| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
mm: avoid overflows in dirty throttling logic
The dirty throttling logic is interspersed with assumptions that dirty
limits in PAGE_SIZE units fit into 32-bit (so that various multiplications
fit into 64-bits). If limits end up being larger, we will hit overflows,
possible divisions by 0 etc. Fix these problems by never allowing so
large dirty limits as they have dubious practical value anyway. For
dirty_bytes / dirty_background_bytes interfaces we can just refuse to set
so large limits. For dirty_ratio / dirty_background_ratio it isn't so
simple as the dirty limit is computed from the amount of available memory
which can change due to memory hotplug etc. So when converting dirty
limits from ratios to numbers of pages, we just don't allow the result to
exceed UINT_MAX.
This is root-only triggerable problem which occurs when the operator
sets dirty limits to >16 TB. |
| In the Linux kernel, the following vulnerability has been resolved:
NFSv4: Fix memory leak in nfs4_set_security_label
We leak nfs_fattr and nfs4_label every time we set a security xattr. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix uninitialized ratelimit_state->lock access in __ext4_fill_super()
In the following concurrency we will access the uninitialized rs->lock:
ext4_fill_super
ext4_register_sysfs
// sysfs registered msg_ratelimit_interval_ms
// Other processes modify rs->interval to
// non-zero via msg_ratelimit_interval_ms
ext4_orphan_cleanup
ext4_msg(sb, KERN_INFO, "Errors on filesystem, "
__ext4_msg
___ratelimit(&(EXT4_SB(sb)->s_msg_ratelimit_state)
if (!rs->interval) // do nothing if interval is 0
return 1;
raw_spin_trylock_irqsave(&rs->lock, flags)
raw_spin_trylock(lock)
_raw_spin_trylock
__raw_spin_trylock
spin_acquire(&lock->dep_map, 0, 1, _RET_IP_)
lock_acquire
__lock_acquire
register_lock_class
assign_lock_key
dump_stack();
ratelimit_state_init(&sbi->s_msg_ratelimit_state, 5 * HZ, 10);
raw_spin_lock_init(&rs->lock);
// init rs->lock here
and get the following dump_stack:
=========================================================
INFO: trying to register non-static key.
The code is fine but needs lockdep annotation, or maybe
you didn't initialize this object before use?
turning off the locking correctness validator.
CPU: 12 PID: 753 Comm: mount Tainted: G E 6.7.0-rc6-next-20231222 #504
[...]
Call Trace:
dump_stack_lvl+0xc5/0x170
dump_stack+0x18/0x30
register_lock_class+0x740/0x7c0
__lock_acquire+0x69/0x13a0
lock_acquire+0x120/0x450
_raw_spin_trylock+0x98/0xd0
___ratelimit+0xf6/0x220
__ext4_msg+0x7f/0x160 [ext4]
ext4_orphan_cleanup+0x665/0x740 [ext4]
__ext4_fill_super+0x21ea/0x2b10 [ext4]
ext4_fill_super+0x14d/0x360 [ext4]
[...]
=========================================================
Normally interval is 0 until s_msg_ratelimit_state is initialized, so
___ratelimit() does nothing. But registering sysfs precedes initializing
rs->lock, so it is possible to change rs->interval to a non-zero value
via the msg_ratelimit_interval_ms interface of sysfs while rs->lock is
uninitialized, and then a call to ext4_msg triggers the problem by
accessing an uninitialized rs->lock. Therefore register sysfs after all
initializations are complete to avoid such problems. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/radeon: fix UBSAN warning in kv_dpm.c
Adds bounds check for sumo_vid_mapping_entry. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: lpfc: Move NPIV's transport unregistration to after resource clean up
There are cases after NPIV deletion where the fabric switch still believes
the NPIV is logged into the fabric. This occurs when a vport is
unregistered before the Remove All DA_ID CT and LOGO ELS are sent to the
fabric.
Currently fc_remove_host(), which calls dev_loss_tmo for all D_IDs including
the fabric D_ID, removes the last ndlp reference and frees the ndlp rport
object. This sometimes causes the race condition where the final DA_ID and
LOGO are skipped from being sent to the fabric switch.
Fix by moving the fc_remove_host() and scsi_remove_host() calls after DA_ID
and LOGO are sent. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: lpfc: Release hbalock before calling lpfc_worker_wake_up()
lpfc_worker_wake_up() calls the lpfc_work_done() routine, which takes the
hbalock. Thus, lpfc_worker_wake_up() should not be called while holding the
hbalock to avoid potential deadlock. |
| In the Linux kernel, the following vulnerability has been resolved:
dyndbg: fix old BUG_ON in >control parser
Fix a BUG_ON from 2009. Even if it looks "unreachable" (I didn't
really look), lets make sure by removing it, doing pr_err and return
-EINVAL instead. |
| In the Linux kernel, the following vulnerability has been resolved:
PCI/PM: Drain runtime-idle callbacks before driver removal
A race condition between the .runtime_idle() callback and the .remove()
callback in the rtsx_pcr PCI driver leads to a kernel crash due to an
unhandled page fault [1].
The problem is that rtsx_pci_runtime_idle() is not expected to be running
after pm_runtime_get_sync() has been called, but the latter doesn't really
guarantee that. It only guarantees that the suspend and resume callbacks
will not be running when it returns.
However, if a .runtime_idle() callback is already running when
pm_runtime_get_sync() is called, the latter will notice that the runtime PM
status of the device is RPM_ACTIVE and it will return right away without
waiting for the former to complete. In fact, it cannot wait for
.runtime_idle() to complete because it may be called from that callback (it
arguably does not make much sense to do that, but it is not strictly
prohibited).
Thus in general, whoever is providing a .runtime_idle() callback needs
to protect it from running in parallel with whatever code runs after
pm_runtime_get_sync(). [Note that .runtime_idle() will not start after
pm_runtime_get_sync() has returned, but it may continue running then if it
has started earlier.]
One way to address that race condition is to call pm_runtime_barrier()
after pm_runtime_get_sync() (not before it, because a nonzero value of the
runtime PM usage counter is necessary to prevent runtime PM callbacks from
being invoked) to wait for the .runtime_idle() callback to complete should
it be running at that point. A suitable place for doing that is in
pci_device_remove() which calls pm_runtime_get_sync() before removing the
driver, so it may as well call pm_runtime_barrier() subsequently, which
will prevent the race in question from occurring, not just in the rtsx_pcr
driver, but in any PCI drivers providing .runtime_idle() callbacks. |
| In the Linux kernel, the following vulnerability has been resolved:
nvme-fc: do not wait in vain when unloading module
The module exit path has race between deleting all controllers and
freeing 'left over IDs'. To prevent double free a synchronization
between nvme_delete_ctrl and ida_destroy has been added by the initial
commit.
There is some logic around trying to prevent from hanging forever in
wait_for_completion, though it does not handling all cases. E.g.
blktests is able to reproduce the situation where the module unload
hangs forever.
If we completely rely on the cleanup code executed from the
nvme_delete_ctrl path, all IDs will be freed eventually. This makes
calling ida_destroy unnecessary. We only have to ensure that all
nvme_delete_ctrl code has been executed before we leave
nvme_fc_exit_module. This is done by flushing the nvme_delete_wq
workqueue.
While at it, remove the unused nvme_fc_wq workqueue too. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/proc: do_task_stat: use sig->stats_lock to gather the threads/children stats
lock_task_sighand() can trigger a hard lockup. If NR_CPUS threads call
do_task_stat() at the same time and the process has NR_THREADS, it will
spin with irqs disabled O(NR_CPUS * NR_THREADS) time.
Change do_task_stat() to use sig->stats_lock to gather the statistics
outside of ->siglock protected section, in the likely case this code will
run lockless. |
| In the Linux kernel, the following vulnerability has been resolved:
blk-mq: fix IO hang from sbitmap wakeup race
In blk_mq_mark_tag_wait(), __add_wait_queue() may be re-ordered
with the following blk_mq_get_driver_tag() in case of getting driver
tag failure.
Then in __sbitmap_queue_wake_up(), waitqueue_active() may not observe
the added waiter in blk_mq_mark_tag_wait() and wake up nothing, meantime
blk_mq_mark_tag_wait() can't get driver tag successfully.
This issue can be reproduced by running the following test in loop, and
fio hang can be observed in < 30min when running it on my test VM
in laptop.
modprobe -r scsi_debug
modprobe scsi_debug delay=0 dev_size_mb=4096 max_queue=1 host_max_queue=1 submit_queues=4
dev=`ls -d /sys/bus/pseudo/drivers/scsi_debug/adapter*/host*/target*/*/block/* | head -1 | xargs basename`
fio --filename=/dev/"$dev" --direct=1 --rw=randrw --bs=4k --iodepth=1 \
--runtime=100 --numjobs=40 --time_based --name=test \
--ioengine=libaio
Fix the issue by adding one explicit barrier in blk_mq_mark_tag_wait(), which
is just fine in case of running out of tag. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: iscsi_tcp: Fix UAF during login when accessing the shost ipaddress
If during iscsi_sw_tcp_session_create() iscsi_tcp_r2tpool_alloc() fails,
userspace could be accessing the host's ipaddress attr. If we then free the
session via iscsi_session_teardown() while userspace is still accessing the
session we will hit a use after free bug.
Set the tcp_sw_host->session after we have completed session creation and
can no longer fail. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: ibmvfc: Remove BUG_ON in the case of an empty event pool
In practice the driver should never send more commands than are allocated
to a queue's event pool. In the unlikely event that this happens, the code
asserts a BUG_ON, and in the case that the kernel is not configured to
crash on panic returns a junk event pointer from the empty event list
causing things to spiral from there. This BUG_ON is a historical artifact
of the ibmvfc driver first being upstreamed, and it is well known now that
the use of BUG_ON is bad practice except in the most unrecoverable
scenario. There is nothing about this scenario that prevents the driver
from recovering and carrying on.
Remove the BUG_ON in question from ibmvfc_get_event() and return a NULL
pointer in the case of an empty event pool. Update all call sites to
ibmvfc_get_event() to check for a NULL pointer and perfrom the appropriate
failure or recovery action. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: libfc: Fix potential NULL pointer dereference in fc_lport_ptp_setup()
fc_lport_ptp_setup() did not check the return value of fc_rport_create()
which can return NULL and would cause a NULL pointer dereference. Address
this issue by checking return value of fc_rport_create() and log error
message on fc_rport_create() failed. |
| In the Linux kernel, the following vulnerability has been resolved:
virtio-blk: fix implicit overflow on virtio_max_dma_size
The following codes have an implicit conversion from size_t to u32:
(u32)max_size = (size_t)virtio_max_dma_size(vdev);
This may lead overflow, Ex (size_t)4G -> (u32)0. Once
virtio_max_dma_size() has a larger size than U32_MAX, use U32_MAX
instead. |
| In the Linux kernel, the following vulnerability has been resolved:
can: j1939: prevent deadlock by changing j1939_socks_lock to rwlock
The following 3 locks would race against each other, causing the
deadlock situation in the Syzbot bug report:
- j1939_socks_lock
- active_session_list_lock
- sk_session_queue_lock
A reasonable fix is to change j1939_socks_lock to an rwlock, since in
the rare situations where a write lock is required for the linked list
that j1939_socks_lock is protecting, the code does not attempt to
acquire any more locks. This would break the circular lock dependency,
where, for example, the current thread already locks j1939_socks_lock
and attempts to acquire sk_session_queue_lock, and at the same time,
another thread attempts to acquire j1939_socks_lock while holding
sk_session_queue_lock.
NOTE: This patch along does not fix the unregister_netdevice bug
reported by Syzbot; instead, it solves a deadlock situation to prepare
for one or more further patches to actually fix the Syzbot bug, which
appears to be a reference counting problem within the j1939 codebase.
[mkl: remove unrelated newline change] |
| In the Linux kernel, the following vulnerability has been resolved:
PM / devfreq: Synchronize devfreq_monitor_[start/stop]
There is a chance if a frequent switch of the governor
done in a loop result in timer list corruption where
timer cancel being done from two place one from
cancel_delayed_work_sync() and followed by expire_timers()
can be seen from the traces[1].
while true
do
echo "simple_ondemand" > /sys/class/devfreq/1d84000.ufshc/governor
echo "performance" > /sys/class/devfreq/1d84000.ufshc/governor
done
It looks to be issue with devfreq driver where
device_monitor_[start/stop] need to synchronized so that
delayed work should get corrupted while it is either
being queued or running or being cancelled.
Let's use polling flag and devfreq lock to synchronize the
queueing the timer instance twice and work data being
corrupted.
[1]
...
..
<idle>-0 [003] 9436.209662: timer_cancel timer=0xffffff80444f0428
<idle>-0 [003] 9436.209664: timer_expire_entry timer=0xffffff80444f0428 now=0x10022da1c function=__typeid__ZTSFvP10timer_listE_global_addr baseclk=0x10022da1c
<idle>-0 [003] 9436.209718: timer_expire_exit timer=0xffffff80444f0428
kworker/u16:6-14217 [003] 9436.209863: timer_start timer=0xffffff80444f0428 function=__typeid__ZTSFvP10timer_listE_global_addr expires=0x10022da2b now=0x10022da1c flags=182452227
vendor.xxxyyy.ha-1593 [004] 9436.209888: timer_cancel timer=0xffffff80444f0428
vendor.xxxyyy.ha-1593 [004] 9436.216390: timer_init timer=0xffffff80444f0428
vendor.xxxyyy.ha-1593 [004] 9436.216392: timer_start timer=0xffffff80444f0428 function=__typeid__ZTSFvP10timer_listE_global_addr expires=0x10022da2c now=0x10022da1d flags=186646532
vendor.xxxyyy.ha-1593 [005] 9436.220992: timer_cancel timer=0xffffff80444f0428
xxxyyyTraceManag-7795 [004] 9436.261641: timer_cancel timer=0xffffff80444f0428
[2]
9436.261653][ C4] Unable to handle kernel paging request at virtual address dead00000000012a
[ 9436.261664][ C4] Mem abort info:
[ 9436.261666][ C4] ESR = 0x96000044
[ 9436.261669][ C4] EC = 0x25: DABT (current EL), IL = 32 bits
[ 9436.261671][ C4] SET = 0, FnV = 0
[ 9436.261673][ C4] EA = 0, S1PTW = 0
[ 9436.261675][ C4] Data abort info:
[ 9436.261677][ C4] ISV = 0, ISS = 0x00000044
[ 9436.261680][ C4] CM = 0, WnR = 1
[ 9436.261682][ C4] [dead00000000012a] address between user and kernel address ranges
[ 9436.261685][ C4] Internal error: Oops: 96000044 [#1] PREEMPT SMP
[ 9436.261701][ C4] Skip md ftrace buffer dump for: 0x3a982d0
...
[ 9436.262138][ C4] CPU: 4 PID: 7795 Comm: TraceManag Tainted: G S W O 5.10.149-android12-9-o-g17f915d29d0c #1
[ 9436.262141][ C4] Hardware name: Qualcomm Technologies, Inc. (DT)
[ 9436.262144][ C4] pstate: 22400085 (nzCv daIf +PAN -UAO +TCO BTYPE=--)
[ 9436.262161][ C4] pc : expire_timers+0x9c/0x438
[ 9436.262164][ C4] lr : expire_timers+0x2a4/0x438
[ 9436.262168][ C4] sp : ffffffc010023dd0
[ 9436.262171][ C4] x29: ffffffc010023df0 x28: ffffffd0636fdc18
[ 9436.262178][ C4] x27: ffffffd063569dd0 x26: ffffffd063536008
[ 9436.262182][ C4] x25: 0000000000000001 x24: ffffff88f7c69280
[ 9436.262185][ C4] x23: 00000000000000e0 x22: dead000000000122
[ 9436.262188][ C4] x21: 000000010022da29 x20: ffffff8af72b4e80
[ 9436.262191][ C4] x19: ffffffc010023e50 x18: ffffffc010025038
[ 9436.262195][ C4] x17: 0000000000000240 x16: 0000000000000201
[ 9436.262199][ C4] x15: ffffffffffffffff x14: ffffff889f3c3100
[ 9436.262203][ C4] x13: ffffff889f3c3100 x12: 00000000049f56b8
[ 9436.262207][ C4] x11: 00000000049f56b8 x10: 00000000ffffffff
[ 9436.262212][ C4] x9 : ffffffc010023e50 x8 : dead000000000122
[ 9436.262216][ C4] x7 : ffffffffffffffff x6 : ffffffc0100239d8
[ 9436.262220][ C4] x5 : 0000000000000000 x4 : 0000000000000101
[ 9436.262223][ C4] x3 : 0000000000000080 x2 : ffffff8
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: avoid online resizing failures due to oversized flex bg
When we online resize an ext4 filesystem with a oversized flexbg_size,
mkfs.ext4 -F -G 67108864 $dev -b 4096 100M
mount $dev $dir
resize2fs $dev 16G
the following WARN_ON is triggered:
==================================================================
WARNING: CPU: 0 PID: 427 at mm/page_alloc.c:4402 __alloc_pages+0x411/0x550
Modules linked in: sg(E)
CPU: 0 PID: 427 Comm: resize2fs Tainted: G E 6.6.0-rc5+ #314
RIP: 0010:__alloc_pages+0x411/0x550
Call Trace:
<TASK>
__kmalloc_large_node+0xa2/0x200
__kmalloc+0x16e/0x290
ext4_resize_fs+0x481/0xd80
__ext4_ioctl+0x1616/0x1d90
ext4_ioctl+0x12/0x20
__x64_sys_ioctl+0xf0/0x150
do_syscall_64+0x3b/0x90
==================================================================
This is because flexbg_size is too large and the size of the new_group_data
array to be allocated exceeds MAX_ORDER. Currently, the minimum value of
MAX_ORDER is 8, the minimum value of PAGE_SIZE is 4096, the corresponding
maximum number of groups that can be allocated is:
(PAGE_SIZE << MAX_ORDER) / sizeof(struct ext4_new_group_data) ≈ 21845
And the value that is down-aligned to the power of 2 is 16384. Therefore,
this value is defined as MAX_RESIZE_BG, and the number of groups added
each time does not exceed this value during resizing, and is added multiple
times to complete the online resizing. The difference is that the metadata
in a flex_bg may be more dispersed. |
| In the Linux kernel, the following vulnerability has been resolved:
pstore/ram: Fix crash when setting number of cpus to an odd number
When the number of cpu cores is adjusted to 7 or other odd numbers,
the zone size will become an odd number.
The address of the zone will become:
addr of zone0 = BASE
addr of zone1 = BASE + zone_size
addr of zone2 = BASE + zone_size*2
...
The address of zone1/3/5/7 will be mapped to non-alignment va.
Eventually crashes will occur when accessing these va.
So, use ALIGN_DOWN() to make sure the zone size is even
to avoid this bug. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rt2x00: restart beacon queue when hardware reset
When a hardware reset is triggered, all registers are reset, so all
queues are forced to stop in hardware interface. However, mac80211
will not automatically stop the queue. If we don't manually stop the
beacon queue, the queue will be deadlocked and unable to start again.
This patch fixes the issue where Apple devices cannot connect to the
AP after calling ieee80211_restart_hw(). |
