| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7921: fix skb leak by txs missing in AMSDU
txs may be dropped if the frame is aggregated in AMSDU. When the problem
shows up, some SKBs would be hold in driver to cause network stopped
temporarily. Even if the problem can be recovered by txs timeout handling,
mt7921 still need to disable txs in AMSDU to avoid this issue. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: pcie: fix possible NULL pointer dereference
It is possible that iwl_pci_probe() will fail and free the trans,
then afterwards iwl_pci_remove() will be called and crash by trying
to access trans which is already freed, fix it.
iwlwifi 0000:01:00.0: Detected crf-id 0xa5a5a5a2, cnv-id 0xa5a5a5a2
wfpm id 0xa5a5a5a2
iwlwifi 0000:01:00.0: Can't find a correct rfid for crf id 0x5a2
...
BUG: kernel NULL pointer dereference, address: 0000000000000028
...
RIP: 0010:iwl_pci_remove+0x12/0x30 [iwlwifi]
pci_device_remove+0x3e/0xb0
device_release_driver_internal+0x103/0x1f0
driver_detach+0x4c/0x90
bus_remove_driver+0x5c/0xd0
driver_unregister+0x31/0x50
pci_unregister_driver+0x40/0x90
iwl_pci_unregister_driver+0x15/0x20 [iwlwifi]
__exit_compat+0x9/0x98 [iwlwifi]
__x64_sys_delete_module+0x147/0x260 |
| In the Linux kernel, the following vulnerability has been resolved:
net: core: prevent NULL deref in generic_hwtstamp_ioctl_lower()
The ethtool tsconfig Netlink path can trigger a null pointer
dereference. A call chain such as:
tsconfig_prepare_data() ->
dev_get_hwtstamp_phylib() ->
vlan_hwtstamp_get() ->
generic_hwtstamp_get_lower() ->
generic_hwtstamp_ioctl_lower()
results in generic_hwtstamp_ioctl_lower() being called with
kernel_cfg->ifr as NULL.
The generic_hwtstamp_ioctl_lower() function does not expect
a NULL ifr and dereferences it, leading to a system crash.
Fix this by adding a NULL check for kernel_cfg->ifr in
generic_hwtstamp_ioctl_lower(). If ifr is NULL, return -EINVAL. |
| In the Linux kernel, the following vulnerability has been resolved:
kheaders: Use array declaration instead of char
Under CONFIG_FORTIFY_SOURCE, memcpy() will check the size of destination
and source buffers. Defining kernel_headers_data as "char" would trip
this check. Since these addresses are treated as byte arrays, define
them as arrays (as done everywhere else).
This was seen with:
$ cat /sys/kernel/kheaders.tar.xz >> /dev/null
detected buffer overflow in memcpy
kernel BUG at lib/string_helpers.c:1027!
...
RIP: 0010:fortify_panic+0xf/0x20
[...]
Call Trace:
<TASK>
ikheaders_read+0x45/0x50 [kheaders]
kernfs_fop_read_iter+0x1a4/0x2f0
... |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/guc: Fix stack_depot usage
Add missing stack_depot_init() call when CONFIG_DRM_XE_DEBUG_GUC is
enabled to fix the following call stack:
[] BUG: kernel NULL pointer dereference, address: 0000000000000000
[] Workqueue: drm_sched_run_job_work [gpu_sched]
[] RIP: 0010:stack_depot_save_flags+0x172/0x870
[] Call Trace:
[] <TASK>
[] fast_req_track+0x58/0xb0 [xe]
(cherry picked from commit 64fdf496a6929a0a194387d2bb5efaf5da2b542f) |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Fix WARN_ON in tracing_buffers_mmap_close for split VMAs
When a VMA is split (e.g., by partial munmap or MAP_FIXED), the kernel
calls vm_ops->close on each portion. For trace buffer mappings, this
results in ring_buffer_unmap() being called multiple times while
ring_buffer_map() was only called once.
This causes ring_buffer_unmap() to return -ENODEV on subsequent calls
because user_mapped is already 0, triggering a WARN_ON.
Trace buffer mappings cannot support partial mappings because the ring
buffer structure requires the complete buffer including the meta page.
Fix this by adding a may_split callback that returns -EINVAL to prevent
VMA splits entirely. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath12k: Fix memory leak in rx_desc and tx_desc
Currently when ath12k_dp_cc_desc_init() is called we allocate
memory to rx_descs and tx_descs. In ath12k_dp_cc_cleanup(), during
descriptor cleanup rx_descs and tx_descs memory is not freed.
This is cause of memory leak. These allocated memory should be
freed in ath12k_dp_cc_cleanup.
In ath12k_dp_cc_desc_init(), we can save base address of rx_descs
and tx_descs. In ath12k_dp_cc_cleanup(), we can free rx_descs and
tx_descs memory using their base address.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 |
| In the Linux kernel, the following vulnerability has been resolved:
sched_ext: Fix scx_enable() crash on helper kthread creation failure
A crash was observed when the sched_ext selftests runner was
terminated with Ctrl+\ while test 15 was running:
NIP [c00000000028fa58] scx_enable.constprop.0+0x358/0x12b0
LR [c00000000028fa2c] scx_enable.constprop.0+0x32c/0x12b0
Call Trace:
scx_enable.constprop.0+0x32c/0x12b0 (unreliable)
bpf_struct_ops_link_create+0x18c/0x22c
__sys_bpf+0x23f8/0x3044
sys_bpf+0x2c/0x6c
system_call_exception+0x124/0x320
system_call_vectored_common+0x15c/0x2ec
kthread_run_worker() returns an ERR_PTR() on failure rather than NULL,
but the current code in scx_alloc_and_add_sched() only checks for a NULL
helper. Incase of failure on SIGQUIT, the error is not handled in
scx_alloc_and_add_sched() and scx_enable() ends up dereferencing an
error pointer.
Error handling is fixed in scx_alloc_and_add_sched() to propagate
PTR_ERR() into ret, so that scx_enable() jumps to the existing error
path, avoiding random dereference on failure. |
| Insufficient control flow management in the Linux kernel-mode driver for some Intel(R) 800 Series Ethernet before version 1.17.2 may allow an authenticated user to potentially enable escalation of privilege via local access. |
| In the Linux kernel, the following vulnerability has been resolved:
kcsan: Avoid READ_ONCE() in read_instrumented_memory()
Haibo Li reported:
| Unable to handle kernel paging request at virtual address
| ffffff802a0d8d7171
| Mem abort info:o:
| ESR = 0x9600002121
| EC = 0x25: DABT (current EL), IL = 32 bitsts
| SET = 0, FnV = 0 0
| EA = 0, S1PTW = 0 0
| FSC = 0x21: alignment fault
| Data abort info:o:
| ISV = 0, ISS = 0x0000002121
| CM = 0, WnR = 0 0
| swapper pgtable: 4k pages, 39-bit VAs, pgdp=000000002835200000
| [ffffff802a0d8d71] pgd=180000005fbf9003, p4d=180000005fbf9003,
| pud=180000005fbf9003, pmd=180000005fbe8003, pte=006800002a0d8707
| Internal error: Oops: 96000021 [#1] PREEMPT SMP
| Modules linked in:
| CPU: 2 PID: 45 Comm: kworker/u8:2 Not tainted
| 5.15.78-android13-8-g63561175bbda-dirty #1
| ...
| pc : kcsan_setup_watchpoint+0x26c/0x6bc
| lr : kcsan_setup_watchpoint+0x88/0x6bc
| sp : ffffffc00ab4b7f0
| x29: ffffffc00ab4b800 x28: ffffff80294fe588 x27: 0000000000000001
| x26: 0000000000000019 x25: 0000000000000001 x24: ffffff80294fdb80
| x23: 0000000000000000 x22: ffffffc00a70fb68 x21: ffffff802a0d8d71
| x20: 0000000000000002 x19: 0000000000000000 x18: ffffffc00a9bd060
| x17: 0000000000000001 x16: 0000000000000000 x15: ffffffc00a59f000
| x14: 0000000000000001 x13: 0000000000000000 x12: ffffffc00a70faa0
| x11: 00000000aaaaaaab x10: 0000000000000054 x9 : ffffffc00839adf8
| x8 : ffffffc009b4cf00 x7 : 0000000000000000 x6 : 0000000000000007
| x5 : 0000000000000000 x4 : 0000000000000000 x3 : ffffffc00a70fb70
| x2 : 0005ff802a0d8d71 x1 : 0000000000000000 x0 : 0000000000000000
| Call trace:
| kcsan_setup_watchpoint+0x26c/0x6bc
| __tsan_read2+0x1f0/0x234
| inflate_fast+0x498/0x750
| zlib_inflate+0x1304/0x2384
| __gunzip+0x3a0/0x45c
| gunzip+0x20/0x30
| unpack_to_rootfs+0x2a8/0x3fc
| do_populate_rootfs+0xe8/0x11c
| async_run_entry_fn+0x58/0x1bc
| process_one_work+0x3ec/0x738
| worker_thread+0x4c4/0x838
| kthread+0x20c/0x258
| ret_from_fork+0x10/0x20
| Code: b8bfc2a8 2a0803f7 14000007 d503249f (78bfc2a8) )
| ---[ end trace 613a943cb0a572b6 ]-----
The reason for this is that on certain arm64 configuration since
e35123d83ee3 ("arm64: lto: Strengthen READ_ONCE() to acquire when
CONFIG_LTO=y"), READ_ONCE() may be promoted to a full atomic acquire
instruction which cannot be used on unaligned addresses.
Fix it by avoiding READ_ONCE() in read_instrumented_memory(), and simply
forcing the compiler to do the required access by casting to the
appropriate volatile type. In terms of generated code this currently
only affects architectures that do not use the default READ_ONCE()
implementation.
The only downside is that we are not guaranteed atomicity of the access
itself, although on most architectures a plain load up to machine word
size should still be atomic (a fact the default READ_ONCE() still relies
on itself). |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: cadence: cdns_i2c_master_xfer(): Fix runtime PM leak on error path
The cdns_i2c_master_xfer() function gets a runtime PM reference when the
function is entered. This reference is released when the function is
exited. There is currently one error path where the function exits
directly, which leads to a leak of the runtime PM reference.
Make sure that this error path also releases the runtime PM reference. |
| In the Linux kernel, the following vulnerability has been resolved:
tty: serial: sh-sci: fix RSCI FIFO overrun handling
The receive error handling code is shared between RSCI and all other
SCIF port types, but the RSCI overrun_reg is specified as a memory
offset, while for other SCIF types it is an enum value used to index
into the sci_port_params->regs array, as mentioned above the
sci_serial_in() function.
For RSCI, the overrun_reg is CSR (0x48), causing the sci_getreg() call
inside the sci_handle_fifo_overrun() function to index outside the
bounds of the regs array, which currently has a size of 20, as specified
by SCI_NR_REGS.
Because of this, we end up accessing memory outside of RSCI's
rsci_port_params structure, which, when interpreted as a plat_sci_reg,
happens to have a non-zero size, causing the following WARN when
sci_serial_in() is called, as the accidental size does not match the
supported register sizes.
The existence of the overrun_reg needs to be checked because
SCIx_SH3_SCIF_REGTYPE has overrun_reg set to SCLSR, but SCLSR is not
present in the regs array.
Avoid calling sci_getreg() for port types which don't use standard
register handling.
Use the ops->read_reg() and ops->write_reg() functions to properly read
and write registers for RSCI, and change the type of the status variable
to accommodate the 32-bit CSR register.
sci_getreg() and sci_serial_in() are also called with overrun_reg in the
sci_mpxed_interrupt() interrupt handler, but that code path is not used
for RSCI, as it does not have a muxed interrupt.
------------[ cut here ]------------
Invalid register access
WARNING: CPU: 0 PID: 0 at drivers/tty/serial/sh-sci.c:522 sci_serial_in+0x38/0xac
Modules linked in: renesas_usbhs at24 rzt2h_adc industrialio_adc sha256 cfg80211 bluetooth ecdh_generic ecc rfkill fuse drm backlight ipv6
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.17.0-rc1+ #30 PREEMPT
Hardware name: Renesas RZ/T2H EVK Board based on r9a09g077m44 (DT)
pstate: 604000c5 (nZCv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : sci_serial_in+0x38/0xac
lr : sci_serial_in+0x38/0xac
sp : ffff800080003e80
x29: ffff800080003e80 x28: ffff800082195b80 x27: 000000000000000d
x26: ffff8000821956d0 x25: 0000000000000000 x24: ffff800082195b80
x23: ffff000180e0d800 x22: 0000000000000010 x21: 0000000000000000
x20: 0000000000000010 x19: ffff000180e72000 x18: 000000000000000a
x17: ffff8002bcee7000 x16: ffff800080000000 x15: 0720072007200720
x14: 0720072007200720 x13: 0720072007200720 x12: 0720072007200720
x11: 0000000000000058 x10: 0000000000000018 x9 : ffff8000821a6a48
x8 : 0000000000057fa8 x7 : 0000000000000406 x6 : ffff8000821fea48
x5 : ffff00033ef88408 x4 : ffff8002bcee7000 x3 : ffff800082195b80
x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff800082195b80
Call trace:
sci_serial_in+0x38/0xac (P)
sci_handle_fifo_overrun.isra.0+0x70/0x134
sci_er_interrupt+0x50/0x39c
__handle_irq_event_percpu+0x48/0x140
handle_irq_event+0x44/0xb0
handle_fasteoi_irq+0xf4/0x1a0
handle_irq_desc+0x34/0x58
generic_handle_domain_irq+0x1c/0x28
gic_handle_irq+0x4c/0x140
call_on_irq_stack+0x30/0x48
do_interrupt_handler+0x80/0x84
el1_interrupt+0x34/0x68
el1h_64_irq_handler+0x18/0x24
el1h_64_irq+0x6c/0x70
default_idle_call+0x28/0x58 (P)
do_idle+0x1f8/0x250
cpu_startup_entry+0x34/0x3c
rest_init+0xd8/0xe0
console_on_rootfs+0x0/0x6c
__primary_switched+0x88/0x90
---[ end trace 0000000000000000 ]--- |
| Improper input validation in the Linux kernel-mode driver for some Intel(R) 700 Series Ethernet before version 2.28.5 may allow an authenticated user to potentially enable escalation of privilege. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/damon/sysfs: catch commit test ctx alloc failure
Patch series "mm/damon/sysfs: fix commit test damon_ctx [de]allocation".
DAMON sysfs interface dynamically allocates and uses a damon_ctx object
for testing if given inputs for online DAMON parameters update is valid.
The object is being used without an allocation failure check, and leaked
when the test succeeds. Fix the two bugs.
This patch (of 2):
The damon_ctx for testing online DAMON parameters commit inputs is used
without its allocation failure check. This could result in an invalid
memory access. Fix it by directly returning an error when the allocation
failed. |
| In the Linux kernel, the following vulnerability has been resolved:
io_uring/rw: ensure allocated iovec gets cleared for early failure
A previous commit reused the recyling infrastructure for early cleanup,
but this is not enough for the case where our internal caches have
overflowed. If this happens, then the allocated iovec can get leaked if
the request is also aborted early.
Reinstate the previous forced free of the iovec for that situation. |
| In the Linux kernel, the following vulnerability has been resolved:
af_unix: Fix data-race around unix_tot_inflight.
unix_tot_inflight is changed under spin_lock(unix_gc_lock), but
unix_release_sock() reads it locklessly.
Let's use READ_ONCE() for unix_tot_inflight.
Note that the writer side was marked by commit 9d6d7f1cb67c ("af_unix:
annote lockless accesses to unix_tot_inflight & gc_in_progress")
BUG: KCSAN: data-race in unix_inflight / unix_release_sock
write (marked) to 0xffffffff871852b8 of 4 bytes by task 123 on cpu 1:
unix_inflight+0x130/0x180 net/unix/scm.c:64
unix_attach_fds+0x137/0x1b0 net/unix/scm.c:123
unix_scm_to_skb net/unix/af_unix.c:1832 [inline]
unix_dgram_sendmsg+0x46a/0x14f0 net/unix/af_unix.c:1955
sock_sendmsg_nosec net/socket.c:724 [inline]
sock_sendmsg+0x148/0x160 net/socket.c:747
____sys_sendmsg+0x4e4/0x610 net/socket.c:2493
___sys_sendmsg+0xc6/0x140 net/socket.c:2547
__sys_sendmsg+0x94/0x140 net/socket.c:2576
__do_sys_sendmsg net/socket.c:2585 [inline]
__se_sys_sendmsg net/socket.c:2583 [inline]
__x64_sys_sendmsg+0x45/0x50 net/socket.c:2583
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3b/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x72/0xdc
read to 0xffffffff871852b8 of 4 bytes by task 4891 on cpu 0:
unix_release_sock+0x608/0x910 net/unix/af_unix.c:671
unix_release+0x59/0x80 net/unix/af_unix.c:1058
__sock_release+0x7d/0x170 net/socket.c:653
sock_close+0x19/0x30 net/socket.c:1385
__fput+0x179/0x5e0 fs/file_table.c:321
____fput+0x15/0x20 fs/file_table.c:349
task_work_run+0x116/0x1a0 kernel/task_work.c:179
resume_user_mode_work include/linux/resume_user_mode.h:49 [inline]
exit_to_user_mode_loop kernel/entry/common.c:171 [inline]
exit_to_user_mode_prepare+0x174/0x180 kernel/entry/common.c:204
__syscall_exit_to_user_mode_work kernel/entry/common.c:286 [inline]
syscall_exit_to_user_mode+0x1a/0x30 kernel/entry/common.c:297
do_syscall_64+0x4b/0x90 arch/x86/entry/common.c:86
entry_SYSCALL_64_after_hwframe+0x72/0xdc
value changed: 0x00000000 -> 0x00000001
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 4891 Comm: systemd-coredum Not tainted 6.4.0-rc5-01219-gfa0e21fa4443 #5
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 |
| In the Linux kernel, the following vulnerability has been resolved:
cifs: client: fix memory leak in smb3_fs_context_parse_param
The user calls fsconfig twice, but when the program exits, free() only
frees ctx->source for the second fsconfig, not the first.
Regarding fc->source, there is no code in the fs context related to its
memory reclamation.
To fix this memory leak, release the source memory corresponding to ctx
or fc before each parsing.
syzbot reported:
BUG: memory leak
unreferenced object 0xffff888128afa360 (size 96):
backtrace (crc 79c9c7ba):
kstrdup+0x3c/0x80 mm/util.c:84
smb3_fs_context_parse_param+0x229b/0x36c0 fs/smb/client/fs_context.c:1444
BUG: memory leak
unreferenced object 0xffff888112c7d900 (size 96):
backtrace (crc 79c9c7ba):
smb3_fs_context_fullpath+0x70/0x1b0 fs/smb/client/fs_context.c:629
smb3_fs_context_parse_param+0x2266/0x36c0 fs/smb/client/fs_context.c:1438 |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix deadlock when converting an inline directory in nojournal mode
In no journal mode, ext4_finish_convert_inline_dir() can self-deadlock
by calling ext4_handle_dirty_dirblock() when it already has taken the
directory lock. There is a similar self-deadlock in
ext4_incvert_inline_data_nolock() for data files which we'll fix at
the same time.
A simple reproducer demonstrating the problem:
mke2fs -Fq -t ext2 -O inline_data -b 4k /dev/vdc 64
mount -t ext4 -o dirsync /dev/vdc /vdc
cd /vdc
mkdir file0
cd file0
touch file0
touch file1
attr -s BurnSpaceInEA -V abcde .
touch supercalifragilisticexpialidocious |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: Fix NULL pointer dereference in snd_usb_mixer_controls_badd
In snd_usb_create_streams(), for UAC version 3 devices, the Interface
Association Descriptor (IAD) is retrieved via usb_ifnum_to_if(). If this
call fails, a fallback routine attempts to obtain the IAD from the next
interface and sets a BADD profile. However, snd_usb_mixer_controls_badd()
assumes that the IAD retrieved from usb_ifnum_to_if() is always valid,
without performing a NULL check. This can lead to a NULL pointer
dereference when usb_ifnum_to_if() fails to find the interface descriptor.
This patch adds a NULL pointer check after calling usb_ifnum_to_if() in
snd_usb_mixer_controls_badd() to prevent the dereference.
This issue was discovered by syzkaller, which triggered the bug by sending
a crafted USB device descriptor. |
| In the Linux kernel, the following vulnerability has been resolved:
binder: fix memory leak in binder_init()
In binder_init(), the destruction of binder_alloc_shrinker_init() is not
performed in the wrong path, which will cause memory leaks. So this commit
introduces binder_alloc_shrinker_exit() and calls it in the wrong path to
fix that. |
