| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm: don't tear down KMS twice when KMS init fails
When priv->kms_init() (mdp4_kms_init() / mdp5_kms_init()) fails partway
through, both display drivers already tear their KMS state down via
mdp4_destroy() / mdp5_kms_destroy() before returning the error. The
common error path in msm_drm_init() then runs msm_drm_uninit() ->
msm_drm_kms_uninit(), which tries to destroy the very same KMS a second
time, which causes a use-after-free crash.
Bring MDP4/MDP5 in line with the DPU driver whose dpu_kms_init() doesn't
perform error cleanup on the failure. Let the common path own the
cleanup, instead of freeing the KMS from their error paths.
The crash trace for the reference:
__lock_acquire from lock_acquire (kernel/locking/lockdep.c:5906 kernel/locking/lockdep.c:5863)
lock_acquire from touch_wq_lockdep_map (kernel/workqueue.c:4094 (discriminator 1))
touch_wq_lockdep_map from __flush_workqueue (kernel/workqueue.c:4136)
__flush_workqueue from msm_drm_kms_uninit (drivers/gpu/drm/msm/msm_kms.c:243 (discriminator 33))
msm_drm_kms_uninit from msm_drm_uninit (drivers/gpu/drm/msm/msm_drv.c:93)
msm_drm_uninit from msm_drm_init (drivers/gpu/drm/msm/msm_drv.c:184)
msm_drm_init from try_to_bring_up_aggregate_device (drivers/base/component.c:249 drivers/base/component.c:227)
try_to_bring_up_aggregate_device from __component_add (drivers/base/component.c:269 drivers/base/component.c:748)
__component_add from dsi_host_attach (drivers/gpu/drm/msm/dsi/dsi_host.c:1739)
dsi_host_attach from mipi_dsi_attach (drivers/gpu/drm/drm_mipi_dsi.c:383)
mipi_dsi_attach from sharp_nt_panel_probe (drivers/gpu/drm/panel/panel-sharp-ls043t1le01.c:247)
Patchwork: https://patchwork.freedesktop.org/patch/742068/ |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm/dsi: Drop dev_pm_opp_set_rate(0)
dev_pm_opp_set_rate(0) removes the vote specified in required-opps but
does not actually park the clock, making it run without the necessary
power backing. Drop the explicit call to it.
Every call site of ops->link_clk_disable() is followed by
pm_runtime_put(), so the power vote will be rescinded if deemed safe.
Patchwork: https://patchwork.freedesktop.org/patch/742783/ |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: fix leak in ath11k_service_ready_ext_event()
Currently, during ath11k_service_ready_ext_event() processing,
svc_rdy_ext.mac_phy_caps can be allocated during TLV parsing. This is a
temporary allocation that is freed on the success path, but not on the
error path. If parsing succeeds far enough to allocate mac_phy_caps and
then fails on a later TLV, the allocation leaks. So free the allocation
on the error path.
Compile tested only. |
| In the Linux kernel, the following vulnerability has been resolved:
regulator: core: use system_freezable_wq for init complete work
schedule_delayed_work() uses system_wq, which is non-freezable, allowing
regulator_init_complete_work to run concurrently with system suspend. This
work fires ~30s after boot to disable unused regulators via I2C. When it
races with PM suspend, the I2C adapter may already be suspended, triggering
a -ESHUTDOWN warning in __i2c_transfer():
WARNING: ... at __i2c_transfer+0x36c/0x3c8
Call trace:
__i2c_transfer
i2c_transfer
regmap_i2c_write
_regmap_update_bits
regulator_disable_regmap
_regulator_do_disable
regulator_late_cleanup
regulator_init_complete_work_function
process_one_work
Switch to system_freezable_wq so the work is frozen before any device
is suspended, eliminating the race. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Reject >8 byte return values on return-reading trampoline paths
btf_distill_func_proto() builds the function model used for the
fentry/fexit/fmod_ret/fsession trampolines and struct_ops. It has
accepted a 16-byte __int128 return value since the trampoline was
introduced: __get_type_size() returns the integer's type size, and the
return-type check only rejected ret < 0.
But the BPF trampoline preserves only 8 bytes of the return value (RAX on
x86, i.e. R0). For an attach type that reads the target's return value the
second half (RDX / R3) is neither saved nor restored, so a program
attached to a function returning a 16-byte value corrupts the value seen
by the real caller and itself observes only half of it. struct_ops
trampolines have the same limitation.
This affects the attach types that read the target's return value: fexit,
fmod_ret and fsession (plus the _multi variants of fexit and fsession),
and struct_ops. fentry/fentry_multi run before the target returns and are
unaffected.
Reject a >8 byte return value for these attach types in
bpf_check_attach_target() and bpf_check_attach_btf_id_multi(), and for
struct_ops in bpf_struct_ops_desc_init(). |
| In the Linux kernel, the following vulnerability has been resolved:
bpf, x86: Fix trampoline stack size for 128-bit arguments
btf_distill_func_proto() accepts a function argument up to 16 bytes, so a
128-bit scalar such as __int128 reaches the x86 trampoline with
arg_size == 16. But the current implementation assumes an __int128
argument only needs one register, so the register save area is
under-allocated and save_args() overwrites adjacent stack slots.
Compute the register count from arg_size for all arguments to fix it. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7915: unlink TWT flow if the MCU rejects the agreement
The flow is added to dev->twt_list before sending the agreement to the
firmware, but the error path leaves it linked while flowid_mask is
never set. The flow slot can then be reused and memset while still on
the list, corrupting twt_list, and station removal leaves a dangling
entry behind that mt7915_mac_twt_sched_list_add() later walks. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: free vif links after clearing wcid entries on full reset
mt7996_mac_reset_vif_iter() queues non-default vif links for kfree_rcu
while dev->wcid[] still holds pointers to the wcid embedded in each
freed link; mt76_reset_device() then dereferences those entries and
runs mt76_wcid_cleanup() on them. If a grace period elapses in between,
the cleanup operates on freed memory.
Run mt76_reset_device() first, so the wcid entries are cleaned up and
cleared while the links are still valid. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: clear stale link state on full reset
After a full chip reset, mac80211 reconfig replays interface, link and
channel context setup. mt7996_vif_link_add() short-circuits when the
link_id is still marked in mvif->valid_links, a state introduced for
postponing link teardown to interface removal. The reset path frees the
link structures without clearing those bits, so the replayed setup never
re-creates dev_info/bss_info/STA records in the restarted firmware and
never re-registers the link wcid, leaving the device inoperative.
The reset path also leaks every allocated MLD index: per-link indices
and the per-vif group/remap indices are re-allocated from scratch during
reconfig, but the old bits stay set in the masks, so repeated full
resets exhaust the index space.
Clear valid_links in the reset vif iterator and reset the MLD index
masks alongside the existing omac_mask clearing. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7915: fix double hif2 init on the non-WED path
mt7915_pci_init_hif2() was called unconditionally and again inside the
WED-inactive branch. The helper increments the global hif_idx, writes the
PCIe RECOG_ID register and takes a get_device() reference via
mt7915_pci_get_hif2(), while removal only drops one reference. On non-WED
dual-hif hardware this double-incremented hif_idx, wrote RECOG_ID twice and
leaked a device reference. Only the call inside the WED-inactive branch is
correct; drop the unconditional one. hif2 is already initialised to NULL. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7915: fix ext PHY use-after-free on register error path
After mt7915_register_ext_phy() succeeded, a failure of the main PHY
mt7915_init_debugfs() or mt7915_coredump_register() unwound through
free_phy2, which called ieee80211_free_hw() on the ext PHY hw while it
was still registered with mac80211, since mt76_unregister_device() only
unregisters the main hw. Unregister the ext PHY (thermal + phy + hw)
first and skip the redundant free. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7915: release hif2 reference on probe IRQ failure
The hif2 reference obtained by mt7915_pci_init_hif2() is only released on
error paths that key off dev->hif2, which is not assigned until after the
IRQ setup. If pci_alloc_irq_vectors() or the primary devm_request_irq()
fails, the reference leaks. Drop it explicitly on those paths via
mt7915_put_hif2(). |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: do not attach hif2 WED when the main WED attach failed
If the WED attach for the primary PCIe function fails, the probe path
still attached wed_hif2 for the secondary function, leaving the device
in an inconsistent half-WED configuration that crashes later. The hif2
call also re-enabled hwrro_mode, which the failed primary attach had
just turned off.
Skip the hif2 WED setup when the primary WED device is not active. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: reject out-of-range link ids in mt76_vif_link()
mt76_vif_link() indexes mvif->link[] without validating link_id, but
callers pass mvif->deflink_id / msta->deflink_id, which hold
IEEE80211_LINK_UNSPECIFIED (0xf) until the first link has been added.
Since IEEE80211_MLD_MAX_NUM_LINKS is 15, that reads one element past the
end of the array, aliasing mt76_vif_data.offchannel_link.
Reachable via mt7996_set_tsf()/mt7996_offset_tsf() and
mt7996_net_fill_forward_path(). Bounds check link_id and return NULL,
matching mt7996_sta_link() and mt7996_sta_link_protected(). |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: fix out-of-bounds link array access in mt7996_tx()
When mac80211 leaves the link unspecified, mt7996_tx() substitutes the
primary link id of the station or vif. That value is
IEEE80211_LINK_UNSPECIFIED (0xf) until the first link has been added,
and it is then used unchecked to index vif->link_conf[],
mvif->mt76.link[] and sta->link[], all of which hold
IEEE80211_MLD_MAX_NUM_LINKS (15) entries.
Clamp the primary link id to the default link before using it, and use
the clamped value for the link_sta fallback as well. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath10k: snoc: use memcpy_fromio() for MSA ramdump
On WCN3990/SNOC the MSA region is mapped with devm_memremap(MEMREMAP_WT).
On arm64 such a mapping is not Normal-cacheable, so unaligned accesses to
it are not permitted. ath10k_msa_dump_memory() copies the region with a
plain memcpy(), whose optimized __pi_memcpy_generic implementation issues
wide/unaligned loads. This triggers an alignment fault (FSC=0x21) Oops in
ath10k_snoc_fw_crashed_dump() while collecting the devcoredump:
Unable to handle kernel paging request ... FSC=0x21: alignment fault
pc : __pi_memcpy_generic
lr : ath10k_snoc_fw_crashed_dump [ath10k_snoc]
The Oops both leaves the firmware RAM dump buffer zeroed (no dump is
captured) and crashes the kernel, which in turn breaks modem SSR
recovery.
Use memcpy_fromio(), which only performs accesses that are valid for such
a device-memory mapping. The generic memcpy_fromio() implementation aligns
the source before issuing word-sized reads and stores the destination with
put_unaligned(), so it is also safe for the coherent DMA allocation used on
the non-reserved-memory path. ath11k and ath12k use the same pattern
when copying target memory into crash dumps, so call it unconditionally
here too.
The MEMREMAP_WT pointer is a plain void *, so an explicit __iomem cast is
needed; use __force to keep sparse happy.
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.3.7.c5-00107-QCAHLSWMTPL-1 |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: ptrace: Keep 'orig_x0' in-sync with x0 on syscall entry
Commit e057b9477232 ("arm64: syscall: Ensure saved x0 is kept in-sync
with tracer updates") attempted to resolve a long-standing issue with
syscall entry tracing, where a tracer is able to manipulate the first
syscall argument without being subjected to seccomp or audit checking.
Unfortunately, that fix was incomplete [1], as it failed to update
'orig_x0' between a tracer updating x0 during a seccomp ptrace exit
(SECCOMP_RET_TRACE) and the seccomp filter being re-evaluated.
Rather than add hooks to the core seccomp code, instead move the
synchronisation code into the ptrace GPR and syscall setting code so
that 'orig_x0' is kept up to date with x0 whenever we're stopped on the
syscall entry path. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: nl80211: clean up color-change beacon data on errors
nl80211_color_change() calls nl80211_parse_beacon() for the beacon_next
template, which can allocate params.beacon_next.mbssid_ies and .rnr_ies.
A parsing failure returned directly instead of using the out: cleanup,
leaking any allocations completed before the error.
Allocate the nested attribute table before parsing beacon_next. Its
allocation failure can then return before beacon data exists, while a
later parsing failure uses out: to release the parsed data. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: fix P2P action frame handling without device vif
Some P2P action frame paths assume the P2P device vif is always
available. That is not true when userspace sends non-P2P public action
frames through the primary interface, or when action-frame abort runs
after the P2P device vif has not been created.
Fall back to the primary vif when aborting an action frame without a P2P
device vif, and guard P2P device saved IE access before using it for
peer channel search. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: disconnect on CSA to channel 0
The refactor for the CSA parsing erroneously equates channel
zero and no information present, leading it to ignore a CSA
on an AP that advertises a switch to that (invalid) channel.
This leads to not disconnecting, which we should. For Intel
devices, this can lead to a firmware crash.
Fix this by using an int type for the channel number as well
as the opclass, and using a (negative) value that cannot be
encoded in the element to indicate it's not present. |
