| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
nvmem: Fix shift-out-of-bound (UBSAN) with byte size cells
If a cell has 'nbits' equal to a multiple of BITS_PER_BYTE the logic
*p &= GENMASK((cell->nbits%BITS_PER_BYTE) - 1, 0);
will become undefined behavior because nbits modulo BITS_PER_BYTE is 0, and we
subtract one from that making a large number that is then shifted more than the
number of bits that fit into an unsigned long.
UBSAN reports this problem:
UBSAN: shift-out-of-bounds in drivers/nvmem/core.c:1386:8
shift exponent 64 is too large for 64-bit type 'unsigned long'
CPU: 6 PID: 7 Comm: kworker/u16:0 Not tainted 5.15.0-rc3+ #9
Hardware name: Google Lazor (rev3+) with KB Backlight (DT)
Workqueue: events_unbound deferred_probe_work_func
Call trace:
dump_backtrace+0x0/0x170
show_stack+0x24/0x30
dump_stack_lvl+0x64/0x7c
dump_stack+0x18/0x38
ubsan_epilogue+0x10/0x54
__ubsan_handle_shift_out_of_bounds+0x180/0x194
__nvmem_cell_read+0x1ec/0x21c
nvmem_cell_read+0x58/0x94
nvmem_cell_read_variable_common+0x4c/0xb0
nvmem_cell_read_variable_le_u32+0x40/0x100
a6xx_gpu_init+0x170/0x2f4
adreno_bind+0x174/0x284
component_bind_all+0xf0/0x264
msm_drm_bind+0x1d8/0x7a0
try_to_bring_up_master+0x164/0x1ac
__component_add+0xbc/0x13c
component_add+0x20/0x2c
dp_display_probe+0x340/0x384
platform_probe+0xc0/0x100
really_probe+0x110/0x304
__driver_probe_device+0xb8/0x120
driver_probe_device+0x4c/0xfc
__device_attach_driver+0xb0/0x128
bus_for_each_drv+0x90/0xdc
__device_attach+0xc8/0x174
device_initial_probe+0x20/0x2c
bus_probe_device+0x40/0xa4
deferred_probe_work_func+0x7c/0xb8
process_one_work+0x128/0x21c
process_scheduled_works+0x40/0x54
worker_thread+0x1ec/0x2a8
kthread+0x138/0x158
ret_from_fork+0x10/0x20
Fix it by making sure there are any bits to mask out. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8712: fix use-after-free in rtl8712_dl_fw
Syzbot reported use-after-free in rtl8712_dl_fw(). The problem was in
race condition between r871xu_dev_remove() ->ndo_open() callback.
It's easy to see from crash log, that driver accesses released firmware
in ->ndo_open() callback. It may happen, since driver was releasing
firmware _before_ unregistering netdev. Fix it by moving
unregister_netdev() before cleaning up resources.
Call Trace:
...
rtl871x_open_fw drivers/staging/rtl8712/hal_init.c:83 [inline]
rtl8712_dl_fw+0xd95/0xe10 drivers/staging/rtl8712/hal_init.c:170
rtl8712_hal_init drivers/staging/rtl8712/hal_init.c:330 [inline]
rtl871x_hal_init+0xae/0x180 drivers/staging/rtl8712/hal_init.c:394
netdev_open+0xe6/0x6c0 drivers/staging/rtl8712/os_intfs.c:380
__dev_open+0x2bc/0x4d0 net/core/dev.c:1484
Freed by task 1306:
...
release_firmware+0x1b/0x30 drivers/base/firmware_loader/main.c:1053
r871xu_dev_remove+0xcc/0x2c0 drivers/staging/rtl8712/usb_intf.c:599
usb_unbind_interface+0x1d8/0x8d0 drivers/usb/core/driver.c:458 |
| In the Linux kernel, the following vulnerability has been resolved:
comedi: dt9812: fix DMA buffers on stack
USB transfer buffers are typically mapped for DMA and must not be
allocated on the stack or transfers will fail.
Allocate proper transfer buffers in the various command helpers and
return an error on short transfers instead of acting on random stack
data.
Note that this also fixes a stack info leak on systems where DMA is not
used as 32 bytes are always sent to the device regardless of how short
the command is. |
| In the Linux kernel, the following vulnerability has been resolved:
comedi: vmk80xx: fix transfer-buffer overflows
The driver uses endpoint-sized USB transfer buffers but up until
recently had no sanity checks on the sizes.
Commit e1f13c879a7c ("staging: comedi: check validity of wMaxPacketSize
of usb endpoints found") inadvertently fixed NULL-pointer dereferences
when accessing the transfer buffers in case a malicious device has a
zero wMaxPacketSize.
Make sure to allocate buffers large enough to handle also the other
accesses that are done without a size check (e.g. byte 18 in
vmk80xx_cnt_insn_read() for the VMK8061_MODEL) to avoid writing beyond
the buffers, for example, when doing descriptor fuzzing.
The original driver was for a low-speed device with 8-byte buffers.
Support was later added for a device that uses bulk transfers and is
presumably a full-speed device with a maximum 64-byte wMaxPacketSize. |
| In the Linux kernel, the following vulnerability has been resolved:
pmdomain: imx8mp-blk-ctrl: imx8mp_blk: Add fdcc clock to hdmimix domain
According to i.MX8MP RM and HDMI ADD, the fdcc clock is part of
hdmi rx verification IP that should not enable for HDMI TX.
But actually if the clock is disabled before HDMI/LCDIF probe,
LCDIF will not get pixel clock from HDMI PHY and print the error
logs:
[CRTC:39:crtc-2] vblank wait timed out
WARNING: CPU: 2 PID: 9 at drivers/gpu/drm/drm_atomic_helper.c:1634 drm_atomic_helper_wait_for_vblanks.part.0+0x23c/0x260
Add fdcc clock to LCDIF and HDMI TX power domains to fix the issue. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5: Register devlink first under devlink lock
In case device is having a non fatal FW error during probe, the
driver will report the error to user via devlink. This will trigger
a WARN_ON, since mlx5 is calling devlink_register() last.
In order to avoid the WARN_ON[1], change mlx5 to invoke devl_register()
first under devlink lock.
[1]
WARNING: CPU: 5 PID: 227 at net/devlink/health.c:483 devlink_recover_notify.constprop.0+0xb8/0xc0
CPU: 5 PID: 227 Comm: kworker/u16:3 Not tainted 6.4.0-rc5_for_upstream_min_debug_2023_06_12_12_38 #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Workqueue: mlx5_health0000:08:00.0 mlx5_fw_reporter_err_work [mlx5_core]
RIP: 0010:devlink_recover_notify.constprop.0+0xb8/0xc0
Call Trace:
<TASK>
? __warn+0x79/0x120
? devlink_recover_notify.constprop.0+0xb8/0xc0
? report_bug+0x17c/0x190
? handle_bug+0x3c/0x60
? exc_invalid_op+0x14/0x70
? asm_exc_invalid_op+0x16/0x20
? devlink_recover_notify.constprop.0+0xb8/0xc0
devlink_health_report+0x4a/0x1c0
mlx5_fw_reporter_err_work+0xa4/0xd0 [mlx5_core]
process_one_work+0x1bb/0x3c0
? process_one_work+0x3c0/0x3c0
worker_thread+0x4d/0x3c0
? process_one_work+0x3c0/0x3c0
kthread+0xc6/0xf0
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x1f/0x30
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
tls: get psock ref after taking rxlock to avoid leak
At the start of tls_sw_recvmsg, we take a reference on the psock, and
then call tls_rx_reader_lock. If that fails, we return directly
without releasing the reference.
Instead of adding a new label, just take the reference after locking
has succeeded, since we don't need it before. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix transaction atomicity bug when enabling simple quotas
Set squota incompat bit before committing the transaction that enables
the feature.
With the config CONFIG_BTRFS_ASSERT enabled, an assertion
failure occurs regarding the simple quota feature.
[5.596534] assertion failed: btrfs_fs_incompat(fs_info, SIMPLE_QUOTA), in fs/btrfs/qgroup.c:365
[5.597098] ------------[ cut here ]------------
[5.597371] kernel BUG at fs/btrfs/qgroup.c:365!
[5.597946] CPU: 1 UID: 0 PID: 268 Comm: mount Not tainted 6.13.0-rc2-00031-gf92f4749861b #146
[5.598450] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-debian-1.16.2-1 04/01/2014
[5.599008] RIP: 0010:btrfs_read_qgroup_config+0x74d/0x7a0
[5.604303] <TASK>
[5.605230] ? btrfs_read_qgroup_config+0x74d/0x7a0
[5.605538] ? exc_invalid_op+0x56/0x70
[5.605775] ? btrfs_read_qgroup_config+0x74d/0x7a0
[5.606066] ? asm_exc_invalid_op+0x1f/0x30
[5.606441] ? btrfs_read_qgroup_config+0x74d/0x7a0
[5.606741] ? btrfs_read_qgroup_config+0x74d/0x7a0
[5.607038] ? try_to_wake_up+0x317/0x760
[5.607286] open_ctree+0xd9c/0x1710
[5.607509] btrfs_get_tree+0x58a/0x7e0
[5.608002] vfs_get_tree+0x2e/0x100
[5.608224] fc_mount+0x16/0x60
[5.608420] btrfs_get_tree+0x2f8/0x7e0
[5.608897] vfs_get_tree+0x2e/0x100
[5.609121] path_mount+0x4c8/0xbc0
[5.609538] __x64_sys_mount+0x10d/0x150
The issue can be easily reproduced using the following reproducer:
root@q:linux# cat repro.sh
set -e
mkfs.btrfs -q -f /dev/sdb
mount /dev/sdb /mnt/btrfs
btrfs quota enable -s /mnt/btrfs
umount /mnt/btrfs
mount /dev/sdb /mnt/btrfs
The issue is that when enabling quotas, at btrfs_quota_enable(), we set
BTRFS_QGROUP_STATUS_FLAG_SIMPLE_MODE at fs_info->qgroup_flags and persist
it in the quota root in the item with the key BTRFS_QGROUP_STATUS_KEY, but
we only set the incompat bit BTRFS_FEATURE_INCOMPAT_SIMPLE_QUOTA after we
commit the transaction used to enable simple quotas.
This means that if after that transaction commit we unmount the filesystem
without starting and committing any other transaction, or we have a power
failure, the next time we mount the filesystem we will find the flag
BTRFS_QGROUP_STATUS_FLAG_SIMPLE_MODE set in the item with the key
BTRFS_QGROUP_STATUS_KEY but we will not find the incompat bit
BTRFS_FEATURE_INCOMPAT_SIMPLE_QUOTA set in the superblock, triggering an
assertion failure at:
btrfs_read_qgroup_config() -> qgroup_read_enable_gen()
To fix this issue, set the BTRFS_FEATURE_INCOMPAT_SIMPLE_QUOTA flag
immediately after setting the BTRFS_QGROUP_STATUS_FLAG_SIMPLE_MODE.
This ensures that both flags are flushed to disk within the same
transaction. |
| In the Linux kernel, the following vulnerability has been resolved:
comedi: vmk80xx: fix bulk-buffer overflow
The driver is using endpoint-sized buffers but must not assume that the
tx and rx buffers are of equal size or a malicious device could overflow
the slab-allocated receive buffer when doing bulk transfers. |
| In the Linux kernel, the following vulnerability has been resolved:
net: wwan: t7xx: Split 64bit accesses to fix alignment issues
Some of the registers are aligned on a 32bit boundary, causing
alignment faults on 64bit platforms.
Unable to handle kernel paging request at virtual address ffffffc084a1d004
Mem abort info:
ESR = 0x0000000096000061
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x21: alignment fault
Data abort info:
ISV = 0, ISS = 0x00000061, ISS2 = 0x00000000
CM = 0, WnR = 1, TnD = 0, TagAccess = 0
GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
swapper pgtable: 4k pages, 39-bit VAs, pgdp=0000000046ad6000
[ffffffc084a1d004] pgd=100000013ffff003, p4d=100000013ffff003, pud=100000013ffff003, pmd=0068000020a00711
Internal error: Oops: 0000000096000061 [#1] SMP
Modules linked in: mtk_t7xx(+) qcserial pppoe ppp_async option nft_fib_inet nf_flow_table_inet mt7921u(O) mt7921s(O) mt7921e(O) mt7921_common(O) iwlmvm(O) iwldvm(O) usb_wwan rndis_host qmi_wwan pppox ppp_generic nft_reject_ipv6 nft_reject_ipv4 nft_reject_inet nft_reject nft_redir nft_quota nft_numgen nft_nat nft_masq nft_log nft_limit nft_hash nft_flow_offload nft_fib_ipv6 nft_fib_ipv4 nft_fib nft_ct nft_chain_nat nf_tables nf_nat nf_flow_table nf_conntrack mt7996e(O) mt792x_usb(O) mt792x_lib(O) mt7915e(O) mt76_usb(O) mt76_sdio(O) mt76_connac_lib(O) mt76(O) mac80211(O) iwlwifi(O) huawei_cdc_ncm cfg80211(O) cdc_ncm cdc_ether wwan usbserial usbnet slhc sfp rtc_pcf8563 nfnetlink nf_reject_ipv6 nf_reject_ipv4 nf_log_syslog nf_defrag_ipv6 nf_defrag_ipv4 mt6577_auxadc mdio_i2c libcrc32c compat(O) cdc_wdm cdc_acm at24 crypto_safexcel pwm_fan i2c_gpio i2c_smbus industrialio i2c_algo_bit i2c_mux_reg i2c_mux_pca954x i2c_mux_pca9541 i2c_mux_gpio i2c_mux dummy oid_registry tun sha512_arm64 sha1_ce sha1_generic seqiv
md5 geniv des_generic libdes cbc authencesn authenc leds_gpio xhci_plat_hcd xhci_pci xhci_mtk_hcd xhci_hcd nvme nvme_core gpio_button_hotplug(O) dm_mirror dm_region_hash dm_log dm_crypt dm_mod dax usbcore usb_common ptp aquantia pps_core mii tpm encrypted_keys trusted
CPU: 3 PID: 5266 Comm: kworker/u9:1 Tainted: G O 6.6.22 #0
Hardware name: Bananapi BPI-R4 (DT)
Workqueue: md_hk_wq t7xx_fsm_uninit [mtk_t7xx]
pstate: 804000c5 (Nzcv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : t7xx_cldma_hw_set_start_addr+0x1c/0x3c [mtk_t7xx]
lr : t7xx_cldma_start+0xac/0x13c [mtk_t7xx]
sp : ffffffc085d63d30
x29: ffffffc085d63d30 x28: 0000000000000000 x27: 0000000000000000
x26: 0000000000000000 x25: ffffff80c804f2c0 x24: ffffff80ca196c05
x23: 0000000000000000 x22: ffffff80c814b9b8 x21: ffffff80c814b128
x20: 0000000000000001 x19: ffffff80c814b080 x18: 0000000000000014
x17: 0000000055c9806b x16: 000000007c5296d0 x15: 000000000f6bca68
x14: 00000000dbdbdce4 x13: 000000001aeaf72a x12: 0000000000000001
x11: 0000000000000000 x10: 0000000000000000 x9 : 0000000000000000
x8 : ffffff80ca1ef6b4 x7 : ffffff80c814b818 x6 : 0000000000000018
x5 : 0000000000000870 x4 : 0000000000000000 x3 : 0000000000000000
x2 : 000000010a947000 x1 : ffffffc084a1d004 x0 : ffffffc084a1d004
Call trace:
t7xx_cldma_hw_set_start_addr+0x1c/0x3c [mtk_t7xx]
t7xx_fsm_uninit+0x578/0x5ec [mtk_t7xx]
process_one_work+0x154/0x2a0
worker_thread+0x2ac/0x488
kthread+0xe0/0xec
ret_from_fork+0x10/0x20
Code: f9400800 91001000 8b214001 d50332bf (f9000022)
---[ end trace 0000000000000000 ]---
The inclusion of io-64-nonatomic-lo-hi.h indicates that all 64bit
accesses can be replaced by pairs of nonatomic 32bit access. Fix
alignment by forcing all accesses to be 32bit on 64bit platforms. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: PPC: Book3S HV: Fix stack handling in idle_kvm_start_guest()
In commit 10d91611f426 ("powerpc/64s: Reimplement book3s idle code in
C") kvm_start_guest() became idle_kvm_start_guest(). The old code
allocated a stack frame on the emergency stack, but didn't use the
frame to store anything, and also didn't store anything in its caller's
frame.
idle_kvm_start_guest() on the other hand is written more like a normal C
function, it creates a frame on entry, and also stores CR/LR into its
callers frame (per the ABI). The problem is that there is no caller
frame on the emergency stack.
The emergency stack for a given CPU is allocated with:
paca_ptrs[i]->emergency_sp = alloc_stack(limit, i) + THREAD_SIZE;
So emergency_sp actually points to the first address above the emergency
stack allocation for a given CPU, we must not store above it without
first decrementing it to create a frame. This is different to the
regular kernel stack, paca->kstack, which is initialised to point at an
initial frame that is ready to use.
idle_kvm_start_guest() stores the backchain, CR and LR all of which
write outside the allocation for the emergency stack. It then creates a
stack frame and saves the non-volatile registers. Unfortunately the
frame it creates is not large enough to fit the non-volatiles, and so
the saving of the non-volatile registers also writes outside the
emergency stack allocation.
The end result is that we corrupt whatever is at 0-24 bytes, and 112-248
bytes above the emergency stack allocation.
In practice this has gone unnoticed because the memory immediately above
the emergency stack happens to be used for other stack allocations,
either another CPUs mc_emergency_sp or an IRQ stack. See the order of
calls to irqstack_early_init() and emergency_stack_init().
The low addresses of another stack are the top of that stack, and so are
only used if that stack is under extreme pressue, which essentially
never happens in practice - and if it did there's a high likelyhood we'd
crash due to that stack overflowing.
Still, we shouldn't be corrupting someone else's stack, and it is purely
luck that we aren't corrupting something else.
To fix it we save CR/LR into the caller's frame using the existing r1 on
entry, we then create a SWITCH_FRAME_SIZE frame (which has space for
pt_regs) on the emergency stack with the backchain pointing to the
existing stack, and then finally we switch to the new frame on the
emergency stack. |
| In the Linux kernel, the following vulnerability has been resolved:
drm: Check output polling initialized before disabling
In drm_kms_helper_poll_disable() check if output polling
support is initialized before disabling polling. If not flag
this as a warning.
Additionally in drm_mode_config_helper_suspend() and
drm_mode_config_helper_resume() calls, that re the callers of these
functions, avoid invoking them if polling is not initialized.
For drivers like hyperv-drm, that do not initialize connector
polling, if suspend is called without this check, it leads to
suspend failure with following stack
[ 770.719392] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 770.720592] printk: Suspending console(s) (use no_console_suspend to debug)
[ 770.948823] ------------[ cut here ]------------
[ 770.948824] WARNING: CPU: 1 PID: 17197 at kernel/workqueue.c:3162 __flush_work.isra.0+0x212/0x230
[ 770.948831] Modules linked in: rfkill nft_counter xt_conntrack xt_owner udf nft_compat crc_itu_t nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_ct nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ip_set nf_tables nfnetlink vfat fat mlx5_ib ib_uverbs ib_core mlx5_core intel_rapl_msr intel_rapl_common kvm_amd ccp mlxfw kvm psample hyperv_drm tls drm_shmem_helper drm_kms_helper irqbypass pcspkr syscopyarea sysfillrect sysimgblt hv_balloon hv_utils joydev drm fuse xfs libcrc32c pci_hyperv pci_hyperv_intf sr_mod sd_mod cdrom t10_pi sg hv_storvsc scsi_transport_fc hv_netvsc serio_raw hyperv_keyboard hid_hyperv crct10dif_pclmul crc32_pclmul crc32c_intel hv_vmbus ghash_clmulni_intel dm_mirror dm_region_hash dm_log dm_mod
[ 770.948863] CPU: 1 PID: 17197 Comm: systemd-sleep Not tainted 5.14.0-362.2.1.el9_3.x86_64 #1
[ 770.948865] Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS Hyper-V UEFI Release v4.1 05/09/2022
[ 770.948866] RIP: 0010:__flush_work.isra.0+0x212/0x230
[ 770.948869] Code: 8b 4d 00 4c 8b 45 08 89 ca 48 c1 e9 04 83 e2 08 83 e1 0f 83 ca 02 89 c8 48 0f ba 6d 00 03 e9 25 ff ff ff 0f 0b e9 4e ff ff ff <0f> 0b 45 31 ed e9 44 ff ff ff e8 8f 89 b2 00 66 66 2e 0f 1f 84 00
[ 770.948870] RSP: 0018:ffffaf4ac213fb10 EFLAGS: 00010246
[ 770.948871] RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffffffff8c992857
[ 770.948872] RDX: 0000000000000001 RSI: 0000000000000001 RDI: ffff9aad82b00330
[ 770.948873] RBP: ffff9aad82b00330 R08: 0000000000000000 R09: ffff9aad87ee3d10
[ 770.948874] R10: 0000000000000200 R11: 0000000000000000 R12: ffff9aad82b00330
[ 770.948874] R13: 0000000000000001 R14: 0000000000000000 R15: 0000000000000001
[ 770.948875] FS: 00007ff1b2f6bb40(0000) GS:ffff9aaf37d00000(0000) knlGS:0000000000000000
[ 770.948878] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 770.948878] CR2: 0000555f345cb666 CR3: 00000001462dc005 CR4: 0000000000370ee0
[ 770.948879] Call Trace:
[ 770.948880] <TASK>
[ 770.948881] ? show_trace_log_lvl+0x1c4/0x2df
[ 770.948884] ? show_trace_log_lvl+0x1c4/0x2df
[ 770.948886] ? __cancel_work_timer+0x103/0x190
[ 770.948887] ? __flush_work.isra.0+0x212/0x230
[ 770.948889] ? __warn+0x81/0x110
[ 770.948891] ? __flush_work.isra.0+0x212/0x230
[ 770.948892] ? report_bug+0x10a/0x140
[ 770.948895] ? handle_bug+0x3c/0x70
[ 770.948898] ? exc_invalid_op+0x14/0x70
[ 770.948899] ? asm_exc_invalid_op+0x16/0x20
[ 770.948903] ? __flush_work.isra.0+0x212/0x230
[ 770.948905] __cancel_work_timer+0x103/0x190
[ 770.948907] ? _raw_spin_unlock_irqrestore+0xa/0x30
[ 770.948910] drm_kms_helper_poll_disable+0x1e/0x40 [drm_kms_helper]
[ 770.948923] drm_mode_config_helper_suspend+0x1c/0x80 [drm_kms_helper]
[ 770.948933] ? __pfx_vmbus_suspend+0x10/0x10 [hv_vmbus]
[ 770.948942] hyperv_vmbus_suspend+0x17/0x40 [hyperv_drm]
[ 770.948944] ? __pfx_vmbus_suspend+0x10/0x10 [hv_vmbus]
[ 770.948951] dpm_run_callback+0x4c/0x140
[ 770.948954] __device_suspend_noir
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
dpll: fix dpll_pin_on_pin_register() for multiple parent pins
In scenario where pin is registered with multiple parent pins via
dpll_pin_on_pin_register(..), all belonging to the same dpll device.
A second call to dpll_pin_on_pin_unregister(..) would cause a call trace,
as it tries to use already released registration resources (due to fix
introduced in b446631f355e). In this scenario pin was registered twice,
so resources are not yet expected to be release until each registered
pin/pin pair is unregistered.
Currently, the following crash/call trace is produced when ice driver is
removed on the system with installed E810T NIC which includes dpll device:
WARNING: CPU: 51 PID: 9155 at drivers/dpll/dpll_core.c:809 dpll_pin_ops+0x20/0x30
RIP: 0010:dpll_pin_ops+0x20/0x30
Call Trace:
? __warn+0x7f/0x130
? dpll_pin_ops+0x20/0x30
dpll_msg_add_pin_freq+0x37/0x1d0
dpll_cmd_pin_get_one+0x1c0/0x400
? __nlmsg_put+0x63/0x80
dpll_pin_event_send+0x93/0x140
dpll_pin_on_pin_unregister+0x3f/0x100
ice_dpll_deinit_pins+0xa1/0x230 [ice]
ice_remove+0xf1/0x210 [ice]
Fix by adding a parent pointer as a cookie when creating a registration,
also when searching for it. For the regular pins pass NULL, this allows to
create separated registration for each parent the pin is registered with. |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: ptdma: Fix the error handling path in pt_core_init()
In order to free resources correctly in the error handling path of
pt_core_init(), 2 goto's have to be switched. Otherwise, some resources
will leak and we will try to release things that have not been allocated
yet.
Also move a dev_err() to a place where it is more meaningful. |
| In the Linux kernel, the following vulnerability has been resolved:
mtd: parsers: qcom: Fix missing free for pparts in cleanup
Mtdpart doesn't free pparts when a cleanup function is declared.
Add missing free for pparts in cleanup function for smem to fix the
leak. |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: idxd: Convert spinlock to mutex to lock evl workqueue
drain_workqueue() cannot be called safely in a spinlocked context due to
possible task rescheduling. In the multi-task scenario, calling
queue_work() while drain_workqueue() will lead to a Call Trace as
pushing a work on a draining workqueue is not permitted in spinlocked
context.
Call Trace:
<TASK>
? __warn+0x7d/0x140
? __queue_work+0x2b2/0x440
? report_bug+0x1f8/0x200
? handle_bug+0x3c/0x70
? exc_invalid_op+0x18/0x70
? asm_exc_invalid_op+0x1a/0x20
? __queue_work+0x2b2/0x440
queue_work_on+0x28/0x30
idxd_misc_thread+0x303/0x5a0 [idxd]
? __schedule+0x369/0xb40
? __pfx_irq_thread_fn+0x10/0x10
? irq_thread+0xbc/0x1b0
irq_thread_fn+0x21/0x70
irq_thread+0x102/0x1b0
? preempt_count_add+0x74/0xa0
? __pfx_irq_thread_dtor+0x10/0x10
? __pfx_irq_thread+0x10/0x10
kthread+0x103/0x140
? __pfx_kthread+0x10/0x10
ret_from_fork+0x31/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
The current implementation uses a spinlock to protect event log workqueue
and will lead to the Call Trace due to potential task rescheduling.
To address the locking issue, convert the spinlock to mutex, allowing
the drain_workqueue() to be called in a safe mutex-locked context.
This change ensures proper synchronization when accessing the event log
workqueue, preventing potential Call Trace and improving the overall
robustness of the code. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: decrease MHI channel buffer length to 8KB
Currently buf_len field of ath11k_mhi_config_qca6390 is assigned
with 0, making MHI use a default size, 64KB, to allocate channel
buffers. This is likely to fail in some scenarios where system
memory is highly fragmented and memory compaction or reclaim is
not allowed.
There is a fail report which is caused by it:
kworker/u32:45: page allocation failure: order:4, mode:0x40c00(GFP_NOIO|__GFP_COMP), nodemask=(null),cpuset=/,mems_allowed=0
CPU: 0 PID: 19318 Comm: kworker/u32:45 Not tainted 6.8.0-rc3-1.gae4495f-default #1 openSUSE Tumbleweed (unreleased) 493b6d5b382c603654d7a81fc3c144d59a1dfceb
Workqueue: events_unbound async_run_entry_fn
Call Trace:
<TASK>
dump_stack_lvl+0x47/0x60
warn_alloc+0x13a/0x1b0
? srso_alias_return_thunk+0x5/0xfbef5
? __alloc_pages_direct_compact+0xab/0x210
__alloc_pages_slowpath.constprop.0+0xd3e/0xda0
__alloc_pages+0x32d/0x350
? mhi_prepare_channel+0x127/0x2d0 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
__kmalloc_large_node+0x72/0x110
__kmalloc+0x37c/0x480
? mhi_map_single_no_bb+0x77/0xf0 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
? mhi_prepare_channel+0x127/0x2d0 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
mhi_prepare_channel+0x127/0x2d0 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
__mhi_prepare_for_transfer+0x44/0x80 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
? __pfx_____mhi_prepare_for_transfer+0x10/0x10 [mhi 40df44e07c05479f7a6e7b90fba9f0e0031a7814]
device_for_each_child+0x5c/0xa0
? __pfx_pci_pm_resume+0x10/0x10
ath11k_core_resume+0x65/0x100 [ath11k a5094e22d7223135c40d93c8f5321cf09fd85e4e]
? srso_alias_return_thunk+0x5/0xfbef5
ath11k_pci_pm_resume+0x32/0x60 [ath11k_pci 830b7bfc3ea80ebef32e563cafe2cb55e9cc73ec]
? srso_alias_return_thunk+0x5/0xfbef5
dpm_run_callback+0x8c/0x1e0
device_resume+0x104/0x340
? __pfx_dpm_watchdog_handler+0x10/0x10
async_resume+0x1d/0x30
async_run_entry_fn+0x32/0x120
process_one_work+0x168/0x330
worker_thread+0x2f5/0x410
? __pfx_worker_thread+0x10/0x10
kthread+0xe8/0x120
? __pfx_kthread+0x10/0x10
ret_from_fork+0x34/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
Actually those buffers are used only by QMI target -> host communication.
And for WCN6855 and QCA6390, the largest packet size for that is less
than 6KB. So change buf_len field to 8KB, which results in order 1
allocation if page size is 4KB. In this way, we can at least save some
memory, and as well as decrease the possibility of allocation failure
in those scenarios.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30 |
| In the Linux kernel, the following vulnerability has been resolved:
iio: buffer: Fix file related error handling in IIO_BUFFER_GET_FD_IOCTL
If we fail to copy the just created file descriptor to userland, we
try to clean up by putting back 'fd' and freeing 'ib'. The code uses
put_unused_fd() for the former which is wrong, as the file descriptor
was already published by fd_install() which gets called internally by
anon_inode_getfd().
This makes the error handling code leaving a half cleaned up file
descriptor table around and a partially destructed 'file' object,
allowing userland to play use-after-free tricks on us, by abusing
the still usable fd and making the code operate on a dangling
'file->private_data' pointer.
Instead of leaving the kernel in a partially corrupted state, don't
attempt to explicitly clean up and leave this to the process exit
path that'll release any still valid fds, including the one created
by the previous call to anon_inode_getfd(). Simply return -EFAULT to
indicate the error. |
| In the Linux kernel, the following vulnerability has been resolved:
x86/fpu: Ensure shadow stack is active before "getting" registers
The x86 shadow stack support has its own set of registers. Those registers
are XSAVE-managed, but they are "supervisor state components" which means
that userspace can not touch them with XSAVE/XRSTOR. It also means that
they are not accessible from the existing ptrace ABI for XSAVE state.
Thus, there is a new ptrace get/set interface for it.
The regset code that ptrace uses provides an ->active() handler in
addition to the get/set ones. For shadow stack this ->active() handler
verifies that shadow stack is enabled via the ARCH_SHSTK_SHSTK bit in the
thread struct. The ->active() handler is checked from some call sites of
the regset get/set handlers, but not the ptrace ones. This was not
understood when shadow stack support was put in place.
As a result, both the set/get handlers can be called with
XFEATURE_CET_USER in its init state, which would cause get_xsave_addr() to
return NULL and trigger a WARN_ON(). The ssp_set() handler luckily has an
ssp_active() check to avoid surprising the kernel with shadow stack
behavior when the kernel is not ready for it (ARCH_SHSTK_SHSTK==0). That
check just happened to avoid the warning.
But the ->get() side wasn't so lucky. It can be called with shadow stacks
disabled, triggering the warning in practice, as reported by Christina
Schimpe:
WARNING: CPU: 5 PID: 1773 at arch/x86/kernel/fpu/regset.c:198 ssp_get+0x89/0xa0
[...]
Call Trace:
<TASK>
? show_regs+0x6e/0x80
? ssp_get+0x89/0xa0
? __warn+0x91/0x150
? ssp_get+0x89/0xa0
? report_bug+0x19d/0x1b0
? handle_bug+0x46/0x80
? exc_invalid_op+0x1d/0x80
? asm_exc_invalid_op+0x1f/0x30
? __pfx_ssp_get+0x10/0x10
? ssp_get+0x89/0xa0
? ssp_get+0x52/0xa0
__regset_get+0xad/0xf0
copy_regset_to_user+0x52/0xc0
ptrace_regset+0x119/0x140
ptrace_request+0x13c/0x850
? wait_task_inactive+0x142/0x1d0
? do_syscall_64+0x6d/0x90
arch_ptrace+0x102/0x300
[...]
Ensure that shadow stacks are active in a thread before looking them up
in the XSAVE buffer. Since ARCH_SHSTK_SHSTK and user_ssp[SHSTK_EN] are
set at the same time, the active check ensures that there will be
something to find in the XSAVE buffer.
[ dhansen: changelog/subject tweaks ] |
| In the Linux kernel, the following vulnerability has been resolved:
ocfs2: fix data corruption after conversion from inline format
Commit 6dbf7bb55598 ("fs: Don't invalidate page buffers in
block_write_full_page()") uncovered a latent bug in ocfs2 conversion
from inline inode format to a normal inode format.
The code in ocfs2_convert_inline_data_to_extents() attempts to zero out
the whole cluster allocated for file data by grabbing, zeroing, and
dirtying all pages covering this cluster. However these pages are
beyond i_size, thus writeback code generally ignores these dirty pages
and no blocks were ever actually zeroed on the disk.
This oversight was fixed by commit 693c241a5f6a ("ocfs2: No need to zero
pages past i_size.") for standard ocfs2 write path, inline conversion
path was apparently forgotten; the commit log also has a reasoning why
the zeroing actually is not needed.
After commit 6dbf7bb55598, things became worse as writeback code stopped
invalidating buffers on pages beyond i_size and thus these pages end up
with clean PageDirty bit but with buffers attached to these pages being
still dirty. So when a file is converted from inline format, then
writeback triggers, and then the file is grown so that these pages
become valid, the invalid dirtiness state is preserved,
mark_buffer_dirty() does nothing on these pages (buffers are already
dirty) but page is never written back because it is clean. So data
written to these pages is lost once pages are reclaimed.
Simple reproducer for the problem is:
xfs_io -f -c "pwrite 0 2000" -c "pwrite 2000 2000" -c "fsync" \
-c "pwrite 4000 2000" ocfs2_file
After unmounting and mounting the fs again, you can observe that end of
'ocfs2_file' has lost its contents.
Fix the problem by not doing the pointless zeroing during conversion
from inline format similarly as in the standard write path.
[[email protected]: fix whitespace, per Joseph] |
