| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath9k: avoid referencing uninit memory in ath9k_wmi_ctrl_rx
For the reasons also described in commit b383e8abed41 ("wifi: ath9k: avoid
uninit memory read in ath9k_htc_rx_msg()"), ath9k_htc_rx_msg() should
validate pkt_len before accessing the SKB.
For example, the obtained SKB may have been badly constructed with
pkt_len = 8. In this case, the SKB can only contain a valid htc_frame_hdr
but after being processed in ath9k_htc_rx_msg() and passed to
ath9k_wmi_ctrl_rx() endpoint RX handler, it is expected to have a WMI
command header which should be located inside its data payload.
Implement sanity checking inside ath9k_wmi_ctrl_rx(). Otherwise, uninit
memory can be referenced.
Tested on Qualcomm Atheros Communications AR9271 802.11n .
Found by Linux Verification Center (linuxtesting.org) with Syzkaller. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: 8250_bcm7271: fix leak in `brcmuart_probe`
Smatch reports:
drivers/tty/serial/8250/8250_bcm7271.c:1120 brcmuart_probe() warn:
'baud_mux_clk' from clk_prepare_enable() not released on lines: 1032.
The issue is fixed by using a managed clock. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/irdma: Fix data race on CQP completion stats
CQP completion statistics is read lockesly in irdma_wait_event and
irdma_check_cqp_progress while it can be updated in the completion
thread irdma_sc_ccq_get_cqe_info on another CPU as KCSAN reports.
Make completion statistics an atomic variable to reflect coherent updates
to it. This will also avoid load/store tearing logic bug potentially
possible by compiler optimizations.
[77346.170861] BUG: KCSAN: data-race in irdma_handle_cqp_op [irdma] / irdma_sc_ccq_get_cqe_info [irdma]
[77346.171383] write to 0xffff8a3250b108e0 of 8 bytes by task 9544 on cpu 4:
[77346.171483] irdma_sc_ccq_get_cqe_info+0x27a/0x370 [irdma]
[77346.171658] irdma_cqp_ce_handler+0x164/0x270 [irdma]
[77346.171835] cqp_compl_worker+0x1b/0x20 [irdma]
[77346.172009] process_one_work+0x4d1/0xa40
[77346.172024] worker_thread+0x319/0x700
[77346.172037] kthread+0x180/0x1b0
[77346.172054] ret_from_fork+0x22/0x30
[77346.172136] read to 0xffff8a3250b108e0 of 8 bytes by task 9838 on cpu 2:
[77346.172234] irdma_handle_cqp_op+0xf4/0x4b0 [irdma]
[77346.172413] irdma_cqp_aeq_cmd+0x75/0xa0 [irdma]
[77346.172592] irdma_create_aeq+0x390/0x45a [irdma]
[77346.172769] irdma_rt_init_hw.cold+0x212/0x85d [irdma]
[77346.172944] irdma_probe+0x54f/0x620 [irdma]
[77346.173122] auxiliary_bus_probe+0x66/0xa0
[77346.173137] really_probe+0x140/0x540
[77346.173154] __driver_probe_device+0xc7/0x220
[77346.173173] driver_probe_device+0x5f/0x140
[77346.173190] __driver_attach+0xf0/0x2c0
[77346.173208] bus_for_each_dev+0xa8/0xf0
[77346.173225] driver_attach+0x29/0x30
[77346.173240] bus_add_driver+0x29c/0x2f0
[77346.173255] driver_register+0x10f/0x1a0
[77346.173272] __auxiliary_driver_register+0xbc/0x140
[77346.173287] irdma_init_module+0x55/0x1000 [irdma]
[77346.173460] do_one_initcall+0x7d/0x410
[77346.173475] do_init_module+0x81/0x2c0
[77346.173491] load_module+0x1232/0x12c0
[77346.173506] __do_sys_finit_module+0x101/0x180
[77346.173522] __x64_sys_finit_module+0x3c/0x50
[77346.173538] do_syscall_64+0x39/0x90
[77346.173553] entry_SYSCALL_64_after_hwframe+0x63/0xcd
[77346.173634] value changed: 0x0000000000000094 -> 0x0000000000000095 |
| In the Linux kernel, the following vulnerability has been resolved:
ptp_qoriq: fix memory leak in probe()
Smatch complains that:
drivers/ptp/ptp_qoriq.c ptp_qoriq_probe()
warn: 'base' from ioremap() not released.
Fix this by revising the parameter from 'ptp_qoriq->base' to 'base'.
This is only a bug if ptp_qoriq_init() returns on the
first -ENODEV error path.
For other error paths ptp_qoriq->base and base are the same.
And this change makes the code more readable. |
| In the Linux kernel, the following vulnerability has been resolved:
ovl: fix null pointer dereference in ovl_get_acl_rcu()
Following process:
P1 P2
path_openat
link_path_walk
may_lookup
inode_permission(rcu)
ovl_permission
acl_permission_check
check_acl
get_cached_acl_rcu
ovl_get_inode_acl
realinode = ovl_inode_real(ovl_inode)
drop_cache
__dentry_kill(ovl_dentry)
iput(ovl_inode)
ovl_destroy_inode(ovl_inode)
dput(oi->__upperdentry)
dentry_kill(upperdentry)
dentry_unlink_inode
upperdentry->d_inode = NULL
ovl_inode_upper
upperdentry = ovl_i_dentry_upper(ovl_inode)
d_inode(upperdentry) // returns NULL
IS_POSIXACL(realinode) // NULL pointer dereference
, will trigger an null pointer dereference at realinode:
[ 205.472797] BUG: kernel NULL pointer dereference, address:
0000000000000028
[ 205.476701] CPU: 2 PID: 2713 Comm: ls Not tainted
6.3.0-12064-g2edfa098e750-dirty #1216
[ 205.478754] RIP: 0010:do_ovl_get_acl+0x5d/0x300
[ 205.489584] Call Trace:
[ 205.489812] <TASK>
[ 205.490014] ovl_get_inode_acl+0x26/0x30
[ 205.490466] get_cached_acl_rcu+0x61/0xa0
[ 205.490908] generic_permission+0x1bf/0x4e0
[ 205.491447] ovl_permission+0x79/0x1b0
[ 205.491917] inode_permission+0x15e/0x2c0
[ 205.492425] link_path_walk+0x115/0x550
[ 205.493311] path_lookupat.isra.0+0xb2/0x200
[ 205.493803] filename_lookup+0xda/0x240
[ 205.495747] vfs_fstatat+0x7b/0xb0
Fetch a reproducer in [Link].
Use the helper ovl_i_path_realinode() to get realinode and then do
non-nullptr checking. |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/powernv/sriov: perform null check on iov before dereferencing iov
Currently pointer iov is being dereferenced before the null check of iov
which can lead to null pointer dereference errors. Fix this by moving the
iov null check before the dereferencing.
Detected using cppcheck static analysis:
linux/arch/powerpc/platforms/powernv/pci-sriov.c:597:12: warning: Either
the condition '!iov' is redundant or there is possible null pointer
dereference: iov. [nullPointerRedundantCheck]
num_vfs = iov->num_vfs;
^ |
| In the Linux kernel, the following vulnerability has been resolved:
refscale: Fix uninitalized use of wait_queue_head_t
Running the refscale test occasionally crashes the kernel with the
following error:
[ 8569.952896] BUG: unable to handle page fault for address: ffffffffffffffe8
[ 8569.952900] #PF: supervisor read access in kernel mode
[ 8569.952902] #PF: error_code(0x0000) - not-present page
[ 8569.952904] PGD c4b048067 P4D c4b049067 PUD c4b04b067 PMD 0
[ 8569.952910] Oops: 0000 [#1] PREEMPT_RT SMP NOPTI
[ 8569.952916] Hardware name: Dell Inc. PowerEdge R750/0WMWCR, BIOS 1.2.4 05/28/2021
[ 8569.952917] RIP: 0010:prepare_to_wait_event+0x101/0x190
:
[ 8569.952940] Call Trace:
[ 8569.952941] <TASK>
[ 8569.952944] ref_scale_reader+0x380/0x4a0 [refscale]
[ 8569.952959] kthread+0x10e/0x130
[ 8569.952966] ret_from_fork+0x1f/0x30
[ 8569.952973] </TASK>
The likely cause is that init_waitqueue_head() is called after the call to
the torture_create_kthread() function that creates the ref_scale_reader
kthread. Although this init_waitqueue_head() call will very likely
complete before this kthread is created and starts running, it is
possible that the calling kthread will be delayed between the calls to
torture_create_kthread() and init_waitqueue_head(). In this case, the
new kthread will use the waitqueue head before it is properly initialized,
which is not good for the kernel's health and well-being.
The above crash happened here:
static inline void __add_wait_queue(...)
{
:
if (!(wq->flags & WQ_FLAG_PRIORITY)) <=== Crash here
The offset of flags from list_head entry in wait_queue_entry is
-0x18. If reader_tasks[i].wq.head.next is NULL as allocated reader_task
structure is zero initialized, the instruction will try to access address
0xffffffffffffffe8, which is exactly the fault address listed above.
This commit therefore invokes init_waitqueue_head() before creating
the kthread. |
| In the Linux kernel, the following vulnerability has been resolved:
cxl/pmem: Fix nvdimm registration races
A loop of the form:
while true; do modprobe cxl_pci; modprobe -r cxl_pci; done
...fails with the following crash signature:
BUG: kernel NULL pointer dereference, address: 0000000000000040
[..]
RIP: 0010:cxl_internal_send_cmd+0x5/0xb0 [cxl_core]
[..]
Call Trace:
<TASK>
cxl_pmem_ctl+0x121/0x240 [cxl_pmem]
nvdimm_get_config_data+0xd6/0x1a0 [libnvdimm]
nd_label_data_init+0x135/0x7e0 [libnvdimm]
nvdimm_probe+0xd6/0x1c0 [libnvdimm]
nvdimm_bus_probe+0x7a/0x1e0 [libnvdimm]
really_probe+0xde/0x380
__driver_probe_device+0x78/0x170
driver_probe_device+0x1f/0x90
__device_attach_driver+0x85/0x110
bus_for_each_drv+0x7d/0xc0
__device_attach+0xb4/0x1e0
bus_probe_device+0x9f/0xc0
device_add+0x445/0x9c0
nd_async_device_register+0xe/0x40 [libnvdimm]
async_run_entry_fn+0x30/0x130
...namely that the bottom half of async nvdimm device registration runs
after the CXL has already torn down the context that cxl_pmem_ctl()
needs. Unlike the ACPI NFIT case that benefits from launching multiple
nvdimm device registrations in parallel from those listed in the table,
CXL is already marked PROBE_PREFER_ASYNCHRONOUS. So provide for a
synchronous registration path to preclude this scenario. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ar5523: Fix use-after-free on ar5523_cmd() timed out
syzkaller reported use-after-free with the stack trace like below [1]:
[ 38.960489][ C3] ==================================================================
[ 38.963216][ C3] BUG: KASAN: use-after-free in ar5523_cmd_tx_cb+0x220/0x240
[ 38.964950][ C3] Read of size 8 at addr ffff888048e03450 by task swapper/3/0
[ 38.966363][ C3]
[ 38.967053][ C3] CPU: 3 PID: 0 Comm: swapper/3 Not tainted 6.0.0-09039-ga6afa4199d3d-dirty #18
[ 38.968464][ C3] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.0-1.fc36 04/01/2014
[ 38.969959][ C3] Call Trace:
[ 38.970841][ C3] <IRQ>
[ 38.971663][ C3] dump_stack_lvl+0xfc/0x174
[ 38.972620][ C3] print_report.cold+0x2c3/0x752
[ 38.973626][ C3] ? ar5523_cmd_tx_cb+0x220/0x240
[ 38.974644][ C3] kasan_report+0xb1/0x1d0
[ 38.975720][ C3] ? ar5523_cmd_tx_cb+0x220/0x240
[ 38.976831][ C3] ar5523_cmd_tx_cb+0x220/0x240
[ 38.978412][ C3] __usb_hcd_giveback_urb+0x353/0x5b0
[ 38.979755][ C3] usb_hcd_giveback_urb+0x385/0x430
[ 38.981266][ C3] dummy_timer+0x140c/0x34e0
[ 38.982925][ C3] ? notifier_call_chain+0xb5/0x1e0
[ 38.984761][ C3] ? rcu_read_lock_sched_held+0xb/0x60
[ 38.986242][ C3] ? lock_release+0x51c/0x790
[ 38.987323][ C3] ? _raw_read_unlock_irqrestore+0x37/0x70
[ 38.988483][ C3] ? __wake_up_common_lock+0xde/0x130
[ 38.989621][ C3] ? reacquire_held_locks+0x4a0/0x4a0
[ 38.990777][ C3] ? lock_acquire+0x472/0x550
[ 38.991919][ C3] ? rcu_read_lock_sched_held+0xb/0x60
[ 38.993138][ C3] ? lock_acquire+0x472/0x550
[ 38.994890][ C3] ? dummy_urb_enqueue+0x860/0x860
[ 38.996266][ C3] ? do_raw_spin_unlock+0x16f/0x230
[ 38.997670][ C3] ? dummy_urb_enqueue+0x860/0x860
[ 38.999116][ C3] call_timer_fn+0x1a0/0x6a0
[ 39.000668][ C3] ? add_timer_on+0x4a0/0x4a0
[ 39.002137][ C3] ? reacquire_held_locks+0x4a0/0x4a0
[ 39.003809][ C3] ? __next_timer_interrupt+0x226/0x2a0
[ 39.005509][ C3] __run_timers.part.0+0x69a/0xac0
[ 39.007025][ C3] ? dummy_urb_enqueue+0x860/0x860
[ 39.008716][ C3] ? call_timer_fn+0x6a0/0x6a0
[ 39.010254][ C3] ? cpuacct_percpu_seq_show+0x10/0x10
[ 39.011795][ C3] ? kvm_sched_clock_read+0x14/0x40
[ 39.013277][ C3] ? sched_clock_cpu+0x69/0x2b0
[ 39.014724][ C3] run_timer_softirq+0xb6/0x1d0
[ 39.016196][ C3] __do_softirq+0x1d2/0x9be
[ 39.017616][ C3] __irq_exit_rcu+0xeb/0x190
[ 39.019004][ C3] irq_exit_rcu+0x5/0x20
[ 39.020361][ C3] sysvec_apic_timer_interrupt+0x8f/0xb0
[ 39.021965][ C3] </IRQ>
[ 39.023237][ C3] <TASK>
In ar5523_probe(), ar5523_host_available() calls ar5523_cmd() as below
(there are other functions which finally call ar5523_cmd()):
ar5523_probe()
-> ar5523_host_available()
-> ar5523_cmd_read()
-> ar5523_cmd()
If ar5523_cmd() timed out, then ar5523_host_available() failed and
ar5523_probe() freed the device structure. So, ar5523_cmd_tx_cb()
might touch the freed structure.
This patch fixes this issue by canceling in-flight tx cmd if submitted
urb timed out. |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/kprobes: Fix null pointer reference in arch_prepare_kprobe()
I found a null pointer reference in arch_prepare_kprobe():
# echo 'p cmdline_proc_show' > kprobe_events
# echo 'p cmdline_proc_show+16' >> kprobe_events
Kernel attempted to read user page (0) - exploit attempt? (uid: 0)
BUG: Kernel NULL pointer dereference on read at 0x00000000
Faulting instruction address: 0xc000000000050bfc
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA PowerNV
Modules linked in:
CPU: 0 PID: 122 Comm: sh Not tainted 6.0.0-rc3-00007-gdcf8e5633e2e #10
NIP: c000000000050bfc LR: c000000000050bec CTR: 0000000000005bdc
REGS: c0000000348475b0 TRAP: 0300 Not tainted (6.0.0-rc3-00007-gdcf8e5633e2e)
MSR: 9000000000009033 <SF,HV,EE,ME,IR,DR,RI,LE> CR: 88002444 XER: 20040006
CFAR: c00000000022d100 DAR: 0000000000000000 DSISR: 40000000 IRQMASK: 0
...
NIP arch_prepare_kprobe+0x10c/0x2d0
LR arch_prepare_kprobe+0xfc/0x2d0
Call Trace:
0xc0000000012f77a0 (unreliable)
register_kprobe+0x3c0/0x7a0
__register_trace_kprobe+0x140/0x1a0
__trace_kprobe_create+0x794/0x1040
trace_probe_create+0xc4/0xe0
create_or_delete_trace_kprobe+0x2c/0x80
trace_parse_run_command+0xf0/0x210
probes_write+0x20/0x40
vfs_write+0xfc/0x450
ksys_write+0x84/0x140
system_call_exception+0x17c/0x3a0
system_call_vectored_common+0xe8/0x278
--- interrupt: 3000 at 0x7fffa5682de0
NIP: 00007fffa5682de0 LR: 0000000000000000 CTR: 0000000000000000
REGS: c000000034847e80 TRAP: 3000 Not tainted (6.0.0-rc3-00007-gdcf8e5633e2e)
MSR: 900000000280f033 <SF,HV,VEC,VSX,EE,PR,FP,ME,IR,DR,RI,LE> CR: 44002408 XER: 00000000
The address being probed has some special:
cmdline_proc_show: Probe based on ftrace
cmdline_proc_show+16: Probe for the next instruction at the ftrace location
The ftrace-based kprobe does not generate kprobe::ainsn::insn, it gets
set to NULL. In arch_prepare_kprobe() it will check for:
...
prev = get_kprobe(p->addr - 1);
preempt_enable_no_resched();
if (prev && ppc_inst_prefixed(ppc_inst_read(prev->ainsn.insn))) {
...
If prev is based on ftrace, 'ppc_inst_read(prev->ainsn.insn)' will occur
with a null pointer reference. At this point prev->addr will not be a
prefixed instruction, so the check can be skipped.
Check if prev is ftrace-based kprobe before reading 'prev->ainsn.insn'
to fix this problem.
[mpe: Trim oops] |
| In the Linux kernel, the following vulnerability has been resolved:
media: b2c2: Fix use-after-free causing by irq_check_work in flexcop_pci_remove
The original code uses cancel_delayed_work() in flexcop_pci_remove(), which
does not guarantee that the delayed work item irq_check_work has fully
completed if it was already running. This leads to use-after-free scenarios
where flexcop_pci_remove() may free the flexcop_device while irq_check_work
is still active and attempts to dereference the device.
A typical race condition is illustrated below:
CPU 0 (remove) | CPU 1 (delayed work callback)
flexcop_pci_remove() | flexcop_pci_irq_check_work()
cancel_delayed_work() |
flexcop_device_kfree(fc_pci->fc_dev) |
| fc = fc_pci->fc_dev; // UAF
This is confirmed by a KASAN report:
==================================================================
BUG: KASAN: slab-use-after-free in __run_timer_base.part.0+0x7d7/0x8c0
Write of size 8 at addr ffff8880093aa8c8 by task bash/135
...
Call Trace:
<IRQ>
dump_stack_lvl+0x55/0x70
print_report+0xcf/0x610
? __run_timer_base.part.0+0x7d7/0x8c0
kasan_report+0xb8/0xf0
? __run_timer_base.part.0+0x7d7/0x8c0
__run_timer_base.part.0+0x7d7/0x8c0
? __pfx___run_timer_base.part.0+0x10/0x10
? __pfx_read_tsc+0x10/0x10
? ktime_get+0x60/0x140
? lapic_next_event+0x11/0x20
? clockevents_program_event+0x1d4/0x2a0
run_timer_softirq+0xd1/0x190
handle_softirqs+0x16a/0x550
irq_exit_rcu+0xaf/0xe0
sysvec_apic_timer_interrupt+0x70/0x80
</IRQ>
...
Allocated by task 1:
kasan_save_stack+0x24/0x50
kasan_save_track+0x14/0x30
__kasan_kmalloc+0x7f/0x90
__kmalloc_noprof+0x1be/0x460
flexcop_device_kmalloc+0x54/0xe0
flexcop_pci_probe+0x1f/0x9d0
local_pci_probe+0xdc/0x190
pci_device_probe+0x2fe/0x470
really_probe+0x1ca/0x5c0
__driver_probe_device+0x248/0x310
driver_probe_device+0x44/0x120
__driver_attach+0xd2/0x310
bus_for_each_dev+0xed/0x170
bus_add_driver+0x208/0x500
driver_register+0x132/0x460
do_one_initcall+0x89/0x300
kernel_init_freeable+0x40d/0x720
kernel_init+0x1a/0x150
ret_from_fork+0x10c/0x1a0
ret_from_fork_asm+0x1a/0x30
Freed by task 135:
kasan_save_stack+0x24/0x50
kasan_save_track+0x14/0x30
kasan_save_free_info+0x3a/0x60
__kasan_slab_free+0x3f/0x50
kfree+0x137/0x370
flexcop_device_kfree+0x32/0x50
pci_device_remove+0xa6/0x1d0
device_release_driver_internal+0xf8/0x210
pci_stop_bus_device+0x105/0x150
pci_stop_and_remove_bus_device_locked+0x15/0x30
remove_store+0xcc/0xe0
kernfs_fop_write_iter+0x2c3/0x440
vfs_write+0x871/0xd70
ksys_write+0xee/0x1c0
do_syscall_64+0xac/0x280
entry_SYSCALL_64_after_hwframe+0x77/0x7f
...
Replace cancel_delayed_work() with cancel_delayed_work_sync() to ensure
that the delayed work item is properly canceled and any executing delayed
work has finished before the device memory is deallocated.
This bug was initially identified through static analysis. To reproduce
and test it, I simulated the B2C2 FlexCop PCI device in QEMU and introduced
artificial delays within the flexcop_pci_irq_check_work() function to
increase the likelihood of triggering the bug. |
| In the Linux kernel, the following vulnerability has been resolved:
devlink: report devlink_port_type_warn source device
devlink_port_type_warn is scheduled for port devlink and warning
when the port type is not set. But from this warning it is not easy
found out which device (driver) has no devlink port set.
[ 3709.975552] Type was not set for devlink port.
[ 3709.975579] WARNING: CPU: 1 PID: 13092 at net/devlink/leftover.c:6775 devlink_port_type_warn+0x11/0x20
[ 3709.993967] Modules linked in: openvswitch nf_conncount nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nfnetlink bluetooth rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver nfs lockd grace fscache netfs vhost_net vhost vhost_iotlb tap tun bridge stp llc qrtr intel_rapl_msr intel_rapl_common i10nm_edac nfit libnvdimm x86_pkg_temp_thermal mlx5_ib intel_powerclamp coretemp dell_wmi ledtrig_audio sparse_keymap ipmi_ssif kvm_intel ib_uverbs rfkill ib_core video kvm iTCO_wdt acpi_ipmi intel_vsec irqbypass ipmi_si iTCO_vendor_support dcdbas ipmi_devintf mei_me ipmi_msghandler rapl mei intel_cstate isst_if_mmio isst_if_mbox_pci dell_smbios intel_uncore isst_if_common i2c_i801 dell_wmi_descriptor wmi_bmof i2c_smbus intel_pch_thermal pcspkr acpi_power_meter xfs libcrc32c sd_mod sg nvme_tcp mgag200 i2c_algo_bit nvme_fabrics drm_shmem_helper drm_kms_helper nvme syscopyarea ahci sysfillrect sysimgblt nvme_core fb_sys_fops crct10dif_pclmul libahci mlx5_core sfc crc32_pclmul nvme_common drm
[ 3709.994030] crc32c_intel mtd t10_pi mlxfw libata tg3 mdio megaraid_sas psample ghash_clmulni_intel pci_hyperv_intf wmi dm_multipath sunrpc dm_mirror dm_region_hash dm_log dm_mod be2iscsi bnx2i cnic uio cxgb4i cxgb4 tls libcxgbi libcxgb qla4xxx iscsi_boot_sysfs iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi fuse
[ 3710.108431] CPU: 1 PID: 13092 Comm: kworker/1:1 Kdump: loaded Not tainted 5.14.0-319.el9.x86_64 #1
[ 3710.108435] Hardware name: Dell Inc. PowerEdge R750/0PJ80M, BIOS 1.8.2 09/14/2022
[ 3710.108437] Workqueue: events devlink_port_type_warn
[ 3710.108440] RIP: 0010:devlink_port_type_warn+0x11/0x20
[ 3710.108443] Code: 84 76 fe ff ff 48 c7 03 20 0e 1a ad 31 c0 e9 96 fd ff ff 66 0f 1f 44 00 00 0f 1f 44 00 00 48 c7 c7 18 24 4e ad e8 ef 71 62 ff <0f> 0b c3 cc cc cc cc 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 f6 87
[ 3710.108445] RSP: 0018:ff3b6d2e8b3c7e90 EFLAGS: 00010282
[ 3710.108447] RAX: 0000000000000000 RBX: ff366d6580127080 RCX: 0000000000000027
[ 3710.108448] RDX: 0000000000000027 RSI: 00000000ffff86de RDI: ff366d753f41f8c8
[ 3710.108449] RBP: ff366d658ff5a0c0 R08: ff366d753f41f8c0 R09: ff3b6d2e8b3c7e18
[ 3710.108450] R10: 0000000000000001 R11: 0000000000000023 R12: ff366d753f430600
[ 3710.108451] R13: ff366d753f436900 R14: 0000000000000000 R15: ff366d753f436905
[ 3710.108452] FS: 0000000000000000(0000) GS:ff366d753f400000(0000) knlGS:0000000000000000
[ 3710.108453] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 3710.108454] CR2: 00007f1c57bc74e0 CR3: 000000111d26a001 CR4: 0000000000773ee0
[ 3710.108456] PKRU: 55555554
[ 3710.108457] Call Trace:
[ 3710.108458] <TASK>
[ 3710.108459] process_one_work+0x1e2/0x3b0
[ 3710.108466] ? rescuer_thread+0x390/0x390
[ 3710.108468] worker_thread+0x50/0x3a0
[ 3710.108471] ? rescuer_thread+0x390/0x390
[ 3710.108473] kthread+0xdd/0x100
[ 3710.108477] ? kthread_complete_and_exit+0x20/0x20
[ 3710.108479] ret_from_fork+0x1f/0x30
[ 3710.108485] </TASK>
[ 3710.108486] ---[ end trace 1b4b23cd0c65d6a0 ]---
After patch:
[ 402.473064] ice 0000:41:00.0: Type was not set for devlink port.
[ 402.473064] ice 0000:41:00.1: Type was not set for devlink port. |
| In the Linux kernel, the following vulnerability has been resolved:
net: hns3: using the num_tqps in the vf driver to apply for resources
Currently, hdev->htqp is allocated using hdev->num_tqps, and kinfo->tqp
is allocated using kinfo->num_tqps. However, kinfo->num_tqps is set to
min(new_tqps, hdev->num_tqps); Therefore, kinfo->num_tqps may be smaller
than hdev->num_tqps, which causes some hdev->htqp[i] to remain
uninitialized in hclgevf_knic_setup().
Thus, this patch allocates hdev->htqp and kinfo->tqp using hdev->num_tqps,
ensuring that the lengths of hdev->htqp and kinfo->tqp are consistent
and that all elements are properly initialized. |
| In the Linux kernel, the following vulnerability has been resolved:
mm: swap: check for stable address space before operating on the VMA
It is possible to hit a zero entry while traversing the vmas in unuse_mm()
called from swapoff path and accessing it causes the OOPS:
Unable to handle kernel NULL pointer dereference at virtual address
0000000000000446--> Loading the memory from offset 0x40 on the
XA_ZERO_ENTRY as address.
Mem abort info:
ESR = 0x0000000096000005
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x05: level 1 translation fault
The issue is manifested from the below race between the fork() on a
process and swapoff:
fork(dup_mmap()) swapoff(unuse_mm)
--------------- -----------------
1) Identical mtree is built using
__mt_dup().
2) copy_pte_range()-->
copy_nonpresent_pte():
The dst mm is added into the
mmlist to be visible to the
swapoff operation.
3) Fatal signal is sent to the parent
process(which is the current during the
fork) thus skip the duplication of the
vmas and mark the vma range with
XA_ZERO_ENTRY as a marker for this process
that helps during exit_mmap().
4) swapoff is tried on the
'mm' added to the 'mmlist' as
part of the 2.
5) unuse_mm(), that iterates
through the vma's of this 'mm'
will hit the non-NULL zero entry
and operating on this zero entry
as a vma is resulting into the
oops.
The proper fix would be around not exposing this partially-valid tree to
others when droping the mmap lock, which is being solved with [1]. A
simpler solution would be checking for MMF_UNSTABLE, as it is set if
mm_struct is not fully initialized in dup_mmap().
Thanks to Liam/Lorenzo/David for all the suggestions in fixing this
issue. |
| In the Linux kernel, the following vulnerability has been resolved:
blk-mq: fix blk_mq_tags double free while nr_requests grown
In the case user trigger tags grow by queue sysfs attribute nr_requests,
hctx->sched_tags will be freed directly and replaced with a new
allocated tags, see blk_mq_tag_update_depth().
The problem is that hctx->sched_tags is from elevator->et->tags, while
et->tags is still the freed tags, hence later elevator exit will try to
free the tags again, causing kernel panic.
Fix this problem by replacing et->tags with new allocated tags as well.
Noted there are still some long term problems that will require some
refactor to be fixed thoroughly[1].
[1] https://lore.kernel.org/all/[email protected]/ |
| In the Linux kernel, the following vulnerability has been resolved:
thunderbolt: Fix use-after-free in tb_dp_dprx_work
The original code relies on cancel_delayed_work() in tb_dp_dprx_stop(),
which does not ensure that the delayed work item tunnel->dprx_work has
fully completed if it was already running. This leads to use-after-free
scenarios where tb_tunnel is deallocated by tb_tunnel_put(), while
tunnel->dprx_work remains active and attempts to dereference tb_tunnel
in tb_dp_dprx_work().
A typical race condition is illustrated below:
CPU 0 | CPU 1
tb_dp_tunnel_active() |
tb_deactivate_and_free_tunnel()| tb_dp_dprx_start()
tb_tunnel_deactivate() | queue_delayed_work()
tb_dp_activate() |
tb_dp_dprx_stop() | tb_dp_dprx_work() //delayed worker
cancel_delayed_work() |
tb_tunnel_put(tunnel); |
| tunnel = container_of(...); //UAF
| tunnel-> //UAF
Replacing cancel_delayed_work() with cancel_delayed_work_sync() is
not feasible as it would introduce a deadlock: both tb_dp_dprx_work()
and the cleanup path acquire tb->lock, and cancel_delayed_work_sync()
would wait indefinitely for the work item that cannot proceed.
Instead, implement proper reference counting:
- If cancel_delayed_work() returns true (work is pending), we release
the reference in the stop function.
- If it returns false (work is executing or already completed), the
reference is released in delayed work function itself.
This ensures the tb_tunnel remains valid during work item execution
while preventing memory leaks.
This bug was found by static analysis. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: essiv - Check ssize for decryption and in-place encryption
Move the ssize check to the start in essiv_aead_crypt so that
it's also checked for decryption and in-place encryption. |
| In the Linux kernel, the following vulnerability has been resolved:
pinctrl: check the return value of pinmux_ops::get_function_name()
While the API contract in docs doesn't specify it explicitly, the
generic implementation of the get_function_name() callback from struct
pinmux_ops - pinmux_generic_get_function_name() - can fail and return
NULL. This is already checked in pinmux_check_ops() so add a similar
check in pinmux_func_name_to_selector() instead of passing the returned
pointer right down to strcmp() where the NULL can get dereferenced. This
is normal operation when adding new pinfunctions. |
| In the Linux kernel, the following vulnerability has been resolved:
misc: fastrpc: fix possible map leak in fastrpc_put_args
copy_to_user() failure would cause an early return without cleaning up
the fdlist, which has been updated by the DSP. This could lead to map
leak. Fix this by redirecting to a cleanup path on failure, ensuring
that all mapped buffers are properly released before returning. |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: endpoint: pci-epf-test: Add NULL check for DMA channels before release
The fields dma_chan_tx and dma_chan_rx of the struct pci_epf_test can be
NULL even after EPF initialization. Then it is prudent to check that
they have non-NULL values before releasing the channels. Add the checks
in pci_epf_test_clean_dma_chan().
Without the checks, NULL pointer dereferences happen and they can lead
to a kernel panic in some cases:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000050
Call trace:
dma_release_channel+0x2c/0x120 (P)
pci_epf_test_epc_deinit+0x94/0xc0 [pci_epf_test]
pci_epc_deinit_notify+0x74/0xc0
tegra_pcie_ep_pex_rst_irq+0x250/0x5d8
irq_thread_fn+0x34/0xb8
irq_thread+0x18c/0x2e8
kthread+0x14c/0x210
ret_from_fork+0x10/0x20
[mani: trimmed the stack trace] |
