| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
tap: free page on error paths in tap_get_user_xdp()
tap_get_user_xdp() rejects a frame shorter than ETH_HLEN with -EINVAL,
and returns -ENOMEM when build_skb() fails. Both paths jump to the err
label without freeing the page that vhost_net_build_xdp() allocated for
the frame. tap_sendmsg() discards the per-buffer return value and always
returns 0, so vhost_tx_batch() takes the success path and never frees
the page; each rejected frame in a batch leaks one page-frag chunk.
Free the page on both error paths, before the skb is built. This is the
tap counterpart of the same leak in tun_xdp_one(). |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath5k: do not access array OOB
Vincent reports:
> The ath5k driver seems to do an array-index-out-of-bounds access as
> shown by the UBSAN kernel message:
> UBSAN: array-index-out-of-bounds in drivers/net/wireless/ath/ath5k/base.c:1741:20
> index 4 is out of range for type 'ieee80211_tx_rate [4]'
> ...
> Call Trace:
> <TASK>
> dump_stack_lvl+0x5d/0x80
> ubsan_epilogue+0x5/0x2b
> __ubsan_handle_out_of_bounds.cold+0x46/0x4b
> ath5k_tasklet_tx+0x4e0/0x560 [ath5k]
> tasklet_action_common+0xb5/0x1c0
It is real. 'ts->ts_final_idx' can be 3 on 5212, so:
info->status.rates[ts->ts_final_idx + 1].idx = -1;
with the array defined as:
struct ieee80211_tx_rate rates[IEEE80211_TX_MAX_RATES];
while the size is:
#define IEEE80211_TX_MAX_RATES 4
is indeed bogus.
Set this 'idx = -1' sentinel only if the array index is less than the
array size. As mac80211 will not look at rates beyond the size
(IEEE80211_TX_MAX_RATES).
Note: The effect of the OOB write is negligible. It just overwrites the
next member of info->status, i.e. ack_signal. |
| In the Linux kernel, the following vulnerability has been resolved:
flow_dissector: do not dissect PPPoE PFC frames
RFC 2516 Section 7 states that Protocol Field Compression (PFC) is NOT
RECOMMENDED for PPPoE. In practice, pppd does not support negotiating
PFC for PPPoE sessions, and the flow dissector driver has assumed an
uncompressed frame until the blamed commit.
During the review process of that commit [1], support for PFC is
suggested. However, having a compressed (1-byte) protocol field means
the subsequent PPP payload is shifted by one byte, causing 4-byte
misalignment for the network header and an unaligned access exception
on some architectures.
The exception can be reproduced by sending a PPPoE PFC frame to an
ethernet interface of a MIPS board, with RPS enabled, even if no PPPoE
session is active on that interface:
$ 0 : 00000000 80c40000 00000000 85144817
$ 4 : 00000008 00000100 80a75758 81dc9bb8
$ 8 : 00000010 8087ae2c 0000003d 00000000
$12 : 000000e0 00000039 00000000 00000000
$16 : 85043240 80a75758 81dc9bb8 00006488
$20 : 0000002f 00000007 85144810 80a70000
$24 : 81d1bda0 00000000
$28 : 81dc8000 81dc9aa8 00000000 805ead08
Hi : 00009d51
Lo : 2163358a
epc : 805e91f0 __skb_flow_dissect+0x1b0/0x1b50
ra : 805ead08 __skb_get_hash_net+0x74/0x12c
Status: 11000403 KERNEL EXL IE
Cause : 40800010 (ExcCode 04)
BadVA : 85144817
PrId : 0001992f (MIPS 1004Kc)
Call Trace:
[<805e91f0>] __skb_flow_dissect+0x1b0/0x1b50
[<805ead08>] __skb_get_hash_net+0x74/0x12c
[<805ef330>] get_rps_cpu+0x1b8/0x3fc
[<805fca70>] netif_receive_skb_list_internal+0x324/0x364
[<805fd120>] napi_complete_done+0x68/0x2a4
[<8058de5c>] mtk_napi_rx+0x228/0xfec
[<805fd398>] __napi_poll+0x3c/0x1c4
[<805fd754>] napi_threaded_poll_loop+0x234/0x29c
[<805fd848>] napi_threaded_poll+0x8c/0xb0
[<80053544>] kthread+0x104/0x12c
[<80002bd8>] ret_from_kernel_thread+0x14/0x1c
Code: 02d51821 1060045b 00000000 <8c640000> 3084000f 2c820005 144001a2 00042080 8e220000
To reduce the attack surface and maintain performance, do not process
PPPoE PFC frames.
[1] https://lore.kernel.org/r/[email protected] |
| In the Linux kernel, the following vulnerability has been resolved:
nvmet: avoid recursive nvmet-wq flush in nvmet_ctrl_free
nvmet_tcp_release_queue_work() runs on nvmet-wq and can drop the
final controller reference through nvmet_cq_put(). If that triggers
nvmet_ctrl_free(), the teardown path flushes ctrl->async_event_work on
the same nvmet-wq.
Call chain:
nvmet_tcp_schedule_release_queue()
kref_put(&queue->kref, nvmet_tcp_release_queue)
nvmet_tcp_release_queue()
queue_work(nvmet_wq, &queue->release_work) <--- nvmet_wq
process_one_work()
nvmet_tcp_release_queue_work()
nvmet_cq_put(&queue->nvme_cq)
nvmet_cq_destroy()
nvmet_ctrl_put(cq->ctrl)
nvmet_ctrl_free()
flush_work(&ctrl->async_event_work) <--- nvmet_wq
Previously Scheduled by :-
nvmet_add_async_event
queue_work(nvmet_wq, &ctrl->async_event_work);
This trips lockdep with a possible recursive locking warning.
[ 5223.015876] run blktests nvme/003 at 2026-04-07 20:53:55
[ 5223.061801] loop0: detected capacity change from 0 to 2097152
[ 5223.072206] nvmet: adding nsid 1 to subsystem blktests-subsystem-1
[ 5223.088368] nvmet_tcp: enabling port 0 (127.0.0.1:4420)
[ 5223.126086] nvmet: Created discovery controller 1 for subsystem nqn.2014-08.org.nvmexpress.discovery for NQN nqn.2014-08.org.nvmexpress:uuid:0f01fb42-9f7f-4856-b0b3-51e60b8de349.
[ 5223.128453] nvme nvme1: new ctrl: NQN "nqn.2014-08.org.nvmexpress.discovery", addr 127.0.0.1:4420, hostnqn: nqn.2014-08.org.nvmexpress:uuid:0f01fb42-9f7f-4856-b0b3-51e60b8de349
[ 5233.199447] nvme nvme1: Removing ctrl: NQN "nqn.2014-08.org.nvmexpress.discovery"
[ 5233.227718] ============================================
[ 5233.231283] WARNING: possible recursive locking detected
[ 5233.234696] 7.0.0-rc3nvme+ #20 Tainted: G O N
[ 5233.238434] --------------------------------------------
[ 5233.241852] kworker/u192:6/2413 is trying to acquire lock:
[ 5233.245429] ffff888111632548 ((wq_completion)nvmet-wq){+.+.}-{0:0}, at: touch_wq_lockdep_map+0x26/0x90
[ 5233.251438]
but task is already holding lock:
[ 5233.255254] ffff888111632548 ((wq_completion)nvmet-wq){+.+.}-{0:0}, at: process_one_work+0x5cc/0x6e0
[ 5233.261125]
other info that might help us debug this:
[ 5233.265333] Possible unsafe locking scenario:
[ 5233.269217] CPU0
[ 5233.270795] ----
[ 5233.272436] lock((wq_completion)nvmet-wq);
[ 5233.275241] lock((wq_completion)nvmet-wq);
[ 5233.278020]
*** DEADLOCK ***
[ 5233.281793] May be due to missing lock nesting notation
[ 5233.286195] 3 locks held by kworker/u192:6/2413:
[ 5233.289192] #0: ffff888111632548 ((wq_completion)nvmet-wq){+.+.}-{0:0}, at: process_one_work+0x5cc/0x6e0
[ 5233.294569] #1: ffffc9000e2a7e40 ((work_completion)(&queue->release_work)){+.+.}-{0:0}, at: process_one_work+0x1c5/0x6e0
[ 5233.300128] #2: ffffffff82d7dc40 (rcu_read_lock){....}-{1:3}, at: __flush_work+0x62/0x530
[ 5233.304290]
stack backtrace:
[ 5233.306520] CPU: 4 UID: 0 PID: 2413 Comm: kworker/u192:6 Tainted: G O N 7.0.0-rc3nvme+ #20 PREEMPT(full)
[ 5233.306524] Tainted: [O]=OOT_MODULE, [N]=TEST
[ 5233.306525] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.17.0-0-gb52ca86e094d-prebuilt.qemu.org 04/01/2014
[ 5233.306527] Workqueue: nvmet-wq nvmet_tcp_release_queue_work [nvmet_tcp]
[ 5233.306532] Call Trace:
[ 5233.306534] <TASK>
[ 5233.306536] dump_stack_lvl+0x73/0xb0
[ 5233.306552] print_deadlock_bug+0x225/0x2f0
[ 5233.306556] __lock_acquire+0x13f0/0x2290
[ 5233.306563] lock_acquire+0xd0/0x300
[ 5233.306565] ? touch_wq_lockdep_map+0x26/0x90
[ 5233.306571] ? __flush_work+0x20b/0x530
[ 5233.306573] ? touch_wq_lockdep_map+0x26/0x90
[ 5233.306577] touch_wq_lockdep_map+0x3b/0x90
[ 5233.306580] ? touch_wq_lockdep_map+0x26/0x90
[ 52
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
isofs: validate Rock Ridge CE continuation extent against volume size
rock_continue() reads rs->cont_extent verbatim from the Rock Ridge CE
record and passes it to sb_bread() without checking that the block
number is within the mounted ISO 9660 volume. commit e595447e177b
("[PATCH] rock.c: handle corrupted directories") added cont_offset
and cont_size rejection for the CE continuation but did not validate
the extent block number itself. commit f54e18f1b831 ("isofs: Fix
infinite looping over CE entries") later capped the CE chain length
at RR_MAX_CE_ENTRIES = 32 but again left the block number unchecked.
With a crafted ISO mounted via udisks2 (desktop optical auto-mount)
or via CAP_SYS_ADMIN mount, rs->cont_extent can therefore point at
an out-of-range block or at blocks belonging to an adjacent
filesystem on the same block device. sb_bread() on an out-of-range
block returns NULL cleanly via the block layer EIO path, so there
is no memory-safety violation. For in-range reads of adjacent-
filesystem data, the CE buffer is parsed as Rock Ridge records and
only the text of SL sub-records reaches userspace through
readlink(), which makes the info-leak channel narrow and difficult
to exploit; still, rejecting the malformed CE outright matches the
rejection shape already present in the same function for
cont_offset and cont_size.
Add an ISOFS_SB(sb)->s_nzones bounds check to rock_continue() next
to the existing offset/size rejection, printing the same
corrupted-directory-entry notice. |
| In the Linux kernel, the following vulnerability has been resolved:
dm: fix a buffer overflow in ioctl processing
Tony Asleson (using Claude) found a buffer overflow in dm-ioctl in the
function retrieve_status:
1. The code in retrieve_status checks that the output string fits into
the output buffer and writes the output string there
2. Then, the code aligns the "outptr" variable to the next 8-byte
boundary:
outptr = align_ptr(outptr);
3. The alignment doesn't check overflow, so outptr could point past the
buffer end
4. The "for" loop is iterated again, it executes:
remaining = len - (outptr - outbuf);
5. If "outptr" points past "outbuf + len", the arithmetics wraps around
and the variable "remaining" contains unusually high number
6. With "remaining" being high, the code writes more data past the end of
the buffer
Luckily, this bug has no security implications because:
1. Only root can issue device mapper ioctls
2. The commonly used libraries that communicate with device mapper
(libdevmapper and devicemapper-rs) use buffer size that is aligned to
8 bytes - thus, "outptr = align_ptr(outptr)" can't overshoot the input
buffer and the bug can't happen accidentally |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_uart: fix UAFs and race conditions in close and init paths
Vulnerabilities leading to Use-After-Free (UAF) and Null Pointer
Dereference (NPD) conditions were observed in the lifecycle management
of hci_uart.
The primary issue arises because the workqueues (init_ready and
write_work) are only flushed/cancelled if the HCI_UART_PROTO_READY
flag is set during TTY close. If a hangup occurs before setup completes,
hci_uart_tty_close() skips the teardown of these workqueues and
proceeds to free the `hu` struct. When the scheduled work executes
later, it blindly dereferences the freed `hu` struct.
Furthermore, several data races and UAFs were identified in the teardown
sequence:
1. Calling hci_uart_flush() from hci_uart_close() without effectively
disabling write_work causes a race condition where both can concurrently
double-free hu->tx_skb. This happens because protocol timers can
concurrently invoke hci_uart_tx_wakeup() and requeue write_work.
2. Calling hci_free_dev(hdev) before hu->proto->close(hu) causes a UAF
when vendor specific protocol close callbacks dereference hu->hdev.
3. In the initialization error paths, failing to take the proto_lock
write lock before clearing PROTO_READY leads to races with active
readers. Additionally, hci_uart_tty_receive() accesses hu->hdev
outside the read lock, leading to UAFs if the initialization error
path frees hdev concurrently.
Fix these synchronization and lifecycle issues by:
1. Re-ordering hci_uart_tty_close() to clear HCI_UART_PROTO_READY first,
followed immediately by a cancel_work_sync(&hu->write_work). Clearing
the flag locks out concurrent protocol timers from successfully invoking
hci_uart_tx_wakeup(), effectively rendering the cancellation permanent
and preventing the tx_skb double-free.
2. Note: Clearing PROTO_READY early causes hci_uart_close() to skip
hu->proto->flush(). This is perfectly safe in the tty_close path
because hu->proto->close() executes shortly after, which intrinsically
purges all protocol SKB queues and tears down the state.
3. Relocating hu->proto->close(hu) strictly prior to hci_free_dev(hdev)
across all close and error paths to prevent vendor-level UAFs.
4. Moving the hdev->stat.byte_rx increment in hci_uart_tty_receive()
inside the proto_lock read-side critical section to safely synchronize
with device unregistration.
5. Adding cancel_work_sync(&hu->write_work) to hci_uart_close() to safely
flush the workqueue before hci_uart_flush() is invoked via the HCI core.
6. Utilizing cancel_work_sync() instead of disable_work_sync() across
all paths to prevent permanently breaking user-space retry capabilities. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: reject userspace cifs.spnego descriptions
cifs.spnego key descriptions contain authority-bearing fields such as
pid, uid, creduid, and upcall_target that cifs.upcall treats as
kernel-originating inputs. However, userspace can also create keys of
this type through request_key(2) or add_key(2), allowing those fields to
be supplied without CIFS origin.
Only accept cifs.spnego descriptions while CIFS is using its private
spnego_cred to request the key. |
| In the Linux kernel, the following vulnerability has been resolved:
vsock: fix buffer size clamping order
In vsock_update_buffer_size(), the buffer size was being clamped to the
maximum first, and then to the minimum. If a user sets a minimum buffer
size larger than the maximum, the minimum check overrides the maximum
check, inverting the constraint.
This breaks the intended socket memory boundaries by allowing the
vsk->buffer_size to grow beyond the configured vsk->buffer_max_size.
Fix this by checking the minimum first, and then the maximum. This
ensures the buffer size never exceeds the buffer_max_size. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: revalidate list cursor after sctp_sendmsg_to_asoc() in SCTP_SENDALL
The SCTP_SENDALL path in sctp_sendmsg() iterates ep->asocs with
list_for_each_entry_safe(), which caches the next entry in @tmp before
the loop body runs. The body calls sctp_sendmsg_to_asoc(), which may
drop the socket lock inside sctp_wait_for_sndbuf().
While the lock is dropped, another thread can SCTP_SOCKOPT_PEELOFF the
association cached in @tmp, migrating it to a new endpoint via
sctp_sock_migrate() (list_del_init() + list_add_tail() to
newep->asocs), and optionally close the new socket which frees the
association via kfree_rcu(). The cached @tmp can also be freed by a
network ABORT for that association, processed in softirq while the
lock is dropped.
sctp_wait_for_sndbuf() revalidates @asoc (the current entry) on re-lock
via the "sk != asoc->base.sk" and "asoc->base.dead" checks, but nothing
revalidates @tmp. After a successful return, the iterator advances to
the stale @tmp, yielding either a use-after-free (if the peeled socket
was closed) or a list-walk onto the new endpoint's list head (type
confusion of &newep->asocs as a struct sctp_association *).
Both are reachable from CapEff=0; the type-confusion path gives
controlled indirect call via the outqueue.sched->init_sid pointer.
Fix by re-deriving @tmp from @asoc after sctp_sendmsg_to_asoc()
returns. @asoc is known to still be on ep->asocs at that point: the
only callers that list_del an association from ep->asocs are
sctp_association_free() (which sets asoc->base.dead) and
sctp_assoc_migrate() (which changes asoc->base.sk), and
sctp_wait_for_sndbuf() checks both under the lock before any
successful return; a tripped check propagates as err < 0 and the loop
bails before the re-derive.
The SCTP_ABORT path in sctp_sendmsg_check_sflags() returns 0 and the
loop hits 'continue' before sctp_sendmsg_to_asoc() is ever called, so
the @tmp cached by list_for_each_entry_safe() still covers the
lock-held free that ba59fb027307 ("sctp: walk the list of asoc
safely") was added for. |
| In the Linux kernel, the following vulnerability has been resolved:
vsock/virtio: fix accept queue count leak on transport mismatch
virtio_transport_recv_listen() calls sk_acceptq_added() before
vsock_assign_transport(). If vsock_assign_transport() fails or
selects a different transport, the error path returns without
calling sk_acceptq_removed(), permanently incrementing
sk_ack_backlog.
After approximately backlog+1 such failures, sk_acceptq_is_full()
returns true, causing the listener to reject all new connections.
Fix by moving sk_acceptq_added() to after the transport validation,
matching the pattern used by vmci_transport and hyperv_transport. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/gem: Fix inconsistent plane dimension calculation in drm_gem_fb_init_with_funcs()
drm_gem_fb_init_with_funcs() computes sub-sampled plane dimensions
using plain integer division:
unsigned int width = mode_cmd->width / (i ? info->hsub : 1);
unsigned int height = mode_cmd->height / (i ? info->vsub : 1);
However, the ioctl-level framebuffer_check() in drm_framebuffer.c uses
drm_format_info_plane_width/height() which round up dimensions via
DIV_ROUND_UP(). This inconsistency corrupts the subsequent GEM object
size check for certain pixel format and dimension combinations.
For example, with NV12 (vsub=2) and a 1-pixel-tall framebuffer the
GEM size validation path sees height=0 instead of height=1. The
expression (height - 1) then wraps to UINT_MAX as an unsigned int,
causing min_size to overflow and wrap back to a small value. A tiny
GEM object therefore passes the size guard, yet when the GPU accesses
the chroma plane it will read or write memory beyond the object's
bounds.
Fix by replacing the open-coded divisions with drm_format_info_plane_width()
and drm_format_info_plane_height(), which use DIV_ROUND_UP() and match
the calculation already used in framebuffer_check(). |
| In the Linux kernel, the following vulnerability has been resolved:
tracepoint: balance regfunc() on func_add() failure in tracepoint_add_func()
When a tracepoint goes through the 0 -> 1 transition, tracepoint_add_func()
invokes the subsystem's ext->regfunc() before attempting to install the
new probe via func_add(). If func_add() then fails (for example, when
allocate_probes() cannot allocate a new probe array under memory pressure
and returns -ENOMEM), the function returns the error without calling the
matching ext->unregfunc(), leaving the side effects of regfunc() behind
with no installed probe to justify them.
For syscall tracepoints this is particularly unpleasant: syscall_regfunc()
bumps sys_tracepoint_refcount and sets SYSCALL_TRACEPOINT on every task.
After a leaked failure, the refcount is stuck at a non-zero value with no
consumer, and every task continues paying the syscall trace entry/exit
overhead until reboot. Other subsystems providing regfunc()/unregfunc()
pairs exhibit similarly scoped persistent state.
Mirror the existing 1 -> 0 cleanup and call ext->unregfunc() in the
func_add() error path, gated on the same condition used there so the
unwind is symmetric with the registration. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: validate dacloffset before building DACL pointers
parse_sec_desc(), build_sec_desc(), and the chown path in
id_mode_to_cifs_acl() all add the server-supplied dacloffset to pntsd
before proving a DACL header fits inside the returned security
descriptor.
On 32-bit builds a malicious server can return dacloffset near
U32_MAX, wrap the derived DACL pointer below end_of_acl, and then slip
past the later pointer-based bounds checks. build_sec_desc() and
id_mode_to_cifs_acl() can then dereference DACL fields from the wrapped
pointer in the chmod/chown rewrite paths.
Validate dacloffset numerically before building any DACL pointer and
reuse the same helper at the three DACL entry points. |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: ah: account for ESN high bits in async callbacks
AH allocates its temporary auth/ICV layout differently when ESN is enabled:
the async ahash setup appends a 4-byte seqhi slot before the ICV or
auth_data area, but the async completion callbacks still reconstruct the
temporary layout as if seqhi were absent.
With an async AH implementation selected, that makes AH copy or compare
the wrong bytes on both the IPv4 and IPv6 paths. In UML repro on IPv4 AH
with ESN and forced async hmac(sha1), ping fails with 100% packet loss,
and the callback logs show the pre-fix drift:
ah4 output_done: esn=1 err=0 icv_off=20 expected_off=24
ah4 input_done: esn=1 auth_off=20 expected_auth_off=24 icv_off=32 expected_icv_off=36
Reconstruct the callback-side layout the same way the setup path built it
by skipping the ESN seqhi slot before locating the saved auth_data or ICV.
Per RFC 4302, the ESN high-order 32 bits participate in the AH ICV
computation, so the async callbacks must account for the seqhi slot.
Post-fix, the same IPv4 AH+ESN+forced-async-hmac(sha1) UML repro shows
the corrected offset (ah4 output_done: esn=1 err=0 icv_off=24
expected_off=24) and ping succeeds; net/ipv4/ah4.o and net/ipv6/ah6.o
build clean at W=1. IPv6 AH+ESN was not exercised at runtime, and the
change has not been tested against a real async hardware AH engine. |
| In the Linux kernel, the following vulnerability has been resolved:
fbcon: Avoid OOB font access if console rotation fails
Clear the font buffer if the reallocation during console rotation fails
in fbcon_rotate_font(). The putcs implementations for the rotated buffer
will return early in this case. See [1] for an example.
Currently, fbcon_rotate_font() keeps the old buffer, which is too small
for the rotated font. Printing to the rotated console with a high-enough
character code will overflow the font buffer.
v2:
- fix typos in commit message |
| In the Linux kernel, the following vulnerability has been resolved:
mtd: spi-nor: debugfs: fix out-of-bounds read in spi_nor_params_show()
Sashiko noticed an out-of-bounds read [1].
In spi_nor_params_show(), the snor_f_names array is passed to
spi_nor_print_flags() using sizeof(snor_f_names).
Since snor_f_names is an array of pointers, sizeof() returns the total
number of bytes occupied by the pointers
(element_count * sizeof(void *))
rather than the element count itself. On 64-bit systems, this makes the
passed length 8x larger than intended.
Inside spi_nor_print_flags(), the 'names_len' argument is used to
bounds-check the 'names' array access. An out-of-bounds read occurs
if a flag bit is set that exceeds the array's actual element count
but is within the inflated byte-size count.
Correct this by using ARRAY_SIZE() to pass the actual number of
string pointers in the array. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rsi: fix kthread lifetime race between self-exit and external-stop
RSI driver use both self-exit(kthread_complete_and_exit) and external-stop
(kthread_stop) when killing a kthread. Generally, kthread_stop() is called
first, and in this case, no particular issues occur.
However, in rare instances where kthread_complete_and_exit() is called
first and then kthread_stop() is called, a UAF occurs because the kthread
object, which has already exited and been freed, is accessed again.
Therefore, to prevent this with minimal modification, you must remove
kthread_stop() and change the code to wait until the self-exit operation
is completed. |
| In the Linux kernel, the following vulnerability has been resolved:
smb/client: fix out-of-bounds read in symlink_data()
Since smb2_check_message() returns success without length validation for
the symlink error response, in symlink_data() it is possible for
iov->iov_len to be smaller than sizeof(struct smb2_err_rsp). If the buffer
only contains the base SMB2 header (64 bytes), accessing
err->ErrorContextCount (at offset 66) or err->ByteCount later in
symlink_data() will cause an out-of-bounds read. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: Fix potential use-after-free issue when stopping watchdog task
Watchdog task might end between send_sig() and kthread_stop() calls, what
results in the use-after-free issue. Fix this by increasing watchdog task
reference count before calling send_sig() and dropping it by switching to
kthread_stop_put(). |
