| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
usb: cdns3: Fix NULL pointer dereference in cdns3_pci_probe
The Cadence USBSS controller is a two-function PCI device. The first
probed function allocates the driver data and stores it with
pci_set_drvdata(), while the second function reuses it via
pci_get_drvdata() when pci_is_enabled() reports that the first
function has already been probed.
When the second function is probed while the first one has been
enabled but has not yet set its driver data, pci_get_drvdata()
returns NULL, and the subsequent wrap->devfn assignment dereferences
a NULL pointer and crashes the kernel.
logs:
Call trace:
cdns3_pci_probe+0xa4/0x300
local_pci_probe+0x44/0xa8
pci_call_probe+0x54/0x158
pci_device_probe+0x84/0x100
really_probe+0x184/0x3d0
__driver_probe_device+0x80/0x178
driver_probe_device+0x44/0xe8
__driver_attach+0xec/0x1f8
bus_for_each_dev+0x7c/0xe0
driver_attach+0x28/0x38
bus_add_driver+0x110/0x238
driver_register+0x64/0x128
__pci_register_driver+0x50/0x60
cdns3_pci_driver_init+0x28/0x38
do_one_initcall+0x5c/0x280
do_initcalls+0x104/0x1d8
kernel_init_freeable+0x140/0x218
kernel_init+0x28/0x1f8
ret_from_fork+0x10/0x20
Return -EPROBE_DEFER in this case so that probing is retried after
the first function has completed its probe. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: fix ioctl hangup race
The tty ioctls can race with hangup and end up calling into a tty driver
for a device that is already gone or powered down.
Serialise the callbacks using the tty port mutex and add the missing
checks to make sure the port has not been hung up before accessing port
driver data or hardware.
This specifically avoids dereferencing a NULL-pointer if a device is
disconnected during lengthy break signalling.
Note that TIOCGICOUNT and TIOCMIWAIT do not access port driver data or
hardware and are therefore not affected by the race. |
| In the Linux kernel, the following vulnerability has been resolved:
erofs: preserve LZMA decoders on resize failure
The pool-resize path frees each stream's old decoder before allocating
its replacement. If an allocation fails after some streams have already
been replaced, the failed stream is put back on the list with state ==
NULL. z_erofs_lzma_max_dictsize is still advanced as if the whole
pool had been resized.
An existing LZMA mount can select the broken stream and pass
NULL to xz_dec_microlzma_reset(). A retry at the same size also
skip another resize attempt. Since the global maximum was advanced,
thus, the invalid state is left unrepaired.
Allocate each replacement before freeing the old decoder, temporarily
retaining one old decoder during allocation. Stop at the first failure
and advance z_erofs_lzma_max_dictsize only after all streams satisfy
the request.
Record each stream's dictionary capacity so retries can skip streams
already enlarged before a partial failure. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Fix queue teardown NULL dma_free and bitmap locking
qla25xx_free_req_que() and qla25xx_free_rsp_que() have two pre-existing
bugs exposed on the error path of qla25xx_create_{req,rsp}_que():
1. When dma_alloc_coherent() fails during queue creation, the error
path calls the free function with req->ring / rsp->ring still NULL
(from kzalloc). The unconditional dma_free_coherent() with a NULL
cpu_addr is undefined behavior and can panic.
2. The free functions clear req_qid_map / rsp_qid_map under vport_lock,
but the create functions protect the same bitmaps with mq_lock.
This provides no mutual exclusion. Additionally, the create error
path clears the bit and releases mq_lock before calling the free
function, creating a window where another thread can allocate the
same que_id and have its ha->req_q_map entry clobbered by the
subsequent lockless NULL assignment in the free function.
Fix by:
- Guarding dma_free_coherent() with a NULL check on the ring pointer.
- Using mq_lock (the lock held by all creators) in the free functions
to atomically NULL the map entry and clear the bitmap bit.
- Removing the now-redundant clear_bit blocks from the create error
paths since the free functions handle it atomically. |
| In the Linux kernel, the following vulnerability has been resolved:
tty: serial: 8250: protect against NULL uart->port.dev in register
serial8250_register_8250_port() conditionally copies uart->port.dev
from up->port.dev only when up->port.dev is non-NULL:
if (up->port.dev) {
uart->port.dev = up->port.dev;
...
}
So if both the existing uart slot and up have a NULL ->dev,
uart->port.dev remains NULL. The very next ACPI companion check
then dereferences it unconditionally:
if (!has_acpi_companion(uart->port.dev)) {
has_acpi_companion() reads dev->fwnode without a NULL guard
(include/linux/acpi.h), so this NULL-derefs the kernel for the
remaining no-dev case rather than just skipping the
mctrl_gpio_init() initialisation as intended.
smatch flags the inconsistency:
drivers/tty/serial/8250/8250_core.c:767
serial8250_register_8250_port() error: 'uart->port.dev' could be
null (see line 719)
Guard the call with a NULL check so register continues to work
for callers that legitimately have no parent device (legacy
non-OF/non-ACPI registrations).
No functional change for callers that pass a non-NULL ->dev. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: embed f2fs_gc_kthread in f2fs_sb_info
Instead of allocating f2fs_gc_kthread dynamically, embed it in
f2fs_sb_info. This simplifies lifetime management and prepares for
fixing race conditions during teardown.
- __sbi_store - remount|shutdown
- f2fs_stop_gc_thread
- access sbi->gc_thread
- sbi->gc_thread = NULL
- access sbi->gc_thread->f2fs_gc_task |
| In the Linux kernel, the following vulnerability has been resolved:
mm/mm_init: handle alloc_percpu failure in free_area_init_core_hotplug
We miss a failed allocation check for pgdat->per_cpu_nodestats, which
results in a NULL deref when we offset into the per-cpu area.
Propagate -ENOMEM up the stack and leave per_cpu_nodestats pointing
at boot_nodestats so a later online can retry the allocation.
hotadd_init_pgdat() returns NULL on failure, which __try_online_node()
already maps to -ENOMEM.
On failure nothing needs to be unwound:
- the node is never marked online
- per_cpu_nodestats is left pointing at boot_nodestats
- __add_memory_resource() cleans up pending memblock resources
- later online attempts retry the per_cpu_nodestats allocation |
| In the Linux kernel, the following vulnerability has been resolved:
platform/x86: lg-laptop: Fix LED resource handling
The event notification callback might access kbd_backlight even
when it was not successfully registered with the LED subsystem.
The same happens inside acpi_remove(), where the LED devices are
unregistered unconditionally.
Fix this by tracking the availability of the kbd_backlight LED
device and use devm_led_classdev_register() to let devres take
care of unregistering the LED devices during removal. For this
the parent device of the LED devices is changed to the native
platform device. |
| In the Linux kernel, the following vulnerability has been resolved:
firmware: arm_scmi: Publish channel state before callbacks
Transport setup can enable callbacks before the setup routine returns.
mailbox_chan_setup() registers the mailbox client with
mbox_request_channel(), and the mailbox controller startup path can enable
interrupt delivery before SCMI mailbox channel state has been published.
Similarly, smc_chan_setup() requests the optional A2P completion IRQ before
the SMC transport has made its cinfo pointer visible.
If a pending or spurious callback fires in those windows, the transport RX
callback can dereference a NULL transport cinfo pointer. Publishing only
the transport-private pointer is not sufficient either: an early callback
can enter the SCMI core before scmi_chan_setup() has assigned
cinfo->handle.
The core derives scmi_info from cinfo->handle in the RX path, so a NULL
handle can still fault even when the transport-private cinfo is valid.
Assign cinfo->handle before invoking the transport setup callback. Publish
the mailbox and SMC transport-private channel state before requesting the
mailbox channels or IRQ, and clear the early-published pointers again on
setup failure. Also unwind mailbox setup devres resources on failure so an
optional RX setup error that is ignored by the core does not leave stale
transport state behind. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: fix P2P action frame handling without device vif
Some P2P action frame paths assume the P2P device vif is always
available. That is not true when userspace sends non-P2P public action
frames through the primary interface, or when action-frame abort runs
after the P2P device vif has not been created.
Fall back to the primary vif when aborting an action frame without a P2P
device vif, and guard P2P device saved IE access before using it for
peer channel search. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: core: do fallible allocations before the console can be registered
serial_core_add_one_port() allocates uport->tty_groups after
uart_configure_port(), which may register the console. If the allocation
fails, the driver unwinds the port while its console remains registered.
The earlier uport->name allocation has a related failure path that leaves
state->uart_port linked to a port being freed.
Failslab reproduced a NULL dereference in PL011 console output and a KASAN
use-after-free in i.MX console output after failed binds.
Allocate the name and tty_groups before linking the port and configuring
it. Reserve space for the optional driver attribute group because
config_port() may populate uport->attr_group during configuration. |
| In the Linux kernel, the following vulnerability has been resolved:
tty: skip cdev_del() when no cdev is registered
TTY device registration can fail before a cdev is allocated.
Serial core keeps the port so setserial can still use it, and later
removal passes the NULL cdev slot to cdev_del(), causing a NULL-pointer
dereference.
Only delete the cdev when the slot is not NULL. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf, cgroup: Fix storage null-ptr-deref after replacing prog
Syzkaller reported a storage null-ptr-deref issue after replacing prog.
This occurs in the following scenario:
1. prog A, an empty prog, is attached to a cgrp.
2. prog B uses BPF_MAP_TYPE_PERCPU_CGROUP_STORAGE and calls the
bpf_get_local_storage helper.
3. link_update is called to replace prog A with prog B.
The reason is that __cgroup_bpf_replace fails to alloc and assign the
required cgrp storage for the incoming replacement prog. Consequently,
the new prog inherits an uninit storage, leading to null-ptr-deref panic
when kick the new prog.
Fix this by rejecting a link update if new_prog's cgroup storage is
incompatible with link->prog. |
| In the Linux kernel, the following vulnerability has been resolved:
smb/server: fix null-ptr-deref in ksmbd_ipc_tree_connect_request()
See the procedure below:
ksmbd_tree_conn_connect
ksmbd_share_config_get
share->name = kstrdup() // fail
if (!test_share_config_flag(share, KSMBD_SHARE_FLAG_PIPE)) // false
// do not check `share->name`
ksmbd_ipc_tree_connect_request
strlen(share->name) // null-ptr-deref |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: safely discard unregistered deferred locks
When vfs_lock_file() defers a lock, smb2_lock() puts its ksmbd_lock on
rollback_list before allocating and registering the asynchronous work.
If either operation fails, rollback assumes that smb_lock->conn is
initialized and dereferences NULL. The deferred file_lock also remains
linked into the VFS blocked-lock state while it is freed.
Keep the lock off rollback_list until async setup succeeds. On setup
failures, explicitly unblock and wake the deferred lock before freeing it
and its ksmbd wrapper. |
| In the Linux kernel, the following vulnerability has been resolved:
NFSv4/flexfiles: fix NULL dereference for NFSv4.0 data servers
flexfiles accepts NFSv4.0 data servers, but two NFSv4 code paths assume
the data server client has a session. Unlike NFSv4.1+, an NFSv4.0 client
has no session (clp->cl_session is NULL; it uses clp->cl_slot_tbl), so
I/O to a v4.0 flexfiles DS oopses:
- nfs4_init_ds_session() dereferences clp->cl_session->session_state
while seeding the DS lease. It also only seeds cl_lease_time when
NFS4_SESSION_INITING is set; without a session that never happens, so
cl_lease_time stays 0 and nfs4_renew_state() busy-loops, requeuing
every 5 seconds. Seed the lease whenever there is no session and
return before touching session state.
- ff_layout_async_handle_error_v4() dereferences
clp->cl_session->fc_slot_table on every DS I/O error. Fall back to the
v4.0 transport slot table (clp->cl_slot_tbl) when there is no session. |
| In the Linux kernel, the following vulnerability has been resolved:
NFSv4: Fix incorrect argument passed to nfs4_delete_lease() in nfs4_add_lease()
When nfs4_add_lease() races with a delegation return, it calls
nfs4_delete_lease() to clean up. Previously, it passed priv,
which can legitimately be NULL. Passing a NULL priv eventually
leads to a NULL pointer dereference in generic_setlease(). |
| In the Linux kernel, the following vulnerability has been resolved:
fuse: check for NULL root inode in fuse_fill_super_submount
fuse_iget() can return NULL when its inode allocation fails, but
fuse_fill_super_submount() passed the result straight to get_fuse_inode()
and decremented fi->nlookup without checking it:
root = fuse_iget(sb, parent_fi->nodeid, ...);
fi = get_fuse_inode(root);
fi->nlookup--;
Inside fuse_iget() the inode allocation can fail and return NULL. The
submount root takes the iget5_locked() path, whose alloc_inode() can fail
under memory pressure (the auto-submount branch can fail the same way in
new_inode() or fuse_alloc_submount_lookup()):
inode = iget5_locked(sb, nodeid, fuse_inode_eq, fuse_inode_set,
&nodeid);
if (!inode)
return NULL;
A NULL root makes get_fuse_inode() a container_of() on NULL and the
nlookup decrement a write to a bogus address, oopsing the mount. With
CONFIG_KASAN the following null pointer dereference is reported when the
root inode allocation of an auto-submount fails (e.g. under memory
pressure):
==================================================================
BUG: KASAN: null-ptr-deref in fuse_get_tree_submount+0x656/0x8b0
Read of size 8 at addr 00000000000002b0 by task ls/942
CPU: 0 PID: 942 Comm: ls Tainted: G W 6.6 #15
Call Trace:
<TASK>
fuse_get_tree_submount+0x656/0x8b0
vfs_get_tree+0x48/0x140
fc_mount+0x13/0x50
fuse_dentry_automount+0x7a/0xb0
__traverse_mounts+0xca/0x330
step_into+0x339/0xac0
path_lookupat+0xc5/0x2f0
filename_lookup+0x163/0x2a0
vfs_statx+0xd5/0x200
do_statx+0x83/0xd0
__x64_sys_statx+0xa0/0xc0
do_syscall_64+0x37/0x90
entry_SYSCALL_64_after_hwframe+0x78/0xe2
</TASK>
==================================================================
Return -ENOMEM instead; the caller tears down the partially built
superblock on error, matching the other error returns in this
function. |
| In the Linux kernel, the following vulnerability has been resolved:
octeontx2-vf: fix workqueue and netdev race in probe/remove
Initialize the VF workqueue before register_netdev() so ndo_set_rx_mode
does not queue work on a NULL workqueue. Unregister the netdev before
destroying the workqueue, and add proper probe error cleanup. |
| In the Linux kernel, the following vulnerability has been resolved:
samples/ftrace: Fix kthread_stop() on ERR_PTR in ftrace-direct-multi-modify
ftrace_direct_multi_init() assigns kthread_run()'s return value to
simple_tsk without an IS_ERR() check. When kthread_run() fails it
returns ERR_PTR(-ENOMEM), but init still returns 0, so the module loads
with simple_tsk holding an error pointer. On unload,
ftrace_direct_multi_exit() then passes that ERR_PTR to kthread_stop(),
leading to a null-pointer-dereference.
Check the return value of kthread_run() with IS_ERR(); on failure,
unregister the ftrace direct call and propagate the error code. |