| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
Input: mms114 - fix touch indexing for MMS134S and MMS136
The MMS134S and MMS136 touch controllers have an event size of 6 bytes
rather than 8 bytes. When __mms114_read_reg() reads the touch data
packet from the device into the touch buffer, the events are packed
tightly at 6-byte intervals. However, the driver iterates through the
events using standard C array indexing (touch[index]), where each
element is sizeof(struct mms114_touch) (8 bytes) apart. As a result, any
touch events beyond the first one are read from incorrect offsets and
parsed improperly.
Fix this by explicitly calculating the byte offset for each touch event
based on the device's specific event size. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: iforce - bound the device-reported force-feedback effect index
iforce_process_packet() handles a status report (packet id 0x02) by
taking a force-feedback effect index straight from the device wire and
using it to address the per-effect state array:
i = data[1] & 0x7f;
if (data[1] & 0x80) {
if (!test_and_set_bit(FF_CORE_IS_PLAYED,
iforce->core_effects[i].flags))
...
} else if (test_and_clear_bit(FF_CORE_IS_PLAYED,
iforce->core_effects[i].flags)) {
...
}
The index is masked only with 0x7f, so it ranges 0..127, but
core_effects[] holds only IFORCE_EFFECTS_MAX (32) entries. For an index
of 32..127 the test_and_set_bit()/test_and_clear_bit() is an
out-of-bounds single-bit read-modify-write past the array. core_effects[]
is the second-to-last member of struct iforce, so the write lands in the
trailing members and beyond the embedding kzalloc()'d iforce_serio /
iforce_usb object.
data[1] is unvalidated device payload on both transports (the USB
interrupt endpoint and serio), and the status path is not gated on force
feedback being present, so a malicious or counterfeit device can set or
clear a bit at an attacker-chosen offset past the object.
Reject an out-of-range index instead of indexing with it. Bound against
the array dimension IFORCE_EFFECTS_MAX rather than dev->ff->max_effects so
the check guarantees memory safety regardless of how many effects the
device registered. A legitimate "effect started/stopped" status always
carries an index below IFORCE_EFFECTS_MAX, so well-formed devices are
unaffected; the neighbouring mark_core_as_ready() loop is already bounded
and is left untouched. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: goodix - clamp the device-reported contact count
goodix_ts_read_input_report() copies the number of touch points reported
by the device into an on-stack buffer
u8 point_data[2 + GOODIX_MAX_CONTACT_SIZE * GOODIX_MAX_CONTACTS];
which is sized for at most GOODIX_MAX_CONTACTS (10) contacts. The only
runtime check bounds the per-interrupt count against ts->max_touch_num,
but that value is taken verbatim from a 4-bit field of the device
configuration block and is never clamped:
ts->max_touch_num = ts->config[MAX_CONTACTS_LOC] & 0x0f;
The nibble can be 0..15, so a malfunctioning, malicious or counterfeit
controller (or an attacker tampering with the I2C bus) can advertise up
to 15 contacts. goodix_ts_read_input_report() then accepts a touch_num
of up to 15 and the second goodix_i2c_read() writes
ts->contact_size * (touch_num - 1) bytes past the one-contact header into
point_data - up to 30 bytes (45 with the 9-byte report format) beyond the
92-byte buffer: a stack out-of-bounds write.
Clamp max_touch_num to GOODIX_MAX_CONTACTS, the number of contacts
point_data[] is sized for, when reading it from the configuration. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: synaptics-rmi4 - bound the F30 keymap to the GPIO/LED count
rmi_f30_map_gpios() allocates gpioled_key_map with
min(gpioled_count, TRACKSTICK_RANGE_END) == at most 6 entries, but
rmi_f30_attention() iterates the full f30->gpioled_count (device query
register, range 0..31) and dereferences gpioled_key_map[i], and
input->keycodemax is set to the full gpioled_count while input->keycode
points at the 6-entry allocation.
A device that reports gpioled_count > 6 with GPIO support enabled
therefore causes an out-of-bounds read on the attention interrupt and
out-of-bounds read/write through the EVIOCGKEYCODE/EVIOCSKEYCODE ioctls,
which bound the index only against keycodemax. This is the same defect
as the F3A handler, which was copied from F30.
Size the keymap for the full gpioled_count; the mapping loop still
assigns only the first min(gpioled_count, TRACKSTICK_RANGE_END) entries. |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: imx-lpi2c: mark I2C adapter when hardware is powered down
On some i.MX platforms, certain I2C client drivers keep a periodic
workqueue which continues to trigger I2C transfers.
During system suspend/resume, there exists a time window between:
- suspend_noirq and the system entering suspend
- the system starting to resume and resume_noirq
In this window, the I2C controller resources such as clock and pinctrl
may already be disabled or not yet restored.
If a workqueue triggers an I2C transfer in this period, the driver
attempts to access I2C registers while the hardware resources are
unavailable, which may lead to system hang.
Mark the I2C adapter as suspended during noirq suspend and block new
transfers until resume, ensuring that I2C transfers are only issued
when hardware resources are available. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: arm64: Clear __hyp_running_vcpu when flushing the pKVM hyp vCPU
flush_hyp_vcpu() copies the host vCPU context into the hyp's private
vCPU on every run. ctxt_to_vcpu() expects a guest context to have a
NULL __hyp_running_vcpu, which is only ever set on the host context, so
that it resolves the vCPU via container_of(). While this is generally
the case, flush_hyp_vcpu() copies the context verbatim and does not
enforce this, so a value provided by the host is dereferenced at EL2
(host -> EL2).
Fix by clearing __hyp_running_vcpu after the copy. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/damon/sysfs-schemes: delete tried region in regions_rmdirs()
DAMON sysfs maintains the DAMOS tried region directory objects via a
linked list. When the user requests refresh of the directories, DAMON
sysfs removes all the region directories first, and then generate updated
regions directory on the empty space. The removal function
(damon_sysfs_scheme_regions_rm_dirs()) only puts the kobj objects.
Deletion of the container region object from the linked list is done
inside the kobj release callback function.
If somehow the callback invocation is delayed, the list will contain
regions list that gonna be freed. If the updated region directories
creation is started in this situation, the list can be corrupted and
use-after-free can happen.
Because the kobj objects are managed by only DAMON sysfs, the issue cannot
happen in normal situation. But, such delays can be made on kernels that
built with CONFIG_DEBUG_KOBJECT_RELEASE. On the kernel, the issue can
indeed be reproduced like below.
# damo start --damos_action stat
# cd /sys/kernel/mm/damon/admin/kdamonds/0/
# for i in {1..10}; do echo update_schemes_tried_regions > state; done
# dmesg | grep underflow
[ 89.296152] refcount_t: underflow; use-after-free.
Fix the issue by removing the region object from the list when
decrementing the reference count.
Also update damos_sysfs_populate_region_dir() to add the region object to
the list only after the kobject_init_and_add() is success, so that fail of
kobject_init_and_add() is not leaving the deallocated object on the list.
The issue was discovered [1] by Sashiko. |
| In the Linux kernel, the following vulnerability has been resolved:
media: rc: igorplugusb: fix control request setup packet
Commit eac69475b01f ("media: rc: igorplugusb: heed coherency
rules") changed the control request storage from an embedded struct to
an allocated pointer so it can obey DMA coherency rules.
However, the driver still passes &ir->request to usb_fill_control_urb().
That points the URB setup packet at the pointer field itself rather than
at the allocated struct usb_ctrlrequest.
USB core then interprets pointer bytes as the setup packet. This can
produce an invalid bRequestType and trigger the control direction warning
reported by syzbot:
usb 2-1: BOGUS control dir, pipe 80003580 doesn't match bRequestType 0
Pass ir->request itself as the setup packet. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: net2280: Fix double free in probe error path
usb_initialize_gadget() installs gadget_release() as the release
callback for the embedded gadget device. The struct net2280 instance is
therefore released through gadget_release() when the gadget device's last
reference is dropped.
The probe error path calls net2280_remove(), which tears down the
partially initialized device and drops the gadget reference with
usb_put_gadget(). Calling kfree(dev) afterwards can free the same object
again.
Drop the explicit kfree() and let the gadget device release callback
handle the final free. This issue was found by a static analysis tool
I am developing. |
| In the Linux kernel, the following vulnerability has been resolved:
gpio: rockchip: teardown bugs and resource leaks
Address several teardown issues and resource leaks in the driver's remove
path and error handling:
1. Debounce clock reference leak: The debounce clock (bank->db_clk) is
obtained using of_clk_get() which increments the clock's reference
count, but clk_put() is never called. Register a devm action to
cleanly release it on unbind. Note that of_clk_get(..., 1) remains
necessary over devm_clk_get() because the DT binding does not define
clock-names, precluding name-based lookup.
2. Unregistered chained IRQ handler: The chained IRQ handler is not
disconnected in remove(). If a stray interrupt fires after the driver
is removed, the kernel attempts to execute a stale handler, leading
to a panic. Fix this by clearing the handler in remove().
3. IRQ domain leak: The linear IRQ domain and its generic chips are
allocated manually during probe but never removed. Remove the IRQ
domain during driver teardown to free the associated generic chips
and mappings.
[Bartosz: don't emit an error message on devres allocation failure] |
| In the Linux kernel, the following vulnerability has been resolved:
net: psp: require admin permission for dev-set and key-rotate
The dev-set and key-rotate netlink operations modify shared device
state (PSP version configuration and cryptographic key material,
respectively) but do not require CAP_NET_ADMIN. The only access
control is psp_dev_check_access() which merely verifies netns
membership. |
| In the Linux kernel, the following vulnerability has been resolved:
macvlan: fix macvlan_get_size() not reserving space for IFLA_MACVLAN_BC_CUTOFF
macvlan_get_size() does not account for IFLA_MACVLAN_BC_CUTOFF, but
macvlan_fill_info() conditionally includes it when port->bc_cutoff != 1.
This causes nla_put_s32() to fail with -EMSGSIZE when the netlink skb
runs out of space, triggering a WARN_ON in rtnetlink and preventing the
interface from being dumped.
The bug can be reproduced with:
ip link add macvlan0 link eth0 type macvlan mode bridge
ip link set macvlan0 type macvlan bc_cutoff 0
ip -d link show macvlan0 # fails with -EMSGSIZE
The bc_cutoff feature was added in commit 954d1fa1ac93 ("macvlan: Add
netlink attribute for broadcast cutoff"), which added the nla_put_s32()
call in macvlan_fill_info() but missed adding the corresponding
nla_total_size(4) in macvlan_get_size(). A follow-up commit
55cef78c244d ("macvlan: add forgotten nla_policy for
IFLA_MACVLAN_BC_CUTOFF") fixed the missing nla_policy entry but still
did not fix the size calculation. |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: core: fix adapter deregistration race
Adapters can be looked up by their id using i2c_get_adapter() which
takes a reference to the embedded struct device.
Remove the adapter from the IDR before tearing it down during
deregistration (and on registration failure) to make sure its resources
are not accessed after having been freed (e.g. the device name). |
| In the Linux kernel, the following vulnerability has been resolved:
fpga: dfl-afu: validate DMA mapping length in afu_dma_map_region()
afu_ioctl_dma_map() accepts a 64-bit length from userspace via
DFL_FPGA_PORT_DMA_MAP ioctl without an upper bound check. The value
is passed to afu_dma_pin_pages() where npages is derived as
length >> PAGE_SHIFT and passed to pin_user_pages_fast() which takes
int nr_pages, causing implicit truncation if length is very large.
Validate map.length at the ioctl entry point before calling
afu_dma_map_region(), rejecting values whose page count exceeds
INT_MAX. |
| In the Linux kernel, the following vulnerability has been resolved:
svcrdma: wake sq waiters when the transport closes
Threads parked in svc_rdma_sq_wait() on sc_sq_ticket_wait or
sc_send_wait can hang indefinitely in TASK_UNINTERRUPTIBLE state
across transport teardown, pinning svc_xprt references and
blocking svc_rdma_free().
The close path sets XPT_CLOSE before invoking xpo_detach and both
wait_event predicates include an XPT_CLOSE term, but the
predicates are re-evaluated only on wakeup. sc_sq_ticket_wait has
no completion-driven wake path; it is advanced solely by the
chained ticket handoff inside svc_rdma_sq_wait() itself. Without
an explicit wake at close, parked threads never observe
XPT_CLOSE, hold their svc_xprt_get reference forever, and
svc_rdma_free() blocks on xpt_ref dropping to zero.
Two close entry points reach this transport. Local teardown runs
svc_rdma_detach() from svc_handle_xprt() -> svc_delete_xprt() ->
xpo_detach() on a worker thread. A remote disconnect arrives at
svc_rdma_cma_handler(), which calls svc_xprt_deferred_close():
that sets XPT_CLOSE and enqueues the transport but does not
access either RDMA waitqueue, so a worker already parked in
svc_rdma_sq_wait() never re-evaluates its predicate. With every
worker parked on this transport, no thread is available to run
the local teardown either, and the wake site there is
unreachable.
Introduce svc_rdma_xprt_deferred_close(), a thin svcrdma wrapper
that calls svc_xprt_deferred_close() and then wakes both
sc_sq_ticket_wait and sc_send_wait. Convert the svcrdma producers
that called svc_xprt_deferred_close() directly:
svc_rdma_cma_handler(), qp_event_handler(),
svc_rdma_post_send_err(), svc_rdma_wc_send(), the sendto drop
path, the rw completion error paths, and the recvfrom flush and
read-list error paths.
Wake both waitqueues from svc_rdma_detach() as well. The
synchronous svc_xprt_close() path (backchannel ENOTCONN, device
removal via svc_rdma_xprt_done) reaches detach without flowing
through svc_xprt_deferred_close() and therefore does not invoke
the new helper.
[ cel: add svc_rdma_xprt_deferred_close() to complete the fix ] |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: arm64: Don't leak PFN when kvm_translate_vncr() races MMU notifier
In the case that kvm_translate_vncr() races with an MMU notifier the
early return does not release a reference on the faulted in PFN. Add
the necessary call to kvm_release_faultin_page() for the unused PFN. |
| In the Linux kernel, the following vulnerability has been resolved:
idpf: fix read_dev_clk_lock spinlock init in idpf_ptp_init()
In idpf_ptp_init(), read_dev_clk_lock is initialized after
ptp_schedule_worker() had already been called (and after
idpf_ptp_settime64() could reach the lock). The PTP aux worker
fires immediately upon scheduling and can call into
idpf_ptp_read_src_clk_reg_direct(), which takes
spin_lock(&ptp->read_dev_clk_lock) on an uninitialized lock, triggering
the lockdep "non-static key" warning:
[12973.796587] idpf 0000:83:00.0: Device HW Reset initiated
[12974.094507] INFO: trying to register non-static key.
...
[12974.097208] Call Trace:
[12974.097213] <TASK>
[12974.097218] dump_stack_lvl+0x93/0xe0
[12974.097234] register_lock_class+0x4c4/0x4e0
[12974.097249] ? __lock_acquire+0x427/0x2290
[12974.097259] __lock_acquire+0x98/0x2290
[12974.097272] lock_acquire+0xc6/0x310
[12974.097281] ? idpf_ptp_read_src_clk_reg+0xb7/0x150 [idpf]
[12974.097311] ? lockdep_hardirqs_on_prepare+0xde/0x190
[12974.097318] ? finish_task_switch.isra.0+0xd2/0x350
[12974.097330] ? __pfx_ptp_aux_kworker+0x10/0x10 [ptp]
[12974.097343] _raw_spin_lock+0x30/0x40
[12974.097353] ? idpf_ptp_read_src_clk_reg+0xb7/0x150 [idpf]
[12974.097373] idpf_ptp_read_src_clk_reg+0xb7/0x150 [idpf]
[12974.097391] ? kthread_worker_fn+0x88/0x3d0
[12974.097404] ? kthread_worker_fn+0x4e/0x3d0
[12974.097411] idpf_ptp_update_cached_phctime+0x26/0x120 [idpf]
[12974.097428] ? _raw_spin_unlock_irq+0x28/0x50
[12974.097436] idpf_ptp_do_aux_work+0x15/0x20 [idpf]
[12974.097454] ptp_aux_kworker+0x20/0x40 [ptp]
[12974.097464] kthread_worker_fn+0xd5/0x3d0
[12974.097474] ? __pfx_kthread_worker_fn+0x10/0x10
[12974.097482] kthread+0xf4/0x130
[12974.097489] ? __pfx_kthread+0x10/0x10
[12974.097498] ret_from_fork+0x32c/0x410
[12974.097512] ? __pfx_kthread+0x10/0x10
[12974.097519] ret_from_fork_asm+0x1a/0x30
[12974.097540] </TASK>
Move the call to spin_lock_init() up a bit to make sure read_dev_clk_lock
is not touched before it's been initialized. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ti: icssm-prueth: fix eth_ports_node leak in probe
The error path on of_property_read_u32() failure inside
icssm_prueth_probe() returns without putting eth_ports_node,
which was acquired before the for_each_child_of_node() loop.
Drop it before returning. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: tracepoints: fix sleep while in atomic context in btrfs_sync_file()
The trace event btrfs_sync_file() is called in an atomic context (all trace
events are) and its call to dput(), which is needed due to the call to
dget_parent(), can sleep, triggering a kernel splat.
This can be reproduced by enabling the trace event and running btrfs/056
from fstests for example. The splat shown in dmesg is the following:
[53.919] BUG: sleeping function called from invalid context at fs/dcache.c:970
[53.947] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 32773, name: xfs_io
[53.988] preempt_count: 2, expected: 0
[53.967] RCU nest depth: 0, expected: 0
[53.943] Preemption disabled at:
[53.944] [<0000000000000000>] 0x0
[54.078] CPU: 0 UID: 0 PID: 32773 Comm: xfs_io Tainted: G W 7.1.0-rc1-btrfs-next-232+ #1 PREEMPT(full)
[54.070] Tainted: [W]=WARN
[54.071] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.2-0-gea1b7a073390-prebuilt.qemu.org 04/01/2014
[54.072] Call Trace:
[54.074] <TASK>
[54.076] dump_stack_lvl+0x56/0x80
[54.079] __might_resched.cold+0xd6/0x10f
[54.072] dput.part.0+0x24/0x110
[54.078] trace_event_raw_event_btrfs_sync_file+0x75/0x140 [btrfs]
[54.089] btrfs_sync_file+0x1ed/0x530 [btrfs]
[54.087] ? __handle_mm_fault+0x8ae/0xed0
[54.089] btrfs_do_write_iter+0x172/0x210 [btrfs]
[54.091] vfs_write+0x21f/0x450
[54.094] __x64_sys_pwrite64+0x8d/0xc0
[54.096] ? do_user_addr_fault+0x20c/0x670
[54.099] do_syscall_64+0x60/0xf20
[54.092] ? clear_bhb_loop+0x60/0xb0
[54.094] entry_SYSCALL_64_after_hwframe+0x76/0x7e
So stop using dget_parent() and dput() and access the parent dentry
directly as dentry->d_parent. This is also what ext4 is doing in
its equivalent trace event ext4_sync_file_enter(). |
| In the Linux kernel, the following vulnerability has been resolved:
test_kprobes: clear kprobes between test runs
Running the kprobes sanity tests twice makes all tests fail and
eventually crashes the kernel.
[root@martin-riscv-1 ~]# echo 1 > /sys/kernel/debug/kunit/kprobes_test/run
...
# Totals: pass:5 fail:0 skip:0 total:5
ok 1 kprobes_test
[root@martin-riscv-1 ~]# echo 1 > /sys/kernel/debug/kunit/kprobes_test/run
...
# test_kprobe: EXPECTATION FAILED at lib/tests/test_kprobes.c:64
Expected 0 == register_kprobe(&kp), but
register_kprobe(&kp) == -22 (0xffffffffffffffea)
...
Unable to handle kernel paging request ...
The testsuite defines several kprobes and kretprobes as static variables
that are preserved across test runs.
After register_kprobe and unregister_kprobe, a kprobe contains some
leftover data that must be cleared before the kprobe can be registered
again. The tests are setting symbol_name to define the probe location.
Address and flags must be cleared.
The existing code clears some of the probes between subsequent tests, but
not between two test runs. The leftover data from a previous test run
makes the registrations fail in the next run.
Move the cleanups for all kprobes into kprobes_test_init, this function
is called before each single test (including the first test of a test
run). |
