| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: dsa: bcm_sf2: don't use devres for mdiobus
As explained in commits:
74b6d7d13307 ("net: dsa: realtek: register the MDIO bus under devres")
5135e96a3dd2 ("net: dsa: don't allocate the slave_mii_bus using devres")
mdiobus_free() will panic when called from devm_mdiobus_free() <-
devres_release_all() <- __device_release_driver(), and that mdiobus was
not previously unregistered.
The Starfighter 2 is a platform device, so the initial set of
constraints that I thought would cause this (I2C or SPI buses which call
->remove on ->shutdown) do not apply. But there is one more which
applies here.
If the DSA master itself is on a bus that calls ->remove from ->shutdown
(like dpaa2-eth, which is on the fsl-mc bus), there is a device link
between the switch and the DSA master, and device_links_unbind_consumers()
will unbind the bcm_sf2 switch driver on shutdown.
So the same treatment must be applied to all DSA switch drivers, which
is: either use devres for both the mdiobus allocation and registration,
or don't use devres at all.
The bcm_sf2 driver has the code structure in place for orderly mdiobus
removal, so just replace devm_mdiobus_alloc() with the non-devres
variant, and add manual free where necessary, to ensure that we don't
let devres free a still-registered bus. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/mipi-dsi: Detach devices when removing the host
Whenever the MIPI-DSI host is unregistered, the code of
mipi_dsi_host_unregister() loops over every device currently found on that
bus and will unregister it.
However, it doesn't detach it from the bus first, which leads to all kind
of resource leaks if the host wants to perform some clean up whenever a
device is detached. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/s390: Fix memory corruption when using identity domain
zpci_get_iommu_ctrs() returns counter information to be reported as part
of device statistics; these counters are stored as part of the s390_domain.
The problem, however, is that the identity domain is not backed by an
s390_domain and so the conversion via to_s390_domain() yields a bad address
that is zero'd initially and read on-demand later via a sysfs read.
These counters aren't necessary for the identity domain; just return NULL
in this case.
This issue was discovered via KASAN with reports that look like:
BUG: KASAN: global-out-of-bounds in zpci_fmb_enable_device
when using the identity domain for a device on s390. |
| In the Linux kernel, the following vulnerability has been resolved:
cxl: fix possible null-ptr-deref in cxl_guest_init_afu|adapter()
If device_register() fails in cxl_register_afu|adapter(), the device
is not added, device_unregister() can not be called in the error path,
otherwise it will cause a null-ptr-deref because of removing not added
device.
As comment of device_register() says, it should use put_device() to give
up the reference in the error path. So split device_unregister() into
device_del() and put_device(), then goes to put dev when register fails. |
| In the Linux kernel, the following vulnerability has been resolved:
qed: Don't collect too many protection override GRC elements
In the protection override dump path, the firmware can return far too
many GRC elements, resulting in attempting to write past the end of the
previously-kmalloc'ed dump buffer.
This will result in a kernel panic with reason:
BUG: unable to handle kernel paging request at ADDRESS
where "ADDRESS" is just past the end of the protection override dump
buffer. The start address of the buffer is:
p_hwfn->cdev->dbg_features[DBG_FEATURE_PROTECTION_OVERRIDE].dump_buf
and the size of the buffer is buf_size in the same data structure.
The panic can be arrived at from either the qede Ethernet driver path:
[exception RIP: qed_grc_dump_addr_range+0x108]
qed_protection_override_dump at ffffffffc02662ed [qed]
qed_dbg_protection_override_dump at ffffffffc0267792 [qed]
qed_dbg_feature at ffffffffc026aa8f [qed]
qed_dbg_all_data at ffffffffc026b211 [qed]
qed_fw_fatal_reporter_dump at ffffffffc027298a [qed]
devlink_health_do_dump at ffffffff82497f61
devlink_health_report at ffffffff8249cf29
qed_report_fatal_error at ffffffffc0272baf [qed]
qede_sp_task at ffffffffc045ed32 [qede]
process_one_work at ffffffff81d19783
or the qedf storage driver path:
[exception RIP: qed_grc_dump_addr_range+0x108]
qed_protection_override_dump at ffffffffc068b2ed [qed]
qed_dbg_protection_override_dump at ffffffffc068c792 [qed]
qed_dbg_feature at ffffffffc068fa8f [qed]
qed_dbg_all_data at ffffffffc0690211 [qed]
qed_fw_fatal_reporter_dump at ffffffffc069798a [qed]
devlink_health_do_dump at ffffffff8aa95e51
devlink_health_report at ffffffff8aa9ae19
qed_report_fatal_error at ffffffffc0697baf [qed]
qed_hw_err_notify at ffffffffc06d32d7 [qed]
qed_spq_post at ffffffffc06b1011 [qed]
qed_fcoe_destroy_conn at ffffffffc06b2e91 [qed]
qedf_cleanup_fcport at ffffffffc05e7597 [qedf]
qedf_rport_event_handler at ffffffffc05e7bf7 [qedf]
fc_rport_work at ffffffffc02da715 [libfc]
process_one_work at ffffffff8a319663
Resolve this by clamping the firmware's return value to the maximum
number of legal elements the firmware should return. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd: fix potential memory leak
This patch fix potential memory leak (clk_src) when function run
into last return NULL.
s/free/kfree/ - Alex |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/core: Make sure "ib_port" is valid when access sysfs node
The "ib_port" structure must be set before adding the sysfs kobject,
and reset after removing it, otherwise it may crash when accessing
the sysfs node:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000050
Mem abort info:
ESR = 0x96000006
Exception class = DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000006
CM = 0, WnR = 0
user pgtable: 4k pages, 48-bit VAs, pgdp = 00000000e85f5ba5
[0000000000000050] pgd=0000000848fd9003, pud=000000085b387003, pmd=0000000000000000
Internal error: Oops: 96000006 [#2] PREEMPT SMP
Modules linked in: ib_umad(O) mlx5_ib(O) nfnetlink_cttimeout(E) nfnetlink(E) act_gact(E) cls_flower(E) sch_ingress(E) openvswitch(E) nsh(E) nf_nat_ipv6(E) nf_nat_ipv4(E) nf_conncount(E) nf_nat(E) nf_conntrack(E) nf_defrag_ipv6(E) nf_defrag_ipv4(E) mst_pciconf(O) ipmi_devintf(E) ipmi_msghandler(E) ipmb_dev_int(OE) mlx5_core(O) mlxfw(O) mlxdevm(O) auxiliary(O) ib_uverbs(O) ib_core(O) mlx_compat(O) psample(E) sbsa_gwdt(E) uio_pdrv_genirq(E) uio(E) mlxbf_pmc(OE) mlxbf_gige(OE) mlxbf_tmfifo(OE) gpio_mlxbf2(OE) pwr_mlxbf(OE) mlx_trio(OE) i2c_mlxbf(OE) mlx_bootctl(OE) bluefield_edac(OE) knem(O) ip_tables(E) ipv6(E) crc_ccitt(E) [last unloaded: mst_pci]
Process grep (pid: 3372, stack limit = 0x0000000022055c92)
CPU: 5 PID: 3372 Comm: grep Tainted: G D OE 4.19.161-mlnx.47.gadcd9e3 #1
Hardware name: https://www.mellanox.com BlueField SoC/BlueField SoC, BIOS BlueField:3.9.2-15-ga2403ab Sep 8 2022
pstate: 40000005 (nZcv daif -PAN -UAO)
pc : hw_stat_port_show+0x4c/0x80 [ib_core]
lr : port_attr_show+0x40/0x58 [ib_core]
sp : ffff000029f43b50
x29: ffff000029f43b50 x28: 0000000019375000
x27: ffff8007b821a540 x26: ffff000029f43e30
x25: 0000000000008000 x24: ffff000000eaa958
x23: 0000000000001000 x22: ffff8007a4ce3000
x21: ffff8007baff8000 x20: ffff8007b9066ac0
x19: ffff8007bae97578 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000
x15: 0000000000000000 x14: 0000000000000000
x13: 0000000000000000 x12: 0000000000000000
x11: 0000000000000000 x10: 0000000000000000
x9 : 0000000000000000 x8 : ffff8007a4ce4000
x7 : 0000000000000000 x6 : 000000000000003f
x5 : ffff000000e6a280 x4 : ffff8007a4ce3000
x3 : 0000000000000000 x2 : aaaaaaaaaaaaaaab
x1 : ffff8007b9066a10 x0 : ffff8007baff8000
Call trace:
hw_stat_port_show+0x4c/0x80 [ib_core]
port_attr_show+0x40/0x58 [ib_core]
sysfs_kf_seq_show+0x8c/0x150
kernfs_seq_show+0x44/0x50
seq_read+0x1b4/0x45c
kernfs_fop_read+0x148/0x1d8
__vfs_read+0x58/0x180
vfs_read+0x94/0x154
ksys_read+0x68/0xd8
__arm64_sys_read+0x28/0x34
el0_svc_common+0x88/0x18c
el0_svc_handler+0x78/0x94
el0_svc+0x8/0xe8
Code: f2955562 aa1603e4 aa1503e0 f9405683 (f9402861) |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: smbdirect: verify remaining_data_length respects max_fragmented_recv_size
This is inspired by the check for data_offset + data_length. |
| In the Linux kernel, the following vulnerability has been resolved:
zram: fix slot write race condition
Parallel concurrent writes to the same zram index result in leaked
zsmalloc handles. Schematically we can have something like this:
CPU0 CPU1
zram_slot_lock()
zs_free(handle)
zram_slot_lock()
zram_slot_lock()
zs_free(handle)
zram_slot_lock()
compress compress
handle = zs_malloc() handle = zs_malloc()
zram_slot_lock
zram_set_handle(handle)
zram_slot_lock
zram_slot_lock
zram_set_handle(handle)
zram_slot_lock
Either CPU0 or CPU1 zsmalloc handle will leak because zs_free() is done
too early. In fact, we need to reset zram entry right before we set its
new handle, all under the same slot lock scope. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix smbdirect_recv_io leak in smbd_negotiate() error path
During tests of another unrelated patch I was able to trigger this
error: Objects remaining on __kmem_cache_shutdown() |
| In the Linux kernel, the following vulnerability has been resolved:
um: virtio_uml: Fix use-after-free after put_device in probe
When register_virtio_device() fails in virtio_uml_probe(),
the code sets vu_dev->registered = 1 even though
the device was not successfully registered.
This can lead to use-after-free or other issues. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: smbdirect: validate data_offset and data_length field of smb_direct_data_transfer
If data_offset and data_length of smb_direct_data_transfer struct are
invalid, out of bounds issue could happen.
This patch validate data_offset and data_length field in recv_done. |
| In the Linux kernel, the following vulnerability has been resolved:
cpufreq: Init completion before kobject_init_and_add()
In cpufreq_policy_alloc(), it will call uninitialed completion in
cpufreq_sysfs_release() when kobject_init_and_add() fails. And
that will cause a crash such as the following page fault in complete:
BUG: unable to handle page fault for address: fffffffffffffff8
[..]
RIP: 0010:complete+0x98/0x1f0
[..]
Call Trace:
kobject_put+0x1be/0x4c0
cpufreq_online.cold+0xee/0x1fd
cpufreq_add_dev+0x183/0x1e0
subsys_interface_register+0x3f5/0x4e0
cpufreq_register_driver+0x3b7/0x670
acpi_cpufreq_init+0x56c/0x1000 [acpi_cpufreq]
do_one_initcall+0x13d/0x780
do_init_module+0x1c3/0x630
load_module+0x6e67/0x73b0
__do_sys_finit_module+0x181/0x240
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x63/0xcd |
| In the Linux kernel, the following vulnerability has been resolved:
macintosh: fix possible memory leak in macio_add_one_device()
Afer commit 1fa5ae857bb1 ("driver core: get rid of struct device's
bus_id string array"), the name of device is allocated dynamically. It
needs to be freed when of_device_register() fails. Call put_device() to
give up the reference that's taken in device_initialize(), so that it
can be freed in kobject_cleanup() when the refcount hits 0.
macio device is freed in macio_release_dev(), so the kfree() can be
removed. |
| In the Linux kernel, the following vulnerability has been resolved:
cnic: Fix use-after-free bugs in cnic_delete_task
The original code uses cancel_delayed_work() in cnic_cm_stop_bnx2x_hw(),
which does not guarantee that the delayed work item 'delete_task' has
fully completed if it was already running. Additionally, the delayed work
item is cyclic, the flush_workqueue() in cnic_cm_stop_bnx2x_hw() only
blocks and waits for work items that were already queued to the
workqueue prior to its invocation. Any work items submitted after
flush_workqueue() is called are not included in the set of tasks that the
flush operation awaits. This means that after the cyclic work items have
finished executing, a delayed work item may still exist in the workqueue.
This leads to use-after-free scenarios where the cnic_dev is deallocated
by cnic_free_dev(), while delete_task remains active and attempt to
dereference cnic_dev in cnic_delete_task().
A typical race condition is illustrated below:
CPU 0 (cleanup) | CPU 1 (delayed work callback)
cnic_netdev_event() |
cnic_stop_hw() | cnic_delete_task()
cnic_cm_stop_bnx2x_hw() | ...
cancel_delayed_work() | /* the queue_delayed_work()
flush_workqueue() | executes after flush_workqueue()*/
| queue_delayed_work()
cnic_free_dev(dev)//free | cnic_delete_task() //new instance
| dev = cp->dev; //use
Replace cancel_delayed_work() with cancel_delayed_work_sync() to ensure
that the cyclic delayed work item is properly canceled and that any
ongoing execution of the work item completes before the cnic_dev is
deallocated. Furthermore, since cancel_delayed_work_sync() uses
__flush_work(work, true) to synchronously wait for any currently
executing instance of the work item to finish, the flush_workqueue()
becomes redundant and should be removed.
This bug was identified through static analysis. To reproduce the issue
and validate the fix, I simulated the cnic PCI device in QEMU and
introduced intentional delays — such as inserting calls to ssleep()
within the cnic_delete_task() function — to increase the likelihood
of triggering the bug. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: af_alg - Set merge to zero early in af_alg_sendmsg
If an error causes af_alg_sendmsg to abort, ctx->merge may contain
a garbage value from the previous loop. This may then trigger a
crash on the next entry into af_alg_sendmsg when it attempts to do
a merge that can't be done.
Fix this by setting ctx->merge to zero near the start of the loop. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/vt-d: Clean up si_domain in the init_dmars() error path
A splat from kmem_cache_destroy() was seen with a kernel prior to
commit ee2653bbe89d ("iommu/vt-d: Remove domain and devinfo mempool")
when there was a failure in init_dmars(), because the iommu_domain
cache still had objects. While the mempool code is now gone, there
still is a leak of the si_domain memory if init_dmars() fails. So
clean up si_domain in the init_dmars() error path. |
| In the Linux kernel, the following vulnerability has been resolved:
net/tcp: Fix a NULL pointer dereference when using TCP-AO with TCP_REPAIR
A NULL pointer dereference can occur in tcp_ao_finish_connect() during a
connect() system call on a socket with a TCP-AO key added and TCP_REPAIR
enabled.
The function is called with skb being NULL and attempts to dereference it
on tcp_hdr(skb)->seq without a prior skb validation.
Fix this by checking if skb is NULL before dereferencing it.
The commentary is taken from bpf_skops_established(), which is also called
in the same flow. Unlike the function being patched,
bpf_skops_established() validates the skb before dereferencing it.
int main(void){
struct sockaddr_in sockaddr;
struct tcp_ao_add tcp_ao;
int sk;
int one = 1;
memset(&sockaddr,'\0',sizeof(sockaddr));
memset(&tcp_ao,'\0',sizeof(tcp_ao));
sk = socket(AF_INET, SOCK_STREAM, IPPROTO_TCP);
sockaddr.sin_family = AF_INET;
memcpy(tcp_ao.alg_name,"cmac(aes128)",12);
memcpy(tcp_ao.key,"ABCDEFGHABCDEFGH",16);
tcp_ao.keylen = 16;
memcpy(&tcp_ao.addr,&sockaddr,sizeof(sockaddr));
setsockopt(sk, IPPROTO_TCP, TCP_AO_ADD_KEY, &tcp_ao,
sizeof(tcp_ao));
setsockopt(sk, IPPROTO_TCP, TCP_REPAIR, &one, sizeof(one));
sockaddr.sin_family = AF_INET;
sockaddr.sin_port = htobe16(123);
inet_aton("127.0.0.1", &sockaddr.sin_addr);
connect(sk,(struct sockaddr *)&sockaddr,sizeof(sockaddr));
return 0;
}
$ gcc tcp-ao-nullptr.c -o tcp-ao-nullptr -Wall
$ unshare -Urn
BUG: kernel NULL pointer dereference, address: 00000000000000b6
PGD 1f648d067 P4D 1f648d067 PUD 1982e8067 PMD 0
Oops: Oops: 0000 [#1] SMP NOPTI
Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop
Reference Platform, BIOS 6.00 11/12/2020
RIP: 0010:tcp_ao_finish_connect (net/ipv4/tcp_ao.c:1182) |
| In the Linux kernel, the following vulnerability has been resolved:
block, bfq: fix possible uaf for 'bfqq->bic'
Our test report a uaf for 'bfqq->bic' in 5.10:
==================================================================
BUG: KASAN: use-after-free in bfq_select_queue+0x378/0xa30
CPU: 6 PID: 2318352 Comm: fsstress Kdump: loaded Not tainted 5.10.0-60.18.0.50.h602.kasan.eulerosv2r11.x86_64 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58-20220320_160524-szxrtosci10000 04/01/2014
Call Trace:
bfq_select_queue+0x378/0xa30
bfq_dispatch_request+0xe8/0x130
blk_mq_do_dispatch_sched+0x62/0xb0
__blk_mq_sched_dispatch_requests+0x215/0x2a0
blk_mq_sched_dispatch_requests+0x8f/0xd0
__blk_mq_run_hw_queue+0x98/0x180
__blk_mq_delay_run_hw_queue+0x22b/0x240
blk_mq_run_hw_queue+0xe3/0x190
blk_mq_sched_insert_requests+0x107/0x200
blk_mq_flush_plug_list+0x26e/0x3c0
blk_finish_plug+0x63/0x90
__iomap_dio_rw+0x7b5/0x910
iomap_dio_rw+0x36/0x80
ext4_dio_read_iter+0x146/0x190 [ext4]
ext4_file_read_iter+0x1e2/0x230 [ext4]
new_sync_read+0x29f/0x400
vfs_read+0x24e/0x2d0
ksys_read+0xd5/0x1b0
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x61/0xc6
Commit 3bc5e683c67d ("bfq: Split shared queues on move between cgroups")
changes that move process to a new cgroup will allocate a new bfqq to
use, however, the old bfqq and new bfqq can point to the same bic:
1) Initial state, two process with io in the same cgroup.
Process 1 Process 2
(BIC1) (BIC2)
| Λ | Λ
| | | |
V | V |
bfqq1 bfqq2
2) bfqq1 is merged to bfqq2.
Process 1 Process 2
(BIC1) (BIC2)
| |
\-------------\|
V
bfqq1 bfqq2(coop)
3) Process 1 exit, then issue new io(denoce IOA) from Process 2.
(BIC2)
| Λ
| |
V |
bfqq2(coop)
4) Before IOA is completed, move Process 2 to another cgroup and issue io.
Process 2
(BIC2)
Λ
|\--------------\
| V
bfqq2 bfqq3
Now that BIC2 points to bfqq3, while bfqq2 and bfqq3 both point to BIC2.
If all the requests are completed, and Process 2 exit, BIC2 will be
freed while there is no guarantee that bfqq2 will be freed before BIC2.
Fix the problem by clearing bfqq->bic while bfqq is detached from bic. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm: fix use-after-free on probe deferral
The bridge counter was never reset when tearing down the DRM device so
that stale pointers to deallocated structures would be accessed on the
next tear down (e.g. after a second late bind deferral).
Given enough bridges and a few probe deferrals this could currently also
lead to data beyond the bridge array being corrupted.
Patchwork: https://patchwork.freedesktop.org/patch/502665/ |
