| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: ctnetlink: fix refcount leak on table dump
There is a reference count leak in ctnetlink_dump_table():
if (res < 0) {
nf_conntrack_get(&ct->ct_general); // HERE
cb->args[1] = (unsigned long)ct;
...
While its very unlikely, its possible that ct == last.
If this happens, then the refcount of ct was already incremented.
This 2nd increment is never undone.
This prevents the conntrack object from being released, which in turn
keeps prevents cnet->count from dropping back to 0.
This will then block the netns dismantle (or conntrack rmmod) as
nf_conntrack_cleanup_net_list() will wait forever.
This can be reproduced by running conntrack_resize.sh selftest in a loop.
It takes ~20 minutes for me on a preemptible kernel on average before
I see a runaway kworker spinning in nf_conntrack_cleanup_net_list.
One fix would to change this to:
if (res < 0) {
if (ct != last)
nf_conntrack_get(&ct->ct_general);
But this reference counting isn't needed in the first place.
We can just store a cookie value instead.
A followup patch will do the same for ctnetlink_exp_dump_table,
it looks to me as if this has the same problem and like
ctnetlink_dump_table, we only need a 'skip hint', not the actual
object so we can apply the same cookie strategy there as well. |
| In the Linux kernel, the following vulnerability has been resolved:
rcu/nocb: Fix possible invalid rdp's->nocb_cb_kthread pointer access
In the preparation stage of CPU online, if the corresponding
the rdp's->nocb_cb_kthread does not exist, will be created,
there is a situation where the rdp's rcuop kthreads creation fails,
and then de-offload this CPU's rdp, does not assign this CPU's
rdp->nocb_cb_kthread pointer, but this rdp's->nocb_gp_rdp and
rdp's->rdp_gp->nocb_gp_kthread is still valid.
This will cause the subsequent re-offload operation of this offline
CPU, which will pass the conditional check and the kthread_unpark()
will access invalid rdp's->nocb_cb_kthread pointer.
This commit therefore use rdp's->nocb_gp_kthread instead of
rdp_gp's->nocb_gp_kthread for safety check. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/ptdump: take the memory hotplug lock inside ptdump_walk_pgd()
Memory hot remove unmaps and tears down various kernel page table regions
as required. The ptdump code can race with concurrent modifications of
the kernel page tables. When leaf entries are modified concurrently, the
dump code may log stale or inconsistent information for a VA range, but
this is otherwise not harmful.
But when intermediate levels of kernel page table are freed, the dump code
will continue to use memory that has been freed and potentially
reallocated for another purpose. In such cases, the ptdump code may
dereference bogus addresses, leading to a number of potential problems.
To avoid the above mentioned race condition, platforms such as arm64,
riscv and s390 take memory hotplug lock, while dumping kernel page table
via the sysfs interface /sys/kernel/debug/kernel_page_tables.
Similar race condition exists while checking for pages that might have
been marked W+X via /sys/kernel/debug/kernel_page_tables/check_wx_pages
which in turn calls ptdump_check_wx(). Instead of solving this race
condition again, let's just move the memory hotplug lock inside generic
ptdump_check_wx() which will benefit both the scenarios.
Drop get_online_mems() and put_online_mems() combination from all existing
platform ptdump code paths. |
| In the Linux kernel, the following vulnerability has been resolved:
eventpoll: Fix semi-unbounded recursion
Ensure that epoll instances can never form a graph deeper than
EP_MAX_NESTS+1 links.
Currently, ep_loop_check_proc() ensures that the graph is loop-free and
does some recursion depth checks, but those recursion depth checks don't
limit the depth of the resulting tree for two reasons:
- They don't look upwards in the tree.
- If there are multiple downwards paths of different lengths, only one of
the paths is actually considered for the depth check since commit
28d82dc1c4ed ("epoll: limit paths").
Essentially, the current recursion depth check in ep_loop_check_proc() just
serves to prevent it from recursing too deeply while checking for loops.
A more thorough check is done in reverse_path_check() after the new graph
edge has already been created; this checks, among other things, that no
paths going upwards from any non-epoll file with a length of more than 5
edges exist. However, this check does not apply to non-epoll files.
As a result, it is possible to recurse to a depth of at least roughly 500,
tested on v6.15. (I am unsure if deeper recursion is possible; and this may
have changed with commit 8c44dac8add7 ("eventpoll: Fix priority inversion
problem").)
To fix it:
1. In ep_loop_check_proc(), note the subtree depth of each visited node,
and use subtree depths for the total depth calculation even when a subtree
has already been visited.
2. Add ep_get_upwards_depth_proc() for similarly determining the maximum
depth of an upwards walk.
3. In ep_loop_check(), use these values to limit the total path length
between epoll nodes to EP_MAX_NESTS edges. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Reject narrower access to pointer ctx fields
The following BPF program, simplified from a syzkaller repro, causes a
kernel warning:
r0 = *(u8 *)(r1 + 169);
exit;
With pointer field sk being at offset 168 in __sk_buff. This access is
detected as a narrower read in bpf_skb_is_valid_access because it
doesn't match offsetof(struct __sk_buff, sk). It is therefore allowed
and later proceeds to bpf_convert_ctx_access. Note that for the
"is_narrower_load" case in the convert_ctx_accesses(), the insn->off
is aligned, so the cnt may not be 0 because it matches the
offsetof(struct __sk_buff, sk) in the bpf_convert_ctx_access. However,
the target_size stays 0 and the verifier errors with a kernel warning:
verifier bug: error during ctx access conversion(1)
This patch fixes that to return a proper "invalid bpf_context access
off=X size=Y" error on the load instruction.
The same issue affects multiple other fields in context structures that
allow narrow access. Some other non-affected fields (for sk_msg,
sk_lookup, and sockopt) were also changed to use bpf_ctx_range_ptr for
consistency.
Note this syzkaller crash was reported in the "Closes" link below, which
used to be about a different bug, fixed in
commit fce7bd8e385a ("bpf/verifier: Handle BPF_LOAD_ACQ instructions
in insn_def_regno()"). Because syzbot somehow confused the two bugs,
the new crash and repro didn't get reported to the mailing list. |
| In the Linux kernel, the following vulnerability has been resolved:
padata: Fix pd UAF once and for all
There is a race condition/UAF in padata_reorder that goes back
to the initial commit. A reference count is taken at the start
of the process in padata_do_parallel, and released at the end in
padata_serial_worker.
This reference count is (and only is) required for padata_replace
to function correctly. If padata_replace is never called then
there is no issue.
In the function padata_reorder which serves as the core of padata,
as soon as padata is added to queue->serial.list, and the associated
spin lock released, that padata may be processed and the reference
count on pd would go away.
Fix this by getting the next padata before the squeue->serial lock
is released.
In order to make this possible, simplify padata_reorder by only
calling it once the next padata arrives. |
| In the Linux kernel, the following vulnerability has been resolved:
perf/x86/intel: Fix crash in icl_update_topdown_event()
The perf_fuzzer found a hard-lockup crash on a RaptorLake machine:
Oops: general protection fault, maybe for address 0xffff89aeceab400: 0000
CPU: 23 UID: 0 PID: 0 Comm: swapper/23
Tainted: [W]=WARN
Hardware name: Dell Inc. Precision 9660/0VJ762
RIP: 0010:native_read_pmc+0x7/0x40
Code: cc e8 8d a9 01 00 48 89 03 5b cd cc cc cc cc 0f 1f ...
RSP: 000:fffb03100273de8 EFLAGS: 00010046
....
Call Trace:
<TASK>
icl_update_topdown_event+0x165/0x190
? ktime_get+0x38/0xd0
intel_pmu_read_event+0xf9/0x210
__perf_event_read+0xf9/0x210
CPUs 16-23 are E-core CPUs that don't support the perf metrics feature.
The icl_update_topdown_event() should not be invoked on these CPUs.
It's a regression of commit:
f9bdf1f95339 ("perf/x86/intel: Avoid disable PMU if !cpuc->enabled in sample read")
The bug introduced by that commit is that the is_topdown_event() function
is mistakenly used to replace the is_topdown_count() call to check if the
topdown functions for the perf metrics feature should be invoked.
Fix it. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_core: Fix use-after-free in vhci_flush()
syzbot reported use-after-free in vhci_flush() without repro. [0]
From the splat, a thread close()d a vhci file descriptor while
its device was being used by iotcl() on another thread.
Once the last fd refcnt is released, vhci_release() calls
hci_unregister_dev(), hci_free_dev(), and kfree() for struct
vhci_data, which is set to hci_dev->dev->driver_data.
The problem is that there is no synchronisation after unlinking
hdev from hci_dev_list in hci_unregister_dev(). There might be
another thread still accessing the hdev which was fetched before
the unlink operation.
We can use SRCU for such synchronisation.
Let's run hci_dev_reset() under SRCU and wait for its completion
in hci_unregister_dev().
Another option would be to restore hci_dev->destruct(), which was
removed in commit 587ae086f6e4 ("Bluetooth: Remove unused
hci-destruct cb"). However, this would not be a good solution, as
we should not run hci_unregister_dev() while there are in-flight
ioctl() requests, which could lead to another data-race KCSAN splat.
Note that other drivers seem to have the same problem, for exmaple,
virtbt_remove().
[0]:
BUG: KASAN: slab-use-after-free in skb_queue_empty_lockless include/linux/skbuff.h:1891 [inline]
BUG: KASAN: slab-use-after-free in skb_queue_purge_reason+0x99/0x360 net/core/skbuff.c:3937
Read of size 8 at addr ffff88807cb8d858 by task syz.1.219/6718
CPU: 1 UID: 0 PID: 6718 Comm: syz.1.219 Not tainted 6.16.0-rc1-syzkaller-00196-g08207f42d3ff #0 PREEMPT(full)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/07/2025
Call Trace:
<TASK>
dump_stack_lvl+0x189/0x250 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:408 [inline]
print_report+0xd2/0x2b0 mm/kasan/report.c:521
kasan_report+0x118/0x150 mm/kasan/report.c:634
skb_queue_empty_lockless include/linux/skbuff.h:1891 [inline]
skb_queue_purge_reason+0x99/0x360 net/core/skbuff.c:3937
skb_queue_purge include/linux/skbuff.h:3368 [inline]
vhci_flush+0x44/0x50 drivers/bluetooth/hci_vhci.c:69
hci_dev_do_reset net/bluetooth/hci_core.c:552 [inline]
hci_dev_reset+0x420/0x5c0 net/bluetooth/hci_core.c:592
sock_do_ioctl+0xd9/0x300 net/socket.c:1190
sock_ioctl+0x576/0x790 net/socket.c:1311
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:907 [inline]
__se_sys_ioctl+0xf9/0x170 fs/ioctl.c:893
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7fcf5b98e929
Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 a8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007fcf5c7b9038 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00007fcf5bbb6160 RCX: 00007fcf5b98e929
RDX: 0000000000000000 RSI: 00000000400448cb RDI: 0000000000000009
RBP: 00007fcf5ba10b39 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 0000000000000000 R14: 00007fcf5bbb6160 R15: 00007ffd6353d528
</TASK>
Allocated by task 6535:
kasan_save_stack mm/kasan/common.c:47 [inline]
kasan_save_track+0x3e/0x80 mm/kasan/common.c:68
poison_kmalloc_redzone mm/kasan/common.c:377 [inline]
__kasan_kmalloc+0x93/0xb0 mm/kasan/common.c:394
kasan_kmalloc include/linux/kasan.h:260 [inline]
__kmalloc_cache_noprof+0x230/0x3d0 mm/slub.c:4359
kmalloc_noprof include/linux/slab.h:905 [inline]
kzalloc_noprof include/linux/slab.h:1039 [inline]
vhci_open+0x57/0x360 drivers/bluetooth/hci_vhci.c:635
misc_open+0x2bc/0x330 drivers/char/misc.c:161
chrdev_open+0x4c9/0x5e0 fs/char_dev.c:414
do_dentry_open+0xdf0/0x1970 fs/open.c:964
vfs_open+0x3b/0x340 fs/open.c:1094
do_open fs/namei.c:3887 [inline]
path_openat+0x2ee5/0x3830 fs/name
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
NFSD: fix race between nfsd registration and exports_proc
As of now nfsd calls create_proc_exports_entry() at start of init_nfsd
and cleanup by remove_proc_entry() at last of exit_nfsd.
Which causes kernel OOPs if there is race between below 2 operations:
(i) exportfs -r
(ii) mount -t nfsd none /proc/fs/nfsd
for 5.4 kernel ARM64:
CPU 1:
el1_irq+0xbc/0x180
arch_counter_get_cntvct+0x14/0x18
running_clock+0xc/0x18
preempt_count_add+0x88/0x110
prep_new_page+0xb0/0x220
get_page_from_freelist+0x2d8/0x1778
__alloc_pages_nodemask+0x15c/0xef0
__vmalloc_node_range+0x28c/0x478
__vmalloc_node_flags_caller+0x8c/0xb0
kvmalloc_node+0x88/0xe0
nfsd_init_net+0x6c/0x108 [nfsd]
ops_init+0x44/0x170
register_pernet_operations+0x114/0x270
register_pernet_subsys+0x34/0x50
init_nfsd+0xa8/0x718 [nfsd]
do_one_initcall+0x54/0x2e0
CPU 2 :
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000010
PC is at : exports_net_open+0x50/0x68 [nfsd]
Call trace:
exports_net_open+0x50/0x68 [nfsd]
exports_proc_open+0x2c/0x38 [nfsd]
proc_reg_open+0xb8/0x198
do_dentry_open+0x1c4/0x418
vfs_open+0x38/0x48
path_openat+0x28c/0xf18
do_filp_open+0x70/0xe8
do_sys_open+0x154/0x248
Sometimes it crashes at exports_net_open() and sometimes cache_seq_next_rcu().
and same is happening on latest 6.14 kernel as well:
[ 0.000000] Linux version 6.14.0-rc5-next-20250304-dirty
...
[ 285.455918] Unable to handle kernel paging request at virtual address 00001f4800001f48
...
[ 285.464902] pc : cache_seq_next_rcu+0x78/0xa4
...
[ 285.469695] Call trace:
[ 285.470083] cache_seq_next_rcu+0x78/0xa4 (P)
[ 285.470488] seq_read+0xe0/0x11c
[ 285.470675] proc_reg_read+0x9c/0xf0
[ 285.470874] vfs_read+0xc4/0x2fc
[ 285.471057] ksys_read+0x6c/0xf4
[ 285.471231] __arm64_sys_read+0x1c/0x28
[ 285.471428] invoke_syscall+0x44/0x100
[ 285.471633] el0_svc_common.constprop.0+0x40/0xe0
[ 285.471870] do_el0_svc_compat+0x1c/0x34
[ 285.472073] el0_svc_compat+0x2c/0x80
[ 285.472265] el0t_32_sync_handler+0x90/0x140
[ 285.472473] el0t_32_sync+0x19c/0x1a0
[ 285.472887] Code: f9400885 93407c23 937d7c27 11000421 (f86378a3)
[ 285.473422] ---[ end trace 0000000000000000 ]---
It reproduced simply with below script:
while [ 1 ]
do
/exportfs -r
done &
while [ 1 ]
do
insmod /nfsd.ko
mount -t nfsd none /proc/fs/nfsd
umount /proc/fs/nfsd
rmmod nfsd
done &
So exporting interfaces to user space shall be done at last and
cleanup at first place.
With change there is no Kernel OOPs. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nft_set_pipapo: clamp maximum map bucket size to INT_MAX
Otherwise, it is possible to hit WARN_ON_ONCE in __kvmalloc_node_noprof()
when resizing hashtable because __GFP_NOWARN is unset.
Similar to:
b541ba7d1f5a ("netfilter: conntrack: clamp maximum hashtable size to INT_MAX") |
| In the Linux kernel, the following vulnerability has been resolved:
net: clear the dst when changing skb protocol
A not-so-careful NAT46 BPF program can crash the kernel
if it indiscriminately flips ingress packets from v4 to v6:
BUG: kernel NULL pointer dereference, address: 0000000000000000
ip6_rcv_core (net/ipv6/ip6_input.c:190:20)
ipv6_rcv (net/ipv6/ip6_input.c:306:8)
process_backlog (net/core/dev.c:6186:4)
napi_poll (net/core/dev.c:6906:9)
net_rx_action (net/core/dev.c:7028:13)
do_softirq (kernel/softirq.c:462:3)
netif_rx (net/core/dev.c:5326:3)
dev_loopback_xmit (net/core/dev.c:4015:2)
ip_mc_finish_output (net/ipv4/ip_output.c:363:8)
NF_HOOK (./include/linux/netfilter.h:314:9)
ip_mc_output (net/ipv4/ip_output.c:400:5)
dst_output (./include/net/dst.h:459:9)
ip_local_out (net/ipv4/ip_output.c:130:9)
ip_send_skb (net/ipv4/ip_output.c:1496:8)
udp_send_skb (net/ipv4/udp.c:1040:8)
udp_sendmsg (net/ipv4/udp.c:1328:10)
The output interface has a 4->6 program attached at ingress.
We try to loop the multicast skb back to the sending socket.
Ingress BPF runs as part of netif_rx(), pushes a valid v6 hdr
and changes skb->protocol to v6. We enter ip6_rcv_core which
tries to use skb_dst(). But the dst is still an IPv4 one left
after IPv4 mcast output.
Clear the dst in all BPF helpers which change the protocol.
Try to preserve metadata dsts, those may carry non-routing
metadata. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nft_set_pipapo: prevent overflow in lookup table allocation
When calculating the lookup table size, ensure the following
multiplication does not overflow:
- desc->field_len[] maximum value is U8_MAX multiplied by
NFT_PIPAPO_GROUPS_PER_BYTE(f) that can be 2, worst case.
- NFT_PIPAPO_BUCKETS(f->bb) is 2^8, worst case.
- sizeof(unsigned long), from sizeof(*f->lt), lt in
struct nft_pipapo_field.
Then, use check_mul_overflow() to multiply by bucket size and then use
check_add_overflow() to the alignment for avx2 (if needed). Finally, add
lt_size_check_overflow() helper and use it to consolidate this.
While at it, replace leftover allocation using the GFP_KERNEL to
GFP_KERNEL_ACCOUNT for consistency, in pipapo_resize(). |
| In the Linux kernel, the following vulnerability has been resolved:
net: stmmac: make sure that ptp_rate is not 0 before configuring EST
If the ptp_rate recorded earlier in the driver happens to be 0, this
bogus value will propagate up to EST configuration, where it will
trigger a division by 0.
Prevent this division by 0 by adding the corresponding check and error
code. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: Kill timer properly at removal
The USB-audio MIDI code initializes the timer, but in a rare case, the
driver might be freed without the disconnect call. This leaves the
timer in an active state while the assigned object is released via
snd_usbmidi_free(), which ends up with a kernel warning when the debug
configuration is enabled, as spotted by fuzzer.
For avoiding the problem, put timer_shutdown_sync() at
snd_usbmidi_free(), so that the timer can be killed properly.
While we're at it, replace the existing timer_delete_sync() at the
disconnect callback with timer_shutdown_sync(), too. |
| In the Linux kernel, the following vulnerability has been resolved:
block: fix resource leak in blk_register_queue() error path
When registering a queue fails after blk_mq_sysfs_register() is
successful but the function later encounters an error, we need
to clean up the blk_mq_sysfs resources.
Add the missing blk_mq_sysfs_unregister() call in the error path
to properly clean up these resources and prevent a memory leak. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: mtk-pmic-keys - fix possible null pointer dereference
In mtk_pmic_keys_probe, the regs parameter is only set if the button is
parsed in the device tree. However, on hardware where the button is left
floating, that node will most likely be removed not to enable that
input. In that case the code will try to dereference a null pointer.
Let's use the regs struct instead as it is defined for all supported
platforms. Note that it is ok setting the key reg even if that latter is
disabled as the interrupt won't be enabled anyway. |
| In the Linux kernel, the following vulnerability has been resolved:
x86/mm: Eliminate window where TLB flushes may be inadvertently skipped
tl;dr: There is a window in the mm switching code where the new CR3 is
set and the CPU should be getting TLB flushes for the new mm. But
should_flush_tlb() has a bug and suppresses the flush. Fix it by
widening the window where should_flush_tlb() sends an IPI.
Long Version:
=== History ===
There were a few things leading up to this.
First, updating mm_cpumask() was observed to be too expensive, so it was
made lazier. But being lazy caused too many unnecessary IPIs to CPUs
due to the now-lazy mm_cpumask(). So code was added to cull
mm_cpumask() periodically[2]. But that culling was a bit too aggressive
and skipped sending TLB flushes to CPUs that need them. So here we are
again.
=== Problem ===
The too-aggressive code in should_flush_tlb() strikes in this window:
// Turn on IPIs for this CPU/mm combination, but only
// if should_flush_tlb() agrees:
cpumask_set_cpu(cpu, mm_cpumask(next));
next_tlb_gen = atomic64_read(&next->context.tlb_gen);
choose_new_asid(next, next_tlb_gen, &new_asid, &need_flush);
load_new_mm_cr3(need_flush);
// ^ After 'need_flush' is set to false, IPIs *MUST*
// be sent to this CPU and not be ignored.
this_cpu_write(cpu_tlbstate.loaded_mm, next);
// ^ Not until this point does should_flush_tlb()
// become true!
should_flush_tlb() will suppress TLB flushes between load_new_mm_cr3()
and writing to 'loaded_mm', which is a window where they should not be
suppressed. Whoops.
=== Solution ===
Thankfully, the fuzzy "just about to write CR3" window is already marked
with loaded_mm==LOADED_MM_SWITCHING. Simply checking for that state in
should_flush_tlb() is sufficient to ensure that the CPU is targeted with
an IPI.
This will cause more TLB flush IPIs. But the window is relatively small
and I do not expect this to cause any kind of measurable performance
impact.
Update the comment where LOADED_MM_SWITCHING is written since it grew
yet another user.
Peter Z also raised a concern that should_flush_tlb() might not observe
'loaded_mm' and 'is_lazy' in the same order that switch_mm_irqs_off()
writes them. Add a barrier to ensure that they are observed in the
order they are written. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Scrub packet on bpf_redirect_peer
When bpf_redirect_peer is used to redirect packets to a device in
another network namespace, the skb isn't scrubbed. That can lead skb
information from one namespace to be "misused" in another namespace.
As one example, this is causing Cilium to drop traffic when using
bpf_redirect_peer to redirect packets that just went through IPsec
decryption to a container namespace. The following pwru trace shows (1)
the packet path from the host's XFRM layer to the container's XFRM
layer where it's dropped and (2) the number of active skb extensions at
each function.
NETNS MARK IFACE TUPLE FUNC
4026533547 d00 eth0 10.244.3.124:35473->10.244.2.158:53 xfrm_rcv_cb
.active_extensions = (__u8)2,
4026533547 d00 eth0 10.244.3.124:35473->10.244.2.158:53 xfrm4_rcv_cb
.active_extensions = (__u8)2,
4026533547 d00 eth0 10.244.3.124:35473->10.244.2.158:53 gro_cells_receive
.active_extensions = (__u8)2,
[...]
4026533547 0 eth0 10.244.3.124:35473->10.244.2.158:53 skb_do_redirect
.active_extensions = (__u8)2,
4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 ip_rcv
.active_extensions = (__u8)2,
4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 ip_rcv_core
.active_extensions = (__u8)2,
[...]
4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 udp_queue_rcv_one_skb
.active_extensions = (__u8)2,
4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 __xfrm_policy_check
.active_extensions = (__u8)2,
4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 __xfrm_decode_session
.active_extensions = (__u8)2,
4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 security_xfrm_decode_session
.active_extensions = (__u8)2,
4026534999 0 eth0 10.244.3.124:35473->10.244.2.158:53 kfree_skb_reason(SKB_DROP_REASON_XFRM_POLICY)
.active_extensions = (__u8)2,
In this case, there are no XFRM policies in the container's network
namespace so the drop is unexpected. When we decrypt the IPsec packet,
the XFRM state used for decryption is set in the skb extensions. This
information is preserved across the netns switch. When we reach the
XFRM policy check in the container's netns, __xfrm_policy_check drops
the packet with LINUX_MIB_XFRMINNOPOLS because a (container-side) XFRM
policy can't be found that matches the (host-side) XFRM state used for
decryption.
This patch fixes this by scrubbing the packet when using
bpf_redirect_peer, as is done on typical netns switches via veth
devices except skb->mark and skb->tstamp are not zeroed. |
| In the Linux kernel, the following vulnerability has been resolved:
net: phy: allow MDIO bus PM ops to start/stop state machine for phylink-controlled PHY
DSA has 2 kinds of drivers:
1. Those who call dsa_switch_suspend() and dsa_switch_resume() from
their device PM ops: qca8k-8xxx, bcm_sf2, microchip ksz
2. Those who don't: all others. The above methods should be optional.
For type 1, dsa_switch_suspend() calls dsa_user_suspend() -> phylink_stop(),
and dsa_switch_resume() calls dsa_user_resume() -> phylink_start().
These seem good candidates for setting mac_managed_pm = true because
that is essentially its definition [1], but that does not seem to be the
biggest problem for now, and is not what this change focuses on.
Talking strictly about the 2nd category of DSA drivers here (which
do not have MAC managed PM, meaning that for their attached PHYs,
mdio_bus_phy_suspend() and mdio_bus_phy_resume() should run in full),
I have noticed that the following warning from mdio_bus_phy_resume() is
triggered:
WARN_ON(phydev->state != PHY_HALTED && phydev->state != PHY_READY &&
phydev->state != PHY_UP);
because the PHY state machine is running.
It's running as a result of a previous dsa_user_open() -> ... ->
phylink_start() -> phy_start() having been initiated by the user.
The previous mdio_bus_phy_suspend() was supposed to have called
phy_stop_machine(), but it didn't. So this is why the PHY is in state
PHY_NOLINK by the time mdio_bus_phy_resume() runs.
mdio_bus_phy_suspend() did not call phy_stop_machine() because for
phylink, the phydev->adjust_link function pointer is NULL. This seems a
technicality introduced by commit fddd91016d16 ("phylib: fix PAL state
machine restart on resume"). That commit was written before phylink
existed, and was intended to avoid crashing with consumer drivers which
don't use the PHY state machine - phylink always does, when using a PHY.
But phylink itself has historically not been developed with
suspend/resume in mind, and apparently not tested too much in that
scenario, allowing this bug to exist unnoticed for so long. Plus, prior
to the WARN_ON(), it would have likely been invisible.
This issue is not in fact restricted to type 2 DSA drivers (according to
the above ad-hoc classification), but can be extrapolated to any MAC
driver with phylink and MDIO-bus-managed PHY PM ops. DSA is just where
the issue was reported. Assuming mac_managed_pm is set correctly, a
quick search indicates the following other drivers might be affected:
$ grep -Zlr PHYLINK_NETDEV drivers/ | xargs -0 grep -L mac_managed_pm
drivers/net/ethernet/atheros/ag71xx.c
drivers/net/ethernet/microchip/sparx5/sparx5_main.c
drivers/net/ethernet/microchip/lan966x/lan966x_main.c
drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.c
drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c
drivers/net/ethernet/freescale/ucc_geth.c
drivers/net/ethernet/freescale/enetc/enetc_pf_common.c
drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
drivers/net/ethernet/marvell/mvneta.c
drivers/net/ethernet/marvell/prestera/prestera_main.c
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/altera/altera_tse_main.c
drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
drivers/net/ethernet/meta/fbnic/fbnic_phylink.c
drivers/net/ethernet/tehuti/tn40_phy.c
drivers/net/ethernet/mscc/ocelot_net.c
Make the existing conditions dependent on the PHY device having a
phydev->phy_link_change() implementation equal to the default
phy_link_change() provided by phylib. Otherwise, we implicitly know that
the phydev has the phylink-provided phylink_phy_change() callback, and
when phylink is used, the PHY state machine always needs to be stopped/
started on the suspend/resume path. The code is structured as such that
if phydev->phy_link_change() is absent, it is a matter of time until the
kernel will crash - no need to further complicate the test.
Thus, for the situation where the PM is not managed b
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
net: ethernet: mtk-star-emac: fix spinlock recursion issues on rx/tx poll
Use spin_lock_irqsave and spin_unlock_irqrestore instead of spin_lock
and spin_unlock in mtk_star_emac driver to avoid spinlock recursion
occurrence that can happen when enabling the DMA interrupts again in
rx/tx poll.
```
BUG: spinlock recursion on CPU#0, swapper/0/0
lock: 0xffff00000db9cf20, .magic: dead4ead, .owner: swapper/0/0,
.owner_cpu: 0
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted
6.15.0-rc2-next-20250417-00001-gf6a27738686c-dirty #28 PREEMPT
Hardware name: MediaTek MT8365 Open Platform EVK (DT)
Call trace:
show_stack+0x18/0x24 (C)
dump_stack_lvl+0x60/0x80
dump_stack+0x18/0x24
spin_dump+0x78/0x88
do_raw_spin_lock+0x11c/0x120
_raw_spin_lock+0x20/0x2c
mtk_star_handle_irq+0xc0/0x22c [mtk_star_emac]
__handle_irq_event_percpu+0x48/0x140
handle_irq_event+0x4c/0xb0
handle_fasteoi_irq+0xa0/0x1bc
handle_irq_desc+0x34/0x58
generic_handle_domain_irq+0x1c/0x28
gic_handle_irq+0x4c/0x120
do_interrupt_handler+0x50/0x84
el1_interrupt+0x34/0x68
el1h_64_irq_handler+0x18/0x24
el1h_64_irq+0x6c/0x70
regmap_mmio_read32le+0xc/0x20 (P)
_regmap_bus_reg_read+0x6c/0xac
_regmap_read+0x60/0xdc
regmap_read+0x4c/0x80
mtk_star_rx_poll+0x2f4/0x39c [mtk_star_emac]
__napi_poll+0x38/0x188
net_rx_action+0x164/0x2c0
handle_softirqs+0x100/0x244
__do_softirq+0x14/0x20
____do_softirq+0x10/0x20
call_on_irq_stack+0x24/0x64
do_softirq_own_stack+0x1c/0x40
__irq_exit_rcu+0xd4/0x10c
irq_exit_rcu+0x10/0x1c
el1_interrupt+0x38/0x68
el1h_64_irq_handler+0x18/0x24
el1h_64_irq+0x6c/0x70
cpuidle_enter_state+0xac/0x320 (P)
cpuidle_enter+0x38/0x50
do_idle+0x1e4/0x260
cpu_startup_entry+0x34/0x3c
rest_init+0xdc/0xe0
console_on_rootfs+0x0/0x6c
__primary_switched+0x88/0x90
``` |
