xhci->lock with irqs disabled.
xhci_free_stream_info() invokes xhci_free_stream_ctx(), which
calls dma_free_coherent() for large stream context arrays.
dma_free_coherent() can sleep (e.g. via vunmap), triggering
a BUG when called from atomic context.
Call trace:
dma_free_attrs+0x174/0x220
xhci_free_stream_info+0xd0/0x11c
xhci_free_streams+0x278/0x37c
usb_free_streams+0x98/0xc0
usb_unbind_interface+0x1b8/0x2f8
device_release_driver_internal+0x1d4/0x2cc
device_release_driver+0x18/0x28
bus_remove_device+0x160/0x1a4
device_del+0x1ec/0x350
usb_disable_device+0x98/0x214
usb_disconnect+0xf0/0x35c
hub_event+0xab4/0x19ec
process_one_work+0x278/0x63c
Fix this by saving the stream_info pointers and clearing the
ep references under the lock, then calling xhci_free_stream_info()
outside the lock where sleeping is allowed. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: bridge: fix stale prevhdr pointer in br_ip6_fragment()
br_ip6_fragment() gets prevhdr, a pointer into the skb head, from
ip6_find_1stfragopt(), then calls skb_checksum_help(). For a cloned skb
skb_checksum_help() reallocates the head via pskb_expand_head(), leaving
prevhdr dangling. It is later dereferenced in ip6_frag_next(), causing a
use-after-free write.
Save prevhdr's offset before skb_checksum_help() and recompute it after,
like commit ef0efcd3bd3f ("ipv6: Fix dangling pointer when ipv6
fragment").
BUG: KASAN: slab-use-after-free in ip6_frag_next (net/ipv6/ip6_output.c:857)
Write of size 1 at addr ffff888013ff5016 by task exploit/141
Call Trace:
...
kasan_report (mm/kasan/report.c:595)
ip6_frag_next (net/ipv6/ip6_output.c:857)
br_ip6_fragment (net/ipv6/netfilter.c:212)
nf_ct_bridge_post (net/bridge/netfilter/nf_conntrack_bridge.c:407)
nf_hook_slow (net/netfilter/core.c:619)
br_forward_finish (net/bridge/br_forward.c:66)
__br_forward (net/bridge/br_forward.c:115)
maybe_deliver (net/bridge/br_forward.c:191)
br_flood (net/bridge/br_forward.c:245)
br_handle_frame_finish (net/bridge/br_input.c:229)
br_handle_frame (net/bridge/br_input.c:442)
...
packet_sendmsg (net/packet/af_packet.c:3114)
...
do_syscall_64 (arch/x86/entry/syscall_64.c:94)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121)
Kernel panic - not syncing: Fatal exception in interrupt |
| In the Linux kernel, the following vulnerability has been resolved:
usb: dwc3: fix dwc3_readl() and dwc3_writel() calls in dwc3_ulpi_setup()
The dwc3_ulpi_setup() calls the register read and write calls with
dwc3->regs when both these calls take the dwc3 structure directly.
Chnage these two calls to fix the following sparse warning, and
possibly a nasty bug in the dwc3_ulpi_setup() code:
drivers/usb/dwc3/core.c:796:45: warning: incorrect type in argument 1 (different address spaces)
drivers/usb/dwc3/core.c:796:45: expected struct dwc3 *dwc
drivers/usb/dwc3/core.c:796:45: got void [noderef] __iomem *regs
drivers/usb/dwc3/core.c:798:40: warning: incorrect type in argument 1 (different address spaces)
drivers/usb/dwc3/core.c:798:40: expected struct dwc3 *dwc
drivers/usb/dwc3/core.c:798:40: got void [noderef] __iomem *regs |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Reject fragmented frames in devmap
Devmap broadcast redirects clone the packet for all but the last
destination.
For native XDP, that clone path copies only the linear xdp_frame data,
while fragmented frames keep skb_shared_info in tailroom outside the
linear area. Cloning such a frame leaves XDP_FLAGS_HAS_FRAGS set but
without valid frag metadata, and the later free path can interpret
uninitialized tail data as skb_shared_info, leading to an out-of-bounds
access during frame return.
Reject fragmented native XDP frames in dev_map_enqueue_clone().
Add the same restriction to the generic XDP clone path in
dev_map_redirect_clone(). Generic XDP represents fragmented packets as
nonlinear skbs, and rejecting them here keeps clone-based broadcast
support aligned between native and generic XDP. |
| In the Linux kernel, the following vulnerability has been resolved:
cpufreq: qcom-cpufreq-hw: Fix possible double free
qcom_cpufreq.data is allocated with devm_kzalloc() in probe() as an
array of per-domain data. qcom_cpufreq_hw_cpu_init() stores a pointer to
one element of this array in policy->driver_data.
qcom_cpufreq_hw_cpu_exit() currently calls kfree() on policy->driver_data.
This is not valid because the memory is devm-managed. For the first
domain, this can free the devm-managed allocation while the devres entry
is still active, leading to a possible double free when the platform
device is later detached. For other domains, the pointer may refer to an
element inside the array rather than the allocation base.
Remove the kfree(data) call and let devres release qcom_cpufreq.data.
This issue was found by a static analysis tool I am developing. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix double-free in SMB2_ioctl() replay
A response-bearing attempt can return a replayable error and free its
response buffer. If SMB2_ioctl_init() fails before the next send, cleanup
retains the previous buffer type and frees that response again.
Reset response bookkeeping before each attempt to prevent the stale free. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix query_info() replay double-free
A response-bearing attempt can return a replayable error and free its
response buffer. If SMB2_query_info_init() fails before the next send,
cleanup retains the previous buffer type and frees that response again.
Reset response bookkeeping before each attempt to prevent the stale free. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: track the connection owning a byte-range lock
SMB2_LOCK adds each granted byte-range lock to both the file lock list
and the lock list of the connection which handled the request. The
final close and durable handle paths, however, remove the connection
list entry while holding fp->conn->llist_lock.
With SMB3 multichannel, the connection handling the LOCK request can be
different from the connection which opened the file. The entry can
therefore be removed under a different spinlock from the one protecting
the list it belongs to. A concurrent traversal can then access freed
struct ksmbd_lock and struct file_lock objects.
Record the connection owning each lock's clist entry and hold a
reference to it while the entry is linked. Use that connection and its
llist_lock for unlock, rollback, close, and durable preserve. Durable
reconnect assigns the new connection as the owner when publishing the
locks again. |
| In the Linux kernel, the following vulnerability has been resolved:
io_uring/io-wq: re-check IO_WQ_BIT_EXIT for each linked work item
commit 10dc95939817 ("io_uring/io-wq: check IO_WQ_BIT_EXIT inside work
run loop") fixed the obvious case where io_worker_handle_work() took one
exit-bit snapshot before draining pending work, but the fix stops one
level too early.
io_worker_handle_work() now re-checks IO_WQ_BIT_EXIT in its outer work
run loop, yet it still snapshots that bit once before processing a whole
dependent linked-work chain. If io_wq_exit_start() sets IO_WQ_BIT_EXIT
after the first linked item has started, the remaining linked items can
still reuse stale do_kill = false, skip IO_WQ_WORK_CANCEL, and continue
running after exit has begun.
Move the check further inside, so it covers linked items too. Note: this
is a syzbot special as it loves setting up tons of slow linked work on
weird devices like msr that take forever to read, and immediately close
the ring. Exit then takes a long time. |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: altera: Fix resource leaks on probe failure
The chained IRQ handler is set during probe, but is only removed during the
driver remove(). If pci_host_probe() fails, the handler and INTx IRQ
domain remain set even though the devm-managed host bridge storage
containing struct altera_pcie will be released, leaving the handler with
a stale data pointer.
Interrupts are also enabled before pci_host_probe() is called. If probe
fails after that point, the controller interrupt source should be disabled
before the chained handler and INTx domain are removed.
So set the chained handler only after the INTx domain has been created.
Disable controller interrupts during IRQ teardown, and tear the IRQ setup
down if pci_host_probe() fails.
[mani: commit log] |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: avoid kobject path lookup in DualSense match
The DualSense jack-detection input handler verifies that a matching input
device belongs to the same physical controller by building kobject path
strings for both the input device and the USB audio device, then comparing
the path prefix.
This was observed when a weak physical connection caused the controller
to rapidly disconnect and reconnect. During that repeated hotplug,
snd_dualsense_ih_match() can run while the controller's USB device is
being disconnected. kobject_get_path() walks ancestor kobjects and
dereferences their names; if the USB device kobject name is no longer
valid, this can fault in strlen():
RIP: 0010:strlen+0x10/0x30
Call Trace:
kobject_get_path+0x34/0x150
snd_dualsense_ih_match+0x49/0xd0 [snd_usb_audio]
input_register_device+0x566/0x6a0
ps_probe+0xb89/0x1590 [hid_playstation]
The same ownership check can be done without building kobject path
strings. The input device is parented below the HID device, USB interface
and USB device, so walking the input device parent chain and comparing
against the mixer USB device preserves the check without dereferencing
kobject names during disconnect. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: validate STALE_COOKIE cause length before reading staleness
When an ERROR chunk with a STALE_COOKIE cause is received in the
COOKIE_ECHOED state, sctp_sf_do_5_2_6_stale() reads the 4-byte Measure
of Staleness that follows the cause header:
err = (struct sctp_errhdr *)(chunk->skb->data);
stale = ntohl(*(__be32 *)((u8 *)err + sizeof(*err)));
err is the first cause in the chunk, not the STALE_COOKIE cause that
caused the dispatch, and nothing guarantees the staleness field is
present. sctp_walk_errors() only requires a cause to be as long as the
4-byte header, so for a STALE_COOKIE cause of length 4 the read runs
past the cause, and for a minimal ERROR chunk past skb->tail. The value
is echoed to the peer in the Cookie Preservative of the reply INIT,
leaking uninitialized memory.
sctp_sf_cookie_echoed_err() already walks to the STALE_COOKIE cause, so
check its length there and pass it to sctp_sf_do_5_2_6_stale(), which
reads that cause instead of the first one. A STALE_COOKIE cause too
short to hold the staleness field is discarded.
The read is reachable by any peer that can drive an association into
COOKIE_ECHOED, including an unprivileged process using a raw SCTP socket
in a user and network namespace. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: ims-pcu - fix heap-buffer-overflow in ims_pcu_process_data()
The `ims_pcu_process_data()` processes incoming URB data byte by byte.
However, it fails to check if the `read_pos` index exceeds
IMS_PCU_BUF_SIZE.
If a malicious USB device sends a packet larger than IMS_PCU_BUF_SIZE,
`read_pos` will increment indefinitely. Moreover, since `read_pos` is
located immediately after `read_buf`, the attacker can overwrite
`read_pos` itself to arbitrarily control the index.
This manipulated `read_pos` is subsequently used in
`ims_pcu_handle_response()` to copy data into `cmd_buf`, leading to a
heap buffer overflow.
Specifically, an attacker can overwrite the `cmd_done.wait.head` located
at offset 136 relative to `cmd_buf` in the `ims_pcu_handle_response()`.
Consequently, when the driver calls `complete(&pcu->cmd_done)`, it
triggers a control flow hijack by using the manipulated pointer.
Fix this by adding a bounds check for `read_pos` before writing to
`read_buf`. If the packet is too long, discard it, log a warning,
and reset the parser state.
[dtor: factor out resetting packet state, reset checksum as well] |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: do not free data reservation in fallback from inline due to -ENOSPC
If we fail to create an inline extent due to -ENOSPC, we will attempt to
go through the normal COW path, reserve an extent, create an ordered
extent, etc. However we were always freeing the reserved qgroup data,
which is wrong since we will use data. Fix this by freeing the reserved
qgroup data in __cow_file_range_inline() only if we are not doing the
fallback (ret is <= 0). |
| Use after free in Ozone in Google Chrome on Linux prior to 150.0.7871.128 allowed a remote attacker who convinced a user to engage in specific UI gestures to potentially exploit heap corruption via a crafted HTML page. (Chromium security severity: High) |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: codecs: simple-mux: Fix enum control bounds check
simple_mux_control_put() rejects values greater than e->items, but
enum control values are zero based. For the two-entry mux used by this
driver, valid values are 0 and 1, so value 2 must be rejected as well.
Accepting e->items can store an invalid mux state, pass it to the GPIO
setter, and pass it on to the DAPM mux update path where it is used as
an index into the enum text array.
Use the same >= e->items check used by the ASoC enum helpers. |
| In the Linux kernel, the following vulnerability has been resolved:
drivers/base/memory: set mem->altmap after successful device registration
If __add_memory_block() fails at xa_store() (under memory pressure for
example), device_unregister() is called, which eventually triggers
memory_block_release() with mem->altmap still set, causing a
WARN_ON(mem->altmap). This was triggered by modifying virtio-mem driver.
Fix this by delaying the assignment of mem->altmap until after
__add_memory_block() has succeeded. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: ccp - Do not initialize SNP for ioctl(SNP_VLEK_LOAD)
Sashiko notes:
> if SEV initialization fails and KVM is actively running normal VMs, could a
> userspace process trigger this code path via /dev/sev ioctls (e.g.,
> SEV_PDH_GEN) and zero out MSR_VM_HSAVE_PA globally? Would the next VMRUN
> execution for an active VM trigger a general protection fault and crash the
> host?
The SEV firmware docs for SNP_VLEK_LOAD note:
> On SNP_SHUTDOWN, the VLEK is deleted.
That is, the initialization/shutdown wrapper here is pointless, because the
firmware immediately throws away the key anyway. Instead, refuse to do
anything if SNP has not been previously initialized.
This is an ABI break: before, this was a no-op and almost certainly a
mistake by userspace, and now it returns -ENODEV. ABI compatibility could be
maintained here by simply returning 0 in the check instead. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: loongson - Remove broken and unused loongson-rng
The loongson-rng rng_alg has several vulnerabilities, including not
providing forward security, and a use-after-free bug due to the use of
wait_for_completion_interruptible().
Meanwhile, the rng_alg framework doesn't really have any purpose in the
first place other than to access the software algorithms crypto/drbg.c
and crypto/jitterentropy.c. Hardware-specific rng_algs have no
in-kernel user, and unlike hwrng there's no feed into the actual Linux
RNG. As such, there's really no point to this code. There are of
course other rng_alg drivers that are similarly unused, but they're
similarly in the process of being phased out, e.g.
https://lore.kernel.org/r/[email protected] and
https://lore.kernel.org/r/[email protected]
Given that, there's no point in fixing forward these vulnerabilities,
and it makes much more sense to simply roll back the addition of this
driver. If this platform provides TRNG (not PRNG) functionality, it
could make sense to add a hwrng driver, but it would be quite different. |
| In the Linux kernel, the following vulnerability has been resolved:
nvmet-auth: validate reply message payload bounds against transfer length
nvmet_auth_reply() accesses the variable-length rval[] array using
attacker-controlled hl (hash length) and dhvlen (DH value length) fields
without verifying they fit within the allocated buffer of tl bytes.
A malicious NVMe-oF initiator can craft a DHCHAP_REPLY message with a
small transfer length but large hl/dhvlen values, causing out-of-bounds
heap reads when the target processes the DH public key (rval + 2*hl) or
performs the host response memcmp.
With DH authentication configured, the OOB pointer is passed directly to
sg_init_one() and read by crypto_kpp_compute_shared_secret(), reaching
up to 526 bytes past the buffer. This is exploitable pre-authentication.
Add bounds validation ensuring sizeof(*data) + 2*hl + dhvlen <= tl before
any access to the variable-length fields.
Discovered by Atuin - Automated Vulnerability Discovery Engine. |
