| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ath10k: skip ath10k_halt during suspend for driver state RESTARTING
Double free crash is observed when FW recovery(caused by wmi
timeout/crash) is followed by immediate suspend event. The FW recovery
is triggered by ath10k_core_restart() which calls driver clean up via
ath10k_halt(). When the suspend event occurs between the FW recovery,
the restart worker thread is put into frozen state until suspend completes.
The suspend event triggers ath10k_stop() which again triggers ath10k_halt()
The double invocation of ath10k_halt() causes ath10k_htt_rx_free() to be
called twice(Note: ath10k_htt_rx_alloc was not called by restart worker
thread because of its frozen state), causing the crash.
To fix this, during the suspend flow, skip call to ath10k_halt() in
ath10k_stop() when the current driver state is ATH10K_STATE_RESTARTING.
Also, for driver state ATH10K_STATE_RESTARTING, call
ath10k_wait_for_suspend() in ath10k_stop(). This is because call to
ath10k_wait_for_suspend() is skipped later in
[ath10k_halt() > ath10k_core_stop()] for the driver state
ATH10K_STATE_RESTARTING.
The frozen restart worker thread will be cancelled during resume when the
device comes out of suspend.
Below is the crash stack for reference:
[ 428.469167] ------------[ cut here ]------------
[ 428.469180] kernel BUG at mm/slub.c:4150!
[ 428.469193] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
[ 428.469219] Workqueue: events_unbound async_run_entry_fn
[ 428.469230] RIP: 0010:kfree+0x319/0x31b
[ 428.469241] RSP: 0018:ffffa1fac015fc30 EFLAGS: 00010246
[ 428.469247] RAX: ffffedb10419d108 RBX: ffff8c05262b0000
[ 428.469252] RDX: ffff8c04a8c07000 RSI: 0000000000000000
[ 428.469256] RBP: ffffa1fac015fc78 R08: 0000000000000000
[ 428.469276] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 428.469285] Call Trace:
[ 428.469295] ? dma_free_attrs+0x5f/0x7d
[ 428.469320] ath10k_core_stop+0x5b/0x6f
[ 428.469336] ath10k_halt+0x126/0x177
[ 428.469352] ath10k_stop+0x41/0x7e
[ 428.469387] drv_stop+0x88/0x10e
[ 428.469410] __ieee80211_suspend+0x297/0x411
[ 428.469441] rdev_suspend+0x6e/0xd0
[ 428.469462] wiphy_suspend+0xb1/0x105
[ 428.469483] ? name_show+0x2d/0x2d
[ 428.469490] dpm_run_callback+0x8c/0x126
[ 428.469511] ? name_show+0x2d/0x2d
[ 428.469517] __device_suspend+0x2e7/0x41b
[ 428.469523] async_suspend+0x1f/0x93
[ 428.469529] async_run_entry_fn+0x3d/0xd1
[ 428.469535] process_one_work+0x1b1/0x329
[ 428.469541] worker_thread+0x213/0x372
[ 428.469547] kthread+0x150/0x15f
[ 428.469552] ? pr_cont_work+0x58/0x58
[ 428.469558] ? kthread_blkcg+0x31/0x31
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00288-QCARMSWPZ-1 |
| In the Linux kernel, the following vulnerability has been resolved:
fbdev: defio: fix the pagelist corruption
Easily hit the below list corruption:
==
list_add corruption. prev->next should be next (ffffffffc0ceb090), but
was ffffec604507edc8. (prev=ffffec604507edc8).
WARNING: CPU: 65 PID: 3959 at lib/list_debug.c:26
__list_add_valid+0x53/0x80
CPU: 65 PID: 3959 Comm: fbdev Tainted: G U
RIP: 0010:__list_add_valid+0x53/0x80
Call Trace:
<TASK>
fb_deferred_io_mkwrite+0xea/0x150
do_page_mkwrite+0x57/0xc0
do_wp_page+0x278/0x2f0
__handle_mm_fault+0xdc2/0x1590
handle_mm_fault+0xdd/0x2c0
do_user_addr_fault+0x1d3/0x650
exc_page_fault+0x77/0x180
? asm_exc_page_fault+0x8/0x30
asm_exc_page_fault+0x1e/0x30
RIP: 0033:0x7fd98fc8fad1
==
Figure out the race happens when one process is adding &page->lru into
the pagelist tail in fb_deferred_io_mkwrite(), another process is
re-initializing the same &page->lru in fb_deferred_io_fault(), which is
not protected by the lock.
This fix is to init all the page lists one time during initialization,
it not only fixes the list corruption, but also avoids INIT_LIST_HEAD()
redundantly.
V2: change "int i" to "unsigned int i" (Geert Uytterhoeven) |
| In the Linux kernel, the following vulnerability has been resolved:
rtw89: cfo: check mac_id to avoid out-of-bounds
Somehow, hardware reports incorrect mac_id and pollute memory. Check index
before we access the array.
UBSAN: array-index-out-of-bounds in rtw89/phy.c:2517:23
index 188 is out of range for type 's32 [64]'
CPU: 1 PID: 51550 Comm: irq/35-rtw89_pc Tainted: G OE
Call Trace:
<IRQ>
show_stack+0x52/0x58
dump_stack_lvl+0x4c/0x63
dump_stack+0x10/0x12
ubsan_epilogue+0x9/0x45
__ubsan_handle_out_of_bounds.cold+0x44/0x49
? __alloc_skb+0x92/0x1d0
rtw89_phy_cfo_parse+0x44/0x7f [rtw89_core]
rtw89_core_rx+0x261/0x871 [rtw89_core]
? __alloc_skb+0xee/0x1d0
rtw89_pci_napi_poll+0x3fa/0x4ea [rtw89_pci]
__napi_poll+0x33/0x1a0
net_rx_action+0x126/0x260
? __queue_work+0x217/0x4c0
__do_softirq+0xd9/0x315
? disable_irq_nosync+0x10/0x10
do_softirq.part.0+0x6d/0x90
</IRQ>
<TASK>
__local_bh_enable_ip+0x62/0x70
rtw89_pci_interrupt_threadfn+0x182/0x1a6 [rtw89_pci]
irq_thread_fn+0x28/0x60
irq_thread+0xc8/0x190
? irq_thread_fn+0x60/0x60
kthread+0x16b/0x190
? irq_thread_check_affinity+0xe0/0xe0
? set_kthread_struct+0x50/0x50
ret_from_fork+0x22/0x30
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
firmware: arm_scmi: Fix list protocols enumeration in the base protocol
While enumerating protocols implemented by the SCMI platform using
BASE_DISCOVER_LIST_PROTOCOLS, the number of returned protocols is
currently validated in an improper way since the check employs a sum
between unsigned integers that could overflow and cause the check itself
to be silently bypassed if the returned value 'loop_num_ret' is big
enough.
Fix the validation avoiding the addition. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: fix use-after-free in chanctx code
In ieee80211_vif_use_reserved_context(), when we have an
old context and the new context's replace_state is set to
IEEE80211_CHANCTX_REPLACE_NONE, we free the old context
in ieee80211_vif_use_reserved_reassign(). Therefore, we
cannot check the old_ctx anymore, so we should set it to
NULL after this point.
However, since the new_ctx replace state is clearly not
IEEE80211_CHANCTX_REPLACES_OTHER, we're not going to do
anything else in this function and can just return to
avoid accessing the freed old_ctx. |
| In the Linux kernel, the following vulnerability has been resolved:
dlm: fix plock invalid read
This patch fixes an invalid read showed by KASAN. A unlock will allocate a
"struct plock_op" and a followed send_op() will append it to a global
send_list data structure. In some cases a followed dev_read() moves it
to recv_list and dev_write() will cast it to "struct plock_xop" and access
fields which are only available in those structures. At this point an
invalid read happens by accessing those fields.
To fix this issue the "callback" field is moved to "struct plock_op" to
indicate that a cast to "plock_xop" is allowed and does the additional
"plock_xop" handling if set.
Example of the KASAN output which showed the invalid read:
[ 2064.296453] ==================================================================
[ 2064.304852] BUG: KASAN: slab-out-of-bounds in dev_write+0x52b/0x5a0 [dlm]
[ 2064.306491] Read of size 8 at addr ffff88800ef227d8 by task dlm_controld/7484
[ 2064.308168]
[ 2064.308575] CPU: 0 PID: 7484 Comm: dlm_controld Kdump: loaded Not tainted 5.14.0+ #9
[ 2064.310292] Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
[ 2064.311618] Call Trace:
[ 2064.312218] dump_stack_lvl+0x56/0x7b
[ 2064.313150] print_address_description.constprop.8+0x21/0x150
[ 2064.314578] ? dev_write+0x52b/0x5a0 [dlm]
[ 2064.315610] ? dev_write+0x52b/0x5a0 [dlm]
[ 2064.316595] kasan_report.cold.14+0x7f/0x11b
[ 2064.317674] ? dev_write+0x52b/0x5a0 [dlm]
[ 2064.318687] dev_write+0x52b/0x5a0 [dlm]
[ 2064.319629] ? dev_read+0x4a0/0x4a0 [dlm]
[ 2064.320713] ? bpf_lsm_kernfs_init_security+0x10/0x10
[ 2064.321926] vfs_write+0x17e/0x930
[ 2064.322769] ? __fget_light+0x1aa/0x220
[ 2064.323753] ksys_write+0xf1/0x1c0
[ 2064.324548] ? __ia32_sys_read+0xb0/0xb0
[ 2064.325464] do_syscall_64+0x3a/0x80
[ 2064.326387] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 2064.327606] RIP: 0033:0x7f807e4ba96f
[ 2064.328470] Code: 89 54 24 18 48 89 74 24 10 89 7c 24 08 e8 39 87 f8 ff 48 8b 54 24 18 48 8b 74 24 10 41 89 c0 8b 7c 24 08 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 31 44 89 c7 48 89 44 24 08 e8 7c 87 f8 ff 48
[ 2064.332902] RSP: 002b:00007ffd50cfe6e0 EFLAGS: 00000293 ORIG_RAX: 0000000000000001
[ 2064.334658] RAX: ffffffffffffffda RBX: 000055cc3886eb30 RCX: 00007f807e4ba96f
[ 2064.336275] RDX: 0000000000000040 RSI: 00007ffd50cfe7e0 RDI: 0000000000000010
[ 2064.337980] RBP: 00007ffd50cfe7e0 R08: 0000000000000000 R09: 0000000000000001
[ 2064.339560] R10: 000055cc3886eb30 R11: 0000000000000293 R12: 000055cc3886eb80
[ 2064.341237] R13: 000055cc3886eb00 R14: 000055cc3886f590 R15: 0000000000000001
[ 2064.342857]
[ 2064.343226] Allocated by task 12438:
[ 2064.344057] kasan_save_stack+0x1c/0x40
[ 2064.345079] __kasan_kmalloc+0x84/0xa0
[ 2064.345933] kmem_cache_alloc_trace+0x13b/0x220
[ 2064.346953] dlm_posix_unlock+0xec/0x720 [dlm]
[ 2064.348811] do_lock_file_wait.part.32+0xca/0x1d0
[ 2064.351070] fcntl_setlk+0x281/0xbc0
[ 2064.352879] do_fcntl+0x5e4/0xfe0
[ 2064.354657] __x64_sys_fcntl+0x11f/0x170
[ 2064.356550] do_syscall_64+0x3a/0x80
[ 2064.358259] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 2064.360745]
[ 2064.361511] Last potentially related work creation:
[ 2064.363957] kasan_save_stack+0x1c/0x40
[ 2064.365811] __kasan_record_aux_stack+0xaf/0xc0
[ 2064.368100] call_rcu+0x11b/0xf70
[ 2064.369785] dlm_process_incoming_buffer+0x47d/0xfd0 [dlm]
[ 2064.372404] receive_from_sock+0x290/0x770 [dlm]
[ 2064.374607] process_recv_sockets+0x32/0x40 [dlm]
[ 2064.377290] process_one_work+0x9a8/0x16e0
[ 2064.379357] worker_thread+0x87/0xbf0
[ 2064.381188] kthread+0x3ac/0x490
[ 2064.383460] ret_from_fork+0x22/0x30
[ 2064.385588]
[ 2064.386518] Second to last potentially related work creation:
[ 2064.389219] kasan_save_stack+0x1c/0x40
[ 2064.391043] __kasan_record_aux_stack+0xaf/0xc0
[ 2064.393303] call_rcu+0x11b/0xf70
[ 2064.394885] dlm_process_incoming_buffer+0x47d/0xfd0 [dlm]
[ 2064.397694] receive_from_sock+0x290/0x770
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
NFSD: Fix potential use-after-free in nfsd_file_put()
nfsd_file_put_noref() can free @nf, so don't dereference @nf
immediately upon return from nfsd_file_put_noref(). |
| In the Linux kernel, the following vulnerability has been resolved:
SUNRPC: Trap RDMA segment overflows
Prevent svc_rdma_build_writes() from walking off the end of a Write
chunk's segment array. Caught with KASAN.
The test that this fix replaces is invalid, and might have been left
over from an earlier prototype of the PCL work. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix use-after-free in ext4_rename_dir_prepare
We got issue as follows:
EXT4-fs (loop0): mounted filesystem without journal. Opts: ,errors=continue
ext4_get_first_dir_block: bh->b_data=0xffff88810bee6000 len=34478
ext4_get_first_dir_block: *parent_de=0xffff88810beee6ae bh->b_data=0xffff88810bee6000
ext4_rename_dir_prepare: [1] parent_de=0xffff88810beee6ae
==================================================================
BUG: KASAN: use-after-free in ext4_rename_dir_prepare+0x152/0x220
Read of size 4 at addr ffff88810beee6ae by task rep/1895
CPU: 13 PID: 1895 Comm: rep Not tainted 5.10.0+ #241
Call Trace:
dump_stack+0xbe/0xf9
print_address_description.constprop.0+0x1e/0x220
kasan_report.cold+0x37/0x7f
ext4_rename_dir_prepare+0x152/0x220
ext4_rename+0xf44/0x1ad0
ext4_rename2+0x11c/0x170
vfs_rename+0xa84/0x1440
do_renameat2+0x683/0x8f0
__x64_sys_renameat+0x53/0x60
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7f45a6fc41c9
RSP: 002b:00007ffc5a470218 EFLAGS: 00000246 ORIG_RAX: 0000000000000108
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f45a6fc41c9
RDX: 0000000000000005 RSI: 0000000020000180 RDI: 0000000000000005
RBP: 00007ffc5a470240 R08: 00007ffc5a470160 R09: 0000000020000080
R10: 00000000200001c0 R11: 0000000000000246 R12: 0000000000400bb0
R13: 00007ffc5a470320 R14: 0000000000000000 R15: 0000000000000000
The buggy address belongs to the page:
page:00000000440015ce refcount:0 mapcount:0 mapping:0000000000000000 index:0x1 pfn:0x10beee
flags: 0x200000000000000()
raw: 0200000000000000 ffffea00043ff4c8 ffffea0004325608 0000000000000000
raw: 0000000000000001 0000000000000000 00000000ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff88810beee580: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ffff88810beee600: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>ffff88810beee680: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
^
ffff88810beee700: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ffff88810beee780: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
==================================================================
Disabling lock debugging due to kernel taint
ext4_rename_dir_prepare: [2] parent_de->inode=3537895424
ext4_rename_dir_prepare: [3] dir=0xffff888124170140
ext4_rename_dir_prepare: [4] ino=2
ext4_rename_dir_prepare: ent->dir->i_ino=2 parent=-757071872
Reason is first directory entry which 'rec_len' is 34478, then will get illegal
parent entry. Now, we do not check directory entry after read directory block
in 'ext4_get_first_dir_block'.
To solve this issue, check directory entry in 'ext4_get_first_dir_block'.
[ Trigger an ext4_error() instead of just warning if the directory is
missing a '.' or '..' entry. Also make sure we return an error code
if the file system is corrupted. -TYT ] |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: avoid cycles in directory h-tree
A maliciously corrupted filesystem can contain cycles in the h-tree
stored inside a directory. That can easily lead to the kernel corrupting
tree nodes that were already verified under its hands while doing a node
split and consequently accessing unallocated memory. Fix the problem by
verifying traversed block numbers are unique. |
| In the Linux kernel, the following vulnerability has been resolved:
ip_gre: test csum_start instead of transport header
GRE with TUNNEL_CSUM will apply local checksum offload on
CHECKSUM_PARTIAL packets.
ipgre_xmit must validate csum_start after an optional skb_pull,
else lco_csum may trigger an overflow. The original check was
if (csum && skb_checksum_start(skb) < skb->data)
return -EINVAL;
This had false positives when skb_checksum_start is undefined:
when ip_summed is not CHECKSUM_PARTIAL. A discussed refinement
was straightforward
if (csum && skb->ip_summed == CHECKSUM_PARTIAL &&
skb_checksum_start(skb) < skb->data)
return -EINVAL;
But was eventually revised more thoroughly:
- restrict the check to the only branch where needed, in an
uncommon GRE path that uses header_ops and calls skb_pull.
- test skb_transport_header, which is set along with csum_start
in skb_partial_csum_set in the normal header_ops datapath.
Turns out skbs can arrive in this branch without the transport
header set, e.g., through BPF redirection.
Revise the check back to check csum_start directly, and only if
CHECKSUM_PARTIAL. Do leave the check in the updated location.
Check field regardless of whether TUNNEL_CSUM is configured. |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: fix tcp_mtup_probe_success vs wrong snd_cwnd
syzbot got a new report [1] finally pointing to a very old bug,
added in initial support for MTU probing.
tcp_mtu_probe() has checks about starting an MTU probe if
tcp_snd_cwnd(tp) >= 11.
But nothing prevents tcp_snd_cwnd(tp) to be reduced later
and before the MTU probe succeeds.
This bug would lead to potential zero-divides.
Debugging added in commit 40570375356c ("tcp: add accessors
to read/set tp->snd_cwnd") has paid off :)
While we are at it, address potential overflows in this code.
[1]
WARNING: CPU: 1 PID: 14132 at include/net/tcp.h:1219 tcp_mtup_probe_success+0x366/0x570 net/ipv4/tcp_input.c:2712
Modules linked in:
CPU: 1 PID: 14132 Comm: syz-executor.2 Not tainted 5.18.0-syzkaller-07857-gbabf0bb978e3 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:tcp_snd_cwnd_set include/net/tcp.h:1219 [inline]
RIP: 0010:tcp_mtup_probe_success+0x366/0x570 net/ipv4/tcp_input.c:2712
Code: 74 08 48 89 ef e8 da 80 17 f9 48 8b 45 00 65 48 ff 80 80 03 00 00 48 83 c4 30 5b 41 5c 41 5d 41 5e 41 5f 5d c3 e8 aa b0 c5 f8 <0f> 0b e9 16 fe ff ff 48 8b 4c 24 08 80 e1 07 38 c1 0f 8c c7 fc ff
RSP: 0018:ffffc900079e70f8 EFLAGS: 00010287
RAX: ffffffff88c0f7f6 RBX: ffff8880756e7a80 RCX: 0000000000040000
RDX: ffffc9000c6c4000 RSI: 0000000000031f9e RDI: 0000000000031f9f
RBP: 0000000000000000 R08: ffffffff88c0f606 R09: ffffc900079e7520
R10: ffffed101011226d R11: 1ffff1101011226c R12: 1ffff1100eadcf50
R13: ffff8880756e72c0 R14: 1ffff1100eadcf89 R15: dffffc0000000000
FS: 00007f643236e700(0000) GS:ffff8880b9b00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f1ab3f1e2a0 CR3: 0000000064fe7000 CR4: 00000000003506e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
tcp_clean_rtx_queue+0x223a/0x2da0 net/ipv4/tcp_input.c:3356
tcp_ack+0x1962/0x3c90 net/ipv4/tcp_input.c:3861
tcp_rcv_established+0x7c8/0x1ac0 net/ipv4/tcp_input.c:5973
tcp_v6_do_rcv+0x57b/0x1210 net/ipv6/tcp_ipv6.c:1476
sk_backlog_rcv include/net/sock.h:1061 [inline]
__release_sock+0x1d8/0x4c0 net/core/sock.c:2849
release_sock+0x5d/0x1c0 net/core/sock.c:3404
sk_stream_wait_memory+0x700/0xdc0 net/core/stream.c:145
tcp_sendmsg_locked+0x111d/0x3fc0 net/ipv4/tcp.c:1410
tcp_sendmsg+0x2c/0x40 net/ipv4/tcp.c:1448
sock_sendmsg_nosec net/socket.c:714 [inline]
sock_sendmsg net/socket.c:734 [inline]
__sys_sendto+0x439/0x5c0 net/socket.c:2119
__do_sys_sendto net/socket.c:2131 [inline]
__se_sys_sendto net/socket.c:2127 [inline]
__x64_sys_sendto+0xda/0xf0 net/socket.c:2127
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x2b/0x70 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
RIP: 0033:0x7f6431289109
Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f643236e168 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 00007f643139c100 RCX: 00007f6431289109
RDX: 00000000d0d0c2ac RSI: 0000000020000080 RDI: 000000000000000a
RBP: 00007f64312e308d R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000246 R12: 0000000000000000
R13: 00007fff372533af R14: 00007f643236e300 R15: 0000000000022000 |
| In the Linux kernel, the following vulnerability has been resolved:
mt76: fix use-after-free by removing a non-RCU wcid pointer
Fixes an issue caught by KASAN about use-after-free in mt76_txq_schedule
by protecting mtxq->wcid with rcu_lock between mt76_txq_schedule and
sta_info_[alloc, free].
[18853.876689] ==================================================================
[18853.876751] BUG: KASAN: use-after-free in mt76_txq_schedule+0x204/0xaf8 [mt76]
[18853.876773] Read of size 8 at addr ffffffaf989a2138 by task mt76-tx phy0/883
[18853.876786]
[18853.876810] CPU: 5 PID: 883 Comm: mt76-tx phy0 Not tainted 5.10.100-fix-510-56778d365941-kasan #5 0b01fbbcf41a530f52043508fec2e31a4215
[18853.876840] Call trace:
[18853.876861] dump_backtrace+0x0/0x3ec
[18853.876878] show_stack+0x20/0x2c
[18853.876899] dump_stack+0x11c/0x1ac
[18853.876918] print_address_description+0x74/0x514
[18853.876934] kasan_report+0x134/0x174
[18853.876948] __asan_report_load8_noabort+0x44/0x50
[18853.876976] mt76_txq_schedule+0x204/0xaf8 [mt76 074e03e4640e97fe7405ee1fab547b81c4fa45d2]
[18853.877002] mt76_txq_schedule_all+0x2c/0x48 [mt76 074e03e4640e97fe7405ee1fab547b81c4fa45d2]
[18853.877030] mt7921_tx_worker+0xa0/0x1cc [mt7921_common f0875ebac9d7b4754e1010549e7db50fbd90a047]
[18853.877054] __mt76_worker_fn+0x190/0x22c [mt76 074e03e4640e97fe7405ee1fab547b81c4fa45d2]
[18853.877071] kthread+0x2f8/0x3b8
[18853.877087] ret_from_fork+0x10/0x30
[18853.877098]
[18853.877112] Allocated by task 941:
[18853.877131] kasan_save_stack+0x38/0x68
[18853.877147] __kasan_kmalloc+0xd4/0xfc
[18853.877163] kasan_kmalloc+0x10/0x1c
[18853.877177] __kmalloc+0x264/0x3c4
[18853.877294] sta_info_alloc+0x460/0xf88 [mac80211]
[18853.877410] ieee80211_prep_connection+0x204/0x1ee0 [mac80211]
[18853.877523] ieee80211_mgd_auth+0x6c4/0xa4c [mac80211]
[18853.877635] ieee80211_auth+0x20/0x2c [mac80211]
[18853.877733] rdev_auth+0x7c/0x438 [cfg80211]
[18853.877826] cfg80211_mlme_auth+0x26c/0x390 [cfg80211]
[18853.877919] nl80211_authenticate+0x6d4/0x904 [cfg80211]
[18853.877938] genl_rcv_msg+0x748/0x93c
[18853.877954] netlink_rcv_skb+0x160/0x2a8
[18853.877969] genl_rcv+0x3c/0x54
[18853.877985] netlink_unicast_kernel+0x104/0x1ec
[18853.877999] netlink_unicast+0x178/0x268
[18853.878015] netlink_sendmsg+0x3cc/0x5f0
[18853.878030] sock_sendmsg+0xb4/0xd8
[18853.878043] ____sys_sendmsg+0x2f8/0x53c
[18853.878058] ___sys_sendmsg+0xe8/0x150
[18853.878071] __sys_sendmsg+0xc4/0x1f4
[18853.878087] __arm64_compat_sys_sendmsg+0x88/0x9c
[18853.878101] el0_svc_common+0x1b4/0x390
[18853.878115] do_el0_svc_compat+0x8c/0xdc
[18853.878131] el0_svc_compat+0x10/0x1c
[18853.878146] el0_sync_compat_handler+0xa8/0xcc
[18853.878161] el0_sync_compat+0x188/0x1c0
[18853.878171]
[18853.878183] Freed by task 10927:
[18853.878200] kasan_save_stack+0x38/0x68
[18853.878215] kasan_set_track+0x28/0x3c
[18853.878228] kasan_set_free_info+0x24/0x48
[18853.878244] __kasan_slab_free+0x11c/0x154
[18853.878259] kasan_slab_free+0x14/0x24
[18853.878273] slab_free_freelist_hook+0xac/0x1b0
[18853.878287] kfree+0x104/0x390
[18853.878402] sta_info_free+0x198/0x210 [mac80211]
[18853.878515] __sta_info_destroy_part2+0x230/0x2d4 [mac80211]
[18853.878628] __sta_info_flush+0x300/0x37c [mac80211]
[18853.878740] ieee80211_set_disassoc+0x2cc/0xa7c [mac80211]
[18853.878851] ieee80211_mgd_deauth+0x4a4/0x10a0 [mac80211]
[18853.878962] ieee80211_deauth+0x20/0x2c [mac80211]
[18853.879057] rdev_deauth+0x7c/0x438 [cfg80211]
[18853.879150] cfg80211_mlme_deauth+0x274/0x414 [cfg80211]
[18853.879243] cfg80211_mlme_down+0xe4/0x118 [cfg80211]
[18853.879335] cfg80211_disconnect+0x218/0x2d8 [cfg80211]
[18853.879427] __cfg80211_leave+0x17c/0x240 [cfg80211]
[18853.879519] cfg80211_leave+0x3c/0x58 [cfg80211]
[18853.879611] wiphy_suspend+0xdc/0x200 [cfg80211]
[18853.879628] dpm_run_callback+0x58/0x408
[18853.879642] __device_suspend+0x4cc/0x864
[18853.879658] async_suspend+0x34/0xf4
[18
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: add accessors to read/set tp->snd_cwnd
We had various bugs over the years with code
breaking the assumption that tp->snd_cwnd is greater
than zero.
Lately, syzbot reported the WARN_ON_ONCE(!tp->prior_cwnd) added
in commit 8b8a321ff72c ("tcp: fix zero cwnd in tcp_cwnd_reduction")
can trigger, and without a repro we would have to spend
considerable time finding the bug.
Instead of complaining too late, we want to catch where
and when tp->snd_cwnd is set to an illegal value. |
| In the Linux kernel, the following vulnerability has been resolved:
xprtrdma: treat all calls not a bcall when bc_serv is NULL
When a rdma server returns a fault format reply, nfs v3 client may
treats it as a bcall when bc service is not exist.
The debug message at rpcrdma_bc_receive_call are,
[56579.837169] RPC: rpcrdma_bc_receive_call: callback XID
00000001, length=20
[56579.837174] RPC: rpcrdma_bc_receive_call: 00 00 00 01 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 04
After that, rpcrdma_bc_receive_call will meets NULL pointer as,
[ 226.057890] BUG: unable to handle kernel NULL pointer dereference at
00000000000000c8
...
[ 226.058704] RIP: 0010:_raw_spin_lock+0xc/0x20
...
[ 226.059732] Call Trace:
[ 226.059878] rpcrdma_bc_receive_call+0x138/0x327 [rpcrdma]
[ 226.060011] __ib_process_cq+0x89/0x170 [ib_core]
[ 226.060092] ib_cq_poll_work+0x26/0x80 [ib_core]
[ 226.060257] process_one_work+0x1a7/0x360
[ 226.060367] ? create_worker+0x1a0/0x1a0
[ 226.060440] worker_thread+0x30/0x390
[ 226.060500] ? create_worker+0x1a0/0x1a0
[ 226.060574] kthread+0x116/0x130
[ 226.060661] ? kthread_flush_work_fn+0x10/0x10
[ 226.060724] ret_from_fork+0x35/0x40
... |
| In the Linux kernel, the following vulnerability has been resolved:
tpm: fix reference counting for struct tpm_chip
The following sequence of operations results in a refcount warning:
1. Open device /dev/tpmrm.
2. Remove module tpm_tis_spi.
3. Write a TPM command to the file descriptor opened at step 1.
------------[ cut here ]------------
WARNING: CPU: 3 PID: 1161 at lib/refcount.c:25 kobject_get+0xa0/0xa4
refcount_t: addition on 0; use-after-free.
Modules linked in: tpm_tis_spi tpm_tis_core tpm mdio_bcm_unimac brcmfmac
sha256_generic libsha256 sha256_arm hci_uart btbcm bluetooth cfg80211 vc4
brcmutil ecdh_generic ecc snd_soc_core crc32_arm_ce libaes
raspberrypi_hwmon ac97_bus snd_pcm_dmaengine bcm2711_thermal snd_pcm
snd_timer genet snd phy_generic soundcore [last unloaded: spi_bcm2835]
CPU: 3 PID: 1161 Comm: hold_open Not tainted 5.10.0ls-main-dirty #2
Hardware name: BCM2711
[<c0410c3c>] (unwind_backtrace) from [<c040b580>] (show_stack+0x10/0x14)
[<c040b580>] (show_stack) from [<c1092174>] (dump_stack+0xc4/0xd8)
[<c1092174>] (dump_stack) from [<c0445a30>] (__warn+0x104/0x108)
[<c0445a30>] (__warn) from [<c0445aa8>] (warn_slowpath_fmt+0x74/0xb8)
[<c0445aa8>] (warn_slowpath_fmt) from [<c08435d0>] (kobject_get+0xa0/0xa4)
[<c08435d0>] (kobject_get) from [<bf0a715c>] (tpm_try_get_ops+0x14/0x54 [tpm])
[<bf0a715c>] (tpm_try_get_ops [tpm]) from [<bf0a7d6c>] (tpm_common_write+0x38/0x60 [tpm])
[<bf0a7d6c>] (tpm_common_write [tpm]) from [<c05a7ac0>] (vfs_write+0xc4/0x3c0)
[<c05a7ac0>] (vfs_write) from [<c05a7ee4>] (ksys_write+0x58/0xcc)
[<c05a7ee4>] (ksys_write) from [<c04001a0>] (ret_fast_syscall+0x0/0x4c)
Exception stack(0xc226bfa8 to 0xc226bff0)
bfa0: 00000000 000105b4 00000003 beafe664 00000014 00000000
bfc0: 00000000 000105b4 000103f8 00000004 00000000 00000000 b6f9c000 beafe684
bfe0: 0000006c beafe648 0001056c b6eb6944
---[ end trace d4b8409def9b8b1f ]---
The reason for this warning is the attempt to get the chip->dev reference
in tpm_common_write() although the reference counter is already zero.
Since commit 8979b02aaf1d ("tpm: Fix reference count to main device") the
extra reference used to prevent a premature zero counter is never taken,
because the required TPM_CHIP_FLAG_TPM2 flag is never set.
Fix this by moving the TPM 2 character device handling from
tpm_chip_alloc() to tpm_add_char_device() which is called at a later point
in time when the flag has been set in case of TPM2.
Commit fdc915f7f719 ("tpm: expose spaces via a device link /dev/tpmrm<n>")
already introduced function tpm_devs_release() to release the extra
reference but did not implement the required put on chip->devs that results
in the call of this function.
Fix this by putting chip->devs in tpm_chip_unregister().
Finally move the new implementation for the TPM 2 handling into a new
function to avoid multiple checks for the TPM_CHIP_FLAG_TPM2 flag in the
good case and error cases. |
| In the Linux kernel, the following vulnerability has been resolved:
exec: Force single empty string when argv is empty
Quoting[1] Ariadne Conill:
"In several other operating systems, it is a hard requirement that the
second argument to execve(2) be the name of a program, thus prohibiting
a scenario where argc < 1. POSIX 2017 also recommends this behaviour,
but it is not an explicit requirement[2]:
The argument arg0 should point to a filename string that is
associated with the process being started by one of the exec
functions.
...
Interestingly, Michael Kerrisk opened an issue about this in 2008[3],
but there was no consensus to support fixing this issue then.
Hopefully now that CVE-2021-4034 shows practical exploitative use[4]
of this bug in a shellcode, we can reconsider.
This issue is being tracked in the KSPP issue tracker[5]."
While the initial code searches[6][7] turned up what appeared to be
mostly corner case tests, trying to that just reject argv == NULL
(or an immediately terminated pointer list) quickly started tripping[8]
existing userspace programs.
The next best approach is forcing a single empty string into argv and
adjusting argc to match. The number of programs depending on argc == 0
seems a smaller set than those calling execve with a NULL argv.
Account for the additional stack space in bprm_stack_limits(). Inject an
empty string when argc == 0 (and set argc = 1). Warn about the case so
userspace has some notice about the change:
process './argc0' launched './argc0' with NULL argv: empty string added
Additionally WARN() and reject NULL argv usage for kernel threads.
[1] https://lore.kernel.org/lkml/[email protected]/
[2] https://pubs.opengroup.org/onlinepubs/9699919799/functions/exec.html
[3] https://bugzilla.kernel.org/show_bug.cgi?id=8408
[4] https://www.qualys.com/2022/01/25/cve-2021-4034/pwnkit.txt
[5] https://github.com/KSPP/linux/issues/176
[6] https://codesearch.debian.net/search?q=execve%5C+*%5C%28%5B%5E%2C%5D%2B%2C+*NULL&literal=0
[7] https://codesearch.debian.net/search?q=execlp%3F%5Cs*%5C%28%5B%5E%2C%5D%2B%2C%5Cs*NULL&literal=0
[8] https://lore.kernel.org/lkml/20220131144352.GE16385@xsang-OptiPlex-9020/ |
| In the Linux kernel, the following vulnerability has been resolved:
ath11k: free peer for station when disconnect from AP for QCA6390/WCN6855
Commit b4a0f54156ac ("ath11k: move peer delete after vdev stop of station
for QCA6390 and WCN6855") is to fix firmware crash by changing the WMI
command sequence, but actually skip all the peer delete operation, then
it lead commit 58595c9874c6 ("ath11k: Fixing dangling pointer issue upon
peer delete failure") not take effect, and then happened a use-after-free
warning from KASAN. because the peer->sta is not set to NULL and then used
later.
Change to only skip the WMI_PEER_DELETE_CMDID for QCA6390/WCN6855.
log of user-after-free:
[ 534.888665] BUG: KASAN: use-after-free in ath11k_dp_rx_update_peer_stats+0x912/0xc10 [ath11k]
[ 534.888696] Read of size 8 at addr ffff8881396bb1b8 by task rtcwake/2860
[ 534.888705] CPU: 4 PID: 2860 Comm: rtcwake Kdump: loaded Tainted: G W 5.15.0-wt-ath+ #523
[ 534.888712] Hardware name: Intel(R) Client Systems NUC8i7HVK/NUC8i7HVB, BIOS HNKBLi70.86A.0067.2021.0528.1339 05/28/2021
[ 534.888716] Call Trace:
[ 534.888720] <IRQ>
[ 534.888726] dump_stack_lvl+0x57/0x7d
[ 534.888736] print_address_description.constprop.0+0x1f/0x170
[ 534.888745] ? ath11k_dp_rx_update_peer_stats+0x912/0xc10 [ath11k]
[ 534.888771] kasan_report.cold+0x83/0xdf
[ 534.888783] ? ath11k_dp_rx_update_peer_stats+0x912/0xc10 [ath11k]
[ 534.888810] ath11k_dp_rx_update_peer_stats+0x912/0xc10 [ath11k]
[ 534.888840] ath11k_dp_rx_process_mon_status+0x529/0xa70 [ath11k]
[ 534.888874] ? ath11k_dp_rx_mon_status_bufs_replenish+0x3f0/0x3f0 [ath11k]
[ 534.888897] ? check_prev_add+0x20f0/0x20f0
[ 534.888922] ? __lock_acquire+0xb72/0x1870
[ 534.888937] ? find_held_lock+0x33/0x110
[ 534.888954] ath11k_dp_rx_process_mon_rings+0x297/0x520 [ath11k]
[ 534.888981] ? rcu_read_unlock+0x40/0x40
[ 534.888990] ? ath11k_dp_rx_pdev_alloc+0xd90/0xd90 [ath11k]
[ 534.889026] ath11k_dp_service_mon_ring+0x67/0xe0 [ath11k]
[ 534.889053] ? ath11k_dp_rx_process_mon_rings+0x520/0x520 [ath11k]
[ 534.889075] call_timer_fn+0x167/0x4a0
[ 534.889084] ? add_timer_on+0x3b0/0x3b0
[ 534.889103] ? lockdep_hardirqs_on_prepare.part.0+0x18c/0x370
[ 534.889117] __run_timers.part.0+0x539/0x8b0
[ 534.889123] ? ath11k_dp_rx_process_mon_rings+0x520/0x520 [ath11k]
[ 534.889157] ? call_timer_fn+0x4a0/0x4a0
[ 534.889164] ? mark_lock_irq+0x1c30/0x1c30
[ 534.889173] ? clockevents_program_event+0xdd/0x280
[ 534.889189] ? mark_held_locks+0xa5/0xe0
[ 534.889203] run_timer_softirq+0x97/0x180
[ 534.889213] __do_softirq+0x276/0x86a
[ 534.889230] __irq_exit_rcu+0x11c/0x180
[ 534.889238] irq_exit_rcu+0x5/0x20
[ 534.889244] sysvec_apic_timer_interrupt+0x8e/0xc0
[ 534.889251] </IRQ>
[ 534.889254] <TASK>
[ 534.889259] asm_sysvec_apic_timer_interrupt+0x12/0x20
[ 534.889265] RIP: 0010:_raw_spin_unlock_irqrestore+0x38/0x70
[ 534.889271] Code: 74 24 10 e8 ea c2 bf fd 48 89 ef e8 12 53 c0 fd 81 e3 00 02 00 00 75 25 9c 58 f6 c4 02 75 2d 48 85 db 74 01 fb bf 01 00 00 00 <e8> 13 a7 b5 fd 65 8b 05 cc d9 9c 5e 85 c0 74 0a 5b 5d c3 e8 a0 ee
[ 534.889276] RSP: 0018:ffffc90002e5f880 EFLAGS: 00000206
[ 534.889284] RAX: 0000000000000006 RBX: 0000000000000200 RCX: ffffffff9f256f10
[ 534.889289] RDX: 0000000000000000 RSI: ffffffffa1c6e420 RDI: 0000000000000001
[ 534.889293] RBP: ffff8881095e6200 R08: 0000000000000001 R09: ffffffffa40d2b8f
[ 534.889298] R10: fffffbfff481a571 R11: 0000000000000001 R12: ffff8881095e6e68
[ 534.889302] R13: ffffc90002e5f908 R14: 0000000000000246 R15: 0000000000000000
[ 534.889316] ? mark_lock+0xd0/0x14a0
[ 534.889332] klist_next+0x1d4/0x450
[ 534.889340] ? dpm_wait_for_subordinate+0x2d0/0x2d0
[ 534.889350] device_for_each_child+0xa8/0x140
[ 534.889360] ? device_remove_class_symlinks+0x1b0/0x1b0
[ 534.889370] ? __lock_release+0x4bd/0x9f0
[ 534.889378] ? dpm_suspend+0x26b/0x3f0
[ 534.889390] dpm_wait_for_subordinate+
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
xsk: Fix race at socket teardown
Fix a race in the xsk socket teardown code that can lead to a NULL pointer
dereference splat. The current xsk unbind code in xsk_unbind_dev() starts by
setting xs->state to XSK_UNBOUND, sets xs->dev to NULL and then waits for any
NAPI processing to terminate using synchronize_net(). After that, the release
code starts to tear down the socket state and free allocated memory.
BUG: kernel NULL pointer dereference, address: 00000000000000c0
PGD 8000000932469067 P4D 8000000932469067 PUD 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 25 PID: 69132 Comm: grpcpp_sync_ser Tainted: G I 5.16.0+ #2
Hardware name: Dell Inc. PowerEdge R730/0599V5, BIOS 1.2.10 03/09/2015
RIP: 0010:__xsk_sendmsg+0x2c/0x690
[...]
RSP: 0018:ffffa2348bd13d50 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000040 RCX: ffff8d5fc632d258
RDX: 0000000000400000 RSI: ffffa2348bd13e10 RDI: ffff8d5fc5489800
RBP: ffffa2348bd13db0 R08: 0000000000000000 R09: 00007ffffffff000
R10: 0000000000000000 R11: 0000000000000000 R12: ffff8d5fc5489800
R13: ffff8d5fcb0f5140 R14: ffff8d5fcb0f5140 R15: 0000000000000000
FS: 00007f991cff9400(0000) GS:ffff8d6f1f700000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000000000c0 CR3: 0000000114888005 CR4: 00000000001706e0
Call Trace:
<TASK>
? aa_sk_perm+0x43/0x1b0
xsk_sendmsg+0xf0/0x110
sock_sendmsg+0x65/0x70
__sys_sendto+0x113/0x190
? debug_smp_processor_id+0x17/0x20
? fpregs_assert_state_consistent+0x23/0x50
? exit_to_user_mode_prepare+0xa5/0x1d0
__x64_sys_sendto+0x29/0x30
do_syscall_64+0x3b/0xc0
entry_SYSCALL_64_after_hwframe+0x44/0xae
There are two problems with the current code. First, setting xs->dev to NULL
before waiting for all users to stop using the socket is not correct. The
entry to the data plane functions xsk_poll(), xsk_sendmsg(), and xsk_recvmsg()
are all guarded by a test that xs->state is in the state XSK_BOUND and if not,
it returns right away. But one process might have passed this test but still
have not gotten to the point in which it uses xs->dev in the code. In this
interim, a second process executing xsk_unbind_dev() might have set xs->dev to
NULL which will lead to a crash for the first process. The solution here is
just to get rid of this NULL assignment since it is not used anymore. Before
commit 42fddcc7c64b ("xsk: use state member for socket synchronization"),
xs->dev was the gatekeeper to admit processes into the data plane functions,
but it was replaced with the state variable xs->state in the aforementioned
commit.
The second problem is that synchronize_net() does not wait for any process in
xsk_poll(), xsk_sendmsg(), or xsk_recvmsg() to complete, which means that the
state they rely on might be cleaned up prematurely. This can happen when the
notifier gets called (at driver unload for example) as it uses xsk_unbind_dev().
Solve this by extending the RCU critical region from just the ndo_xsk_wakeup
to the whole functions mentioned above, so that both the test of xs->state ==
XSK_BOUND and the last use of any member of xs is covered by the RCU critical
section. This will guarantee that when synchronize_net() completes, there will
be no processes left executing xsk_poll(), xsk_sendmsg(), or xsk_recvmsg() and
state can be cleaned up safely. Note that we need to drop the RCU lock for the
skb xmit path as it uses functions that might sleep. Due to this, we have to
retest the xs->state after we grab the mutex that protects the skb xmit code
from, among a number of things, an xsk_unbind_dev() being executed from the
notifier at the same time. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Fix crash during module load unload test
During purex packet handling the driver was incorrectly freeing a
pre-allocated structure. Fix this by skipping that entry.
System crashed with the following stack during a module unload test.
Call Trace:
sbitmap_init_node+0x7f/0x1e0
sbitmap_queue_init_node+0x24/0x150
blk_mq_init_bitmaps+0x3d/0xa0
blk_mq_init_tags+0x68/0x90
blk_mq_alloc_map_and_rqs+0x44/0x120
blk_mq_alloc_set_map_and_rqs+0x63/0x150
blk_mq_alloc_tag_set+0x11b/0x230
scsi_add_host_with_dma.cold+0x3f/0x245
qla2x00_probe_one+0xd5a/0x1b80 [qla2xxx]
Call Trace with slub_debug and debug kernel:
kasan_report_invalid_free+0x50/0x80
__kasan_slab_free+0x137/0x150
slab_free_freelist_hook+0xc6/0x190
kfree+0xe8/0x2e0
qla2x00_free_device+0x3bb/0x5d0 [qla2xxx]
qla2x00_remove_one+0x668/0xcf0 [qla2xxx] |
