| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
idpf: fix checksums set in idpf_rx_rsc()
idpf_rx_rsc() uses skb_transport_offset(skb) while the transport header
is not set yet.
This triggers the following warning for CONFIG_DEBUG_NET=y builds.
DEBUG_NET_WARN_ON_ONCE(!skb_transport_header_was_set(skb))
[ 69.261620] WARNING: CPU: 7 PID: 0 at ./include/linux/skbuff.h:3020 idpf_vport_splitq_napi_poll (include/linux/skbuff.h:3020) idpf
[ 69.261629] Modules linked in: vfat fat dummy bridge intel_uncore_frequency_tpmi intel_uncore_frequency_common intel_vsec_tpmi idpf intel_vsec cdc_ncm cdc_eem cdc_ether usbnet mii xhci_pci xhci_hcd ehci_pci ehci_hcd libeth
[ 69.261644] CPU: 7 UID: 0 PID: 0 Comm: swapper/7 Tainted: G S W 6.14.0-smp-DEV #1697
[ 69.261648] Tainted: [S]=CPU_OUT_OF_SPEC, [W]=WARN
[ 69.261650] RIP: 0010:idpf_vport_splitq_napi_poll (include/linux/skbuff.h:3020) idpf
[ 69.261677] ? __warn (kernel/panic.c:242 kernel/panic.c:748)
[ 69.261682] ? idpf_vport_splitq_napi_poll (include/linux/skbuff.h:3020) idpf
[ 69.261687] ? report_bug (lib/bug.c:?)
[ 69.261690] ? handle_bug (arch/x86/kernel/traps.c:285)
[ 69.261694] ? exc_invalid_op (arch/x86/kernel/traps.c:309)
[ 69.261697] ? asm_exc_invalid_op (arch/x86/include/asm/idtentry.h:621)
[ 69.261700] ? __pfx_idpf_vport_splitq_napi_poll (drivers/net/ethernet/intel/idpf/idpf_txrx.c:4011) idpf
[ 69.261704] ? idpf_vport_splitq_napi_poll (include/linux/skbuff.h:3020) idpf
[ 69.261708] ? idpf_vport_splitq_napi_poll (drivers/net/ethernet/intel/idpf/idpf_txrx.c:3072) idpf
[ 69.261712] __napi_poll (net/core/dev.c:7194)
[ 69.261716] net_rx_action (net/core/dev.c:7265)
[ 69.261718] ? __qdisc_run (net/sched/sch_generic.c:293)
[ 69.261721] ? sched_clock (arch/x86/include/asm/preempt.h:84 arch/x86/kernel/tsc.c:288)
[ 69.261726] handle_softirqs (kernel/softirq.c:561) |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix softlockup in arena_map_free on 64k page kernel
On an aarch64 kernel with CONFIG_PAGE_SIZE_64KB=y,
arena_htab tests cause a segmentation fault and soft lockup.
The same failure is not observed with 4k pages on aarch64.
It turns out arena_map_free() is calling
apply_to_existing_page_range() with the address returned by
bpf_arena_get_kern_vm_start(). If this address is not page-aligned
the code ends up calling apply_to_pte_range() with that unaligned
address causing soft lockup.
Fix it by round up GUARD_SZ to PAGE_SIZE << 1 so that the
division by 2 in bpf_arena_get_kern_vm_start() returns
a page-aligned value. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: x86: Load DR6 with guest value only before entering .vcpu_run() loop
Move the conditional loading of hardware DR6 with the guest's DR6 value
out of the core .vcpu_run() loop to fix a bug where KVM can load hardware
with a stale vcpu->arch.dr6.
When the guest accesses a DR and host userspace isn't debugging the guest,
KVM disables DR interception and loads the guest's values into hardware on
VM-Enter and saves them on VM-Exit. This allows the guest to access DRs
at will, e.g. so that a sequence of DR accesses to configure a breakpoint
only generates one VM-Exit.
For DR0-DR3, the logic/behavior is identical between VMX and SVM, and also
identical between KVM_DEBUGREG_BP_ENABLED (userspace debugging the guest)
and KVM_DEBUGREG_WONT_EXIT (guest using DRs), and so KVM handles loading
DR0-DR3 in common code, _outside_ of the core kvm_x86_ops.vcpu_run() loop.
But for DR6, the guest's value doesn't need to be loaded into hardware for
KVM_DEBUGREG_BP_ENABLED, and SVM provides a dedicated VMCB field whereas
VMX requires software to manually load the guest value, and so loading the
guest's value into DR6 is handled by {svm,vmx}_vcpu_run(), i.e. is done
_inside_ the core run loop.
Unfortunately, saving the guest values on VM-Exit is initiated by common
x86, again outside of the core run loop. If the guest modifies DR6 (in
hardware, when DR interception is disabled), and then the next VM-Exit is
a fastpath VM-Exit, KVM will reload hardware DR6 with vcpu->arch.dr6 and
clobber the guest's actual value.
The bug shows up primarily with nested VMX because KVM handles the VMX
preemption timer in the fastpath, and the window between hardware DR6
being modified (in guest context) and DR6 being read by guest software is
orders of magnitude larger in a nested setup. E.g. in non-nested, the
VMX preemption timer would need to fire precisely between #DB injection
and the #DB handler's read of DR6, whereas with a KVM-on-KVM setup, the
window where hardware DR6 is "dirty" extends all the way from L1 writing
DR6 to VMRESUME (in L1).
L1's view:
==========
<L1 disables DR interception>
CPU 0/KVM-7289 [023] d.... 2925.640961: kvm_entry: vcpu 0
A: L1 Writes DR6
CPU 0/KVM-7289 [023] d.... 2925.640963: <hack>: Set DRs, DR6 = 0xffff0ff1
B: CPU 0/KVM-7289 [023] d.... 2925.640967: kvm_exit: vcpu 0 reason EXTERNAL_INTERRUPT intr_info 0x800000ec
D: L1 reads DR6, arch.dr6 = 0
CPU 0/KVM-7289 [023] d.... 2925.640969: <hack>: Sync DRs, DR6 = 0xffff0ff0
CPU 0/KVM-7289 [023] d.... 2925.640976: kvm_entry: vcpu 0
L2 reads DR6, L1 disables DR interception
CPU 0/KVM-7289 [023] d.... 2925.640980: kvm_exit: vcpu 0 reason DR_ACCESS info1 0x0000000000000216
CPU 0/KVM-7289 [023] d.... 2925.640983: kvm_entry: vcpu 0
CPU 0/KVM-7289 [023] d.... 2925.640983: <hack>: Set DRs, DR6 = 0xffff0ff0
L2 detects failure
CPU 0/KVM-7289 [023] d.... 2925.640987: kvm_exit: vcpu 0 reason HLT
L1 reads DR6 (confirms failure)
CPU 0/KVM-7289 [023] d.... 2925.640990: <hack>: Sync DRs, DR6 = 0xffff0ff0
L0's view:
==========
L2 reads DR6, arch.dr6 = 0
CPU 23/KVM-5046 [001] d.... 3410.005610: kvm_exit: vcpu 23 reason DR_ACCESS info1 0x0000000000000216
CPU 23/KVM-5046 [001] ..... 3410.005610: kvm_nested_vmexit: vcpu 23 reason DR_ACCESS info1 0x0000000000000216
L2 => L1 nested VM-Exit
CPU 23/KVM-5046 [001] ..... 3410.005610: kvm_nested_vmexit_inject: reason: DR_ACCESS ext_inf1: 0x0000000000000216
CPU 23/KVM-5046 [001] d.... 3410.005610: kvm_entry: vcpu 23
CPU 23/KVM-5046 [001] d.... 3410.005611: kvm_exit: vcpu 23 reason VMREAD
CPU 23/KVM-5046 [001] d.... 3410.005611: kvm_entry: vcpu 23
CPU 23/KVM-5046 [001] d.... 3410.
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btusb: mediatek: Add locks for usb_driver_claim_interface()
The documentation for usb_driver_claim_interface() says that "the
device lock" is needed when the function is called from places other
than probe(). This appears to be the lock for the USB interface
device. The Mediatek btusb code gets called via this path:
Workqueue: hci0 hci_power_on [bluetooth]
Call trace:
usb_driver_claim_interface
btusb_mtk_claim_iso_intf
btusb_mtk_setup
hci_dev_open_sync
hci_power_on
process_scheduled_works
worker_thread
kthread
With the above call trace the device lock hasn't been claimed. Claim
it.
Without this fix, we'd sometimes see the error "Failed to claim iso
interface". Sometimes we'd even see worse errors, like a NULL pointer
dereference (where `intf->dev.driver` was NULL) with a trace like:
Call trace:
usb_suspend_both
usb_runtime_suspend
__rpm_callback
rpm_suspend
pm_runtime_work
process_scheduled_works
Both errors appear to be fixed with the proper locking. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_tables: reject mismatching sum of field_len with set key length
The field length description provides the length of each separated key
field in the concatenation, each field gets rounded up to 32-bits to
calculate the pipapo rule width from pipapo_init(). The set key length
provides the total size of the key aligned to 32-bits.
Register-based arithmetics still allows for combining mismatching set
key length and field length description, eg. set key length 10 and field
description [ 5, 4 ] leading to pipapo width of 12. |
| In the Linux kernel, the following vulnerability has been resolved:
rxrpc, afs: Fix peer hash locking vs RCU callback
In its address list, afs now retains pointers to and refs on one or more
rxrpc_peer objects. The address list is freed under RCU and at this time,
it puts the refs on those peers.
Now, when an rxrpc_peer object runs out of refs, it gets removed from the
peer hash table and, for that, rxrpc has to take a spinlock. However, it
is now being called from afs's RCU cleanup, which takes place in BH
context - but it is just taking an ordinary spinlock.
The put may also be called from non-BH context, and so there exists the
possibility of deadlock if the BH-based RCU cleanup happens whilst the hash
spinlock is held. This led to the attached lockdep complaint.
Fix this by changing spinlocks of rxnet->peer_hash_lock back to
BH-disabling locks.
================================
WARNING: inconsistent lock state
6.13.0-rc5-build2+ #1223 Tainted: G E
--------------------------------
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
swapper/1/0 [HC0[0]:SC1[1]:HE1:SE0] takes:
ffff88810babe228 (&rxnet->peer_hash_lock){+.?.}-{3:3}, at: rxrpc_put_peer+0xcb/0x180
{SOFTIRQ-ON-W} state was registered at:
mark_usage+0x164/0x180
__lock_acquire+0x544/0x990
lock_acquire.part.0+0x103/0x280
_raw_spin_lock+0x2f/0x40
rxrpc_peer_keepalive_worker+0x144/0x440
process_one_work+0x486/0x7c0
process_scheduled_works+0x73/0x90
worker_thread+0x1c8/0x2a0
kthread+0x19b/0x1b0
ret_from_fork+0x24/0x40
ret_from_fork_asm+0x1a/0x30
irq event stamp: 972402
hardirqs last enabled at (972402): [<ffffffff8244360e>] _raw_spin_unlock_irqrestore+0x2e/0x50
hardirqs last disabled at (972401): [<ffffffff82443328>] _raw_spin_lock_irqsave+0x18/0x60
softirqs last enabled at (972300): [<ffffffff810ffbbe>] handle_softirqs+0x3ee/0x430
softirqs last disabled at (972313): [<ffffffff810ffc54>] __irq_exit_rcu+0x44/0x110
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&rxnet->peer_hash_lock);
<Interrupt>
lock(&rxnet->peer_hash_lock);
*** DEADLOCK ***
1 lock held by swapper/1/0:
#0: ffffffff83576be0 (rcu_callback){....}-{0:0}, at: rcu_lock_acquire+0x7/0x30
stack backtrace:
CPU: 1 UID: 0 PID: 0 Comm: swapper/1 Tainted: G E 6.13.0-rc5-build2+ #1223
Tainted: [E]=UNSIGNED_MODULE
Hardware name: ASUS All Series/H97-PLUS, BIOS 2306 10/09/2014
Call Trace:
<IRQ>
dump_stack_lvl+0x57/0x80
print_usage_bug.part.0+0x227/0x240
valid_state+0x53/0x70
mark_lock_irq+0xa5/0x2f0
mark_lock+0xf7/0x170
mark_usage+0xe1/0x180
__lock_acquire+0x544/0x990
lock_acquire.part.0+0x103/0x280
_raw_spin_lock+0x2f/0x40
rxrpc_put_peer+0xcb/0x180
afs_free_addrlist+0x46/0x90 [kafs]
rcu_do_batch+0x2d2/0x640
rcu_core+0x2f7/0x350
handle_softirqs+0x1ee/0x430
__irq_exit_rcu+0x44/0x110
irq_exit_rcu+0xa/0x30
sysvec_apic_timer_interrupt+0x7f/0xa0
</IRQ> |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: correct handling of extreme memory squeeze
Testing with iperf3 using the "pasta" protocol splicer has revealed
a problem in the way tcp handles window advertising in extreme memory
squeeze situations.
Under memory pressure, a socket endpoint may temporarily advertise
a zero-sized window, but this is not stored as part of the socket data.
The reasoning behind this is that it is considered a temporary setting
which shouldn't influence any further calculations.
However, if we happen to stall at an unfortunate value of the current
window size, the algorithm selecting a new value will consistently fail
to advertise a non-zero window once we have freed up enough memory.
This means that this side's notion of the current window size is
different from the one last advertised to the peer, causing the latter
to not send any data to resolve the sitution.
The problem occurs on the iperf3 server side, and the socket in question
is a completely regular socket with the default settings for the
fedora40 kernel. We do not use SO_PEEK or SO_RCVBUF on the socket.
The following excerpt of a logging session, with own comments added,
shows more in detail what is happening:
// tcp_v4_rcv(->)
// tcp_rcv_established(->)
[5201<->39222]: ==== Activating log @ net/ipv4/tcp_input.c/tcp_data_queue()/5257 ====
[5201<->39222]: tcp_data_queue(->)
[5201<->39222]: DROPPING skb [265600160..265665640], reason: SKB_DROP_REASON_PROTO_MEM
[rcv_nxt 265600160, rcv_wnd 262144, snt_ack 265469200, win_now 131184]
[copied_seq 259909392->260034360 (124968), unread 5565800, qlen 85, ofoq 0]
[OFO queue: gap: 65480, len: 0]
[5201<->39222]: tcp_data_queue(<-)
[5201<->39222]: __tcp_transmit_skb(->)
[tp->rcv_wup: 265469200, tp->rcv_wnd: 262144, tp->rcv_nxt 265600160]
[5201<->39222]: tcp_select_window(->)
[5201<->39222]: (inet_csk(sk)->icsk_ack.pending & ICSK_ACK_NOMEM) ? --> TRUE
[tp->rcv_wup: 265469200, tp->rcv_wnd: 262144, tp->rcv_nxt 265600160]
returning 0
[5201<->39222]: tcp_select_window(<-)
[5201<->39222]: ADVERTISING WIN 0, ACK_SEQ: 265600160
[5201<->39222]: [__tcp_transmit_skb(<-)
[5201<->39222]: tcp_rcv_established(<-)
[5201<->39222]: tcp_v4_rcv(<-)
// Receive queue is at 85 buffers and we are out of memory.
// We drop the incoming buffer, although it is in sequence, and decide
// to send an advertisement with a window of zero.
// We don't update tp->rcv_wnd and tp->rcv_wup accordingly, which means
// we unconditionally shrink the window.
[5201<->39222]: tcp_recvmsg_locked(->)
[5201<->39222]: __tcp_cleanup_rbuf(->) tp->rcv_wup: 265469200, tp->rcv_wnd: 262144, tp->rcv_nxt 265600160
[5201<->39222]: [new_win = 0, win_now = 131184, 2 * win_now = 262368]
[5201<->39222]: [new_win >= (2 * win_now) ? --> time_to_ack = 0]
[5201<->39222]: NOT calling tcp_send_ack()
[tp->rcv_wup: 265469200, tp->rcv_wnd: 262144, tp->rcv_nxt 265600160]
[5201<->39222]: __tcp_cleanup_rbuf(<-)
[rcv_nxt 265600160, rcv_wnd 262144, snt_ack 265469200, win_now 131184]
[copied_seq 260040464->260040464 (0), unread 5559696, qlen 85, ofoq 0]
returning 6104 bytes
[5201<->39222]: tcp_recvmsg_locked(<-)
// After each read, the algorithm for calculating the new receive
// window in __tcp_cleanup_rbuf() finds it is too small to advertise
// or to update tp->rcv_wnd.
// Meanwhile, the peer thinks the window is zero, and will not send
// any more data to trigger an update from the interrupt mode side.
[5201<->39222]: tcp_recvmsg_locked(->)
[5201<->39222]: __tcp_cleanup_rbuf(->) tp->rcv_wup: 265469200, tp->rcv_wnd: 262144, tp->rcv_nxt 265600160
[5201<->39222]: [new_win = 262144, win_now = 131184, 2 * win_n
---truncated--- |
| Inappropriate implementation in SiteIsolation in Google Chrome prior to 151.0.7922.72 allowed a remote attacker who had compromised the renderer process to bypass site isolation via a crafted HTML page. (Chromium security severity: High) |
| Dify AI Workflow oauth_redirect_url Open Redirect Vulnerability. This vulnerability allows remote attackers to disclose sensitive information on affected installations of Dify. User interaction is required to exploit this vulnerability in that the target must visit a malicious page or open a malicious file.
The specific flaw exists within the OAuth flow handling in the AppInitializer component. An attacker can force a redirection to a site that serves malicious content. An attacker can leverage this vulnerability to disclose information in the context of the application. Was ZDI-CAN-29196. |
| Rclone is a command-line program to sync files and directories to and from different cloud storage providers. Prior to 1.74.4, rclone serve restic --private-repos enforces authorization using the routed user path segment while building the backend object key from the raw uncleaned URL path, allowing an authenticated user to include .. in a request such as //..//config and read, overwrite, or delete another user's private repository on backends that clean path components. This issue is fixed in version 1.74.4. |
| OpenRemote before 1.26.2 contains an authentication bypass vulnerability in the console registration API that allows unauthenticated attackers to update existing console assets by supplying a known asset identifier. Attackers can overwrite push notification tokens and console metadata without authentication or ownership validation, redirecting notifications or denying delivery to legitimate consoles. |
| Twig is a template language for PHP. From 3.9.0 until 3.26.0, template_from_string() compiles an inner template under a synthesized __string_template__<hash> name that can fall outside a SourcePolicyInterface sandbox decision, allowing a sandboxed template that can call template_from_string and include to render an inner template without security policy enforcement. This issue is fixed in version 3.26.0. |
| Easy!Appointments is a self hosted appointment scheduler. In versions up to and including 1.5.2, the booking reschedule view at `/index.php/booking/reschedule/{appointment_hash}` (handled by `Booking::index()`) embeds the entire customer record as inline JavaScript (`const vars = {... "customer_data": {...}, ...}`) without authentication and without field whitelisting. Anyone in possession of the 12-character `appointment_hash` — which appears in plain text in reschedule emails, confirmation page URLs, and operator-side calendar links — can read every column of that customer's row in the `ea_users` table. Version 1.6.0 contains a patch. |
| Easy!Appointments is a self hosted appointment scheduler. Versions prior to 1.6.0 correctly filter provider-scoped appointments in the `appointments/search` response, proving that provider isolation is an intended security boundary. However, the direct mutation endpoints `appointments/store` and `appointments/update` only check generic appointment privileges and never verify that the submitted `id_users_provider` belongs to the current session. A normal authenticated provider can inject new appointments into another provider's schedule via `store`, or reassign existing appointments into a foreign provider's calendar via `update`. The `store` path contains an additional write-before-crash bug: the unauthorized row is committed to the database before the controller crashes on a type error, so the attacker receives an error response while the foreign appointment is already persisted. Version 1.6.0 patches the issue. |
| A flaw was found in Foreman. This broken access control vulnerability allows an authenticated user with host-edit permissions to retarget an existing lookup value override to a different host. This is achieved by modifying the match field through nested host attributes, effectively bypassing authorisation checks. The consequence is the potential for unauthorised modification of managed host configurations across different organisational and location boundaries. |
| URL redirection to untrusted site ('open redirect') vulnerability in The Wikimedia Foundation Mediawiki - UrlShortener Extension allows Cross-Site Flashing.
This issue affects Mediawiki - UrlShortener Extension: from * before 1.43.9, 1.44.6, 1.45.4. |
| Tina is a headless content management system. In versions prior to @tinacms/app 2.5.6 and tinacms 3.9.3, cross-origin postMessage handlers and a rich-text URL-sanitization bypass enable stored XSS and session takeover. The library registers window message listeners — the useTina overlay handler, the OAuth authentication popup handler, and the admin↔preview iframe GraphQL reducer — that act on event.data without verifying event.origin or event.source and post messages using non-specific target origins, while insufficient URL sanitization in rich-text content allows malicious URLs to persist and execute. A page the victim visits (or a window in an opener/iframe relationship with a Tina admin) can forge messages to drive the editor, inject preview content, or observe/forge the OAuth popup channel to take over an authenticated editing session. This issue has been fixed in versions @tinacms/app 2.5.6 and tinacms 3.9.3. |
| The admin panel lacks standard security headers, enabling clickjacking and cross-site scripting attacks. |
| Improper Restriction of XML External Entity Reference vulnerability in Apache Lucene.Net (Lucene.Net.Analysis.Common library).
This issue affects Apache Lucene.Net.Analysis.Common: from 4.8.0-beta00005 before 4.8.0-beta00018.
Users are recommended to upgrade to version 4.8.0-beta00018, which fixes the issue. |
| An insecure direct object reference
vulnerability in Koollab LMS allowed an authenticated user to query the course completion progress
of any other user without authorisation, disclosing private learning progress
information. |
