| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
binfmt_misc: reject a flag character as the field delimiter
The registration string starts with a user chosen delimiter that
separates the individual fields. So that the field parsers terminate
even on a truncated string create_entry() pads the buffer with that
same delimiter:
memset(buf + count, del, 8);
Most fields are scanned for the delimiter with strchr()/scanarg() and
happily stop on the padding. The flags field is different: instead of
scanning for the delimiter check_special_flags() consumes the flag
characters 'P', 'O', 'C' and 'F' and stops at the first byte that is
none of them, relying on the trailing delimiter to end the scan.
If the delimiter is itself a flag character the padding no longer acts
as a terminator. The scan swallows all eight padding bytes and keeps
reading past the end of the allocation until it hits a byte that is
not a flag character. For example registering
PaPEPPxPPiP
with 'P' as the delimiter (name "a", type extension, magic "x",
interpreter "i", empty flags) leaves the flag scan running off the end
of the buffer. The registration is rejected in the end because the
parser does not stop exactly at buf + count, but only after the out of
bounds read has already happened. With an unlucky allocation layout the
scan can walk into an unmapped page; under KASAN it is reported as a
slab out of bounds read. binfmt_misc mounts are available to
unprivileged users in a user namespace so the read is reachable without
privileges.
Reject a delimiter that is one of the flag characters up front. Such a
registration was always rejected anyway, only after the out of bounds
read, so no valid registration string changes meaning. |
| In the Linux kernel, the following vulnerability has been resolved:
vxlan: use pskb_network_may_pull() in route_shortcircuit()
route_shortcircuit() currently calls pskb_may_pull(skb, sizeof(struct iphdr))
(or ipv6hdr), which checks if bytes are available starting from skb->data.
However, in vxlan_xmit(), skb->data points to the MAC header, so
skb_network_offset(skb) is ETH_HLEN (14 bytes). Using pskb_may_pull(skb, 20)
only checks 20 bytes from skb->data (which is 14 bytes MAC header + 6 bytes of
IP header), leaving the rest of the IP header potentially un-pulled in non-linear
frags. Subsequent dereferences of ip_hdr(skb)->daddr can read beyond the pulled
linear buffer length.
Fix this by using pskb_network_may_pull(), which adds skb_network_offset(skb) to
the length check to ensure the full network header is present in the linear buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
ublk: reset kernel-owned dev_info fields in ublk_ctrl_add_dev()
ublk_ctrl_add_dev() memcpy()s the userspace ublksrv_ctrl_dev_info into
ub->dev_info and then fixes up the fields the driver owns, but misses
->state and ->ublksrv_pid.
A device added with ->state = UBLK_S_DEV_LIVE passes the
"->state != UBLK_S_DEV_DEAD" test that ublk_stop_dev_unlocked() uses as its
proxy for "a disk is attached", while ->ub_disk is still NULL, so DEL_DEV
right after ADD_DEV oopses in del_gendisk(). UBLK_S_DEV_QUIESCED plus
UBLK_F_USER_RECOVERY dies one step earlier, in ublk_force_abort_dev(). A
poisoned ->state also gets START_USER_RECOVERY and the char device
read/write path onto a device that was never started, and wedges START_DEV
at -EEXIST. A poisoned ->ublksrv_pid just makes GET_DEV_INFO report an
unrelated task as the ublk server.
Reset both after the memcpy(), as ublk_detach_disk() does. Userspace only
ever reads these back, so correcting them silently breaks nothing.
ADD_DEV has copied ->state in unsanitized since ublk was merged, but back
then it was harmless: the gendisk was allocated during ADD_DEV, and both
teardown and the START_DEV -EEXIST check keyed off disk_live() rather than
->state. The oops became reachable once the disk allocation moved to
START_DEV and those checks switched to ->state. |
| In Modem, there is a possible out of bounds read due to a missing bounds check. This could lead to remote denial of service, if a UE has connected to a rogue base station controlled by the attacker, with no additional execution privileges needed. User interaction is not needed for exploitation. Patch ID: MOLY00741071; Issue ID: MSV-7620. |
| In display, there is a possible information disclosure due to a missing bounds check. This could lead to local information disclosure if a malicious actor has already obtained the System privilege. User interaction is not needed for exploitation. Patch ID: ALPS11004276; Issue ID: MSV-7757. |
| In display, there is a possible information disclosure due to an integer overflow. This could lead to local information disclosure if a malicious actor has already obtained the System privilege. User interaction is not needed for exploitation. Patch ID: ALPS11004274; Issue ID: MSV-7749. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote attacker to cause a denial of service due to an out-of-bounds read. |
| In the Linux kernel, the following vulnerability has been resolved:
keys: fix out-of-bounds read in keyring_get_key_chunk()
For description-level chunks keyring_get_key_chunk() advances the read
pointer by level * sizeof(long) past the inline prefix but only
bounds-checks the prefix, so a long enough key description is read past
its kmemdup(desc, desc_len + 1) allocation. Compute the full byte
offset and bounds-check the description against it before reading.
The walk only reaches a description-level chunk when two keys collide
through the hash, x, type and domain_tag chunks, so this is reached from
an unprivileged add_key(2) with a crafted pair of same-type keys whose
index hashes collide; KASAN reports a slab-out-of-bounds read. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote authenticated attacker to obtain sensitive information or cause a denial of service due to an out-of-bounds read. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (nct6775-core) Fix number of temperature registers for NCT6116
Unlike NCT6106, NCT6116 only has three temperature registers, and with
it only three temperature source and temperature source configuration
registers. The register addresses match those of NCT6106 and can be
re-used.
The code used a separate array to list the temperature source registers
for NCT6116, but used the size of the NCT6106 register array to set
the number of registers. The NCT6106 register array provides six addresses,
while the temperature source register array for NCT6116 only provides three
addresses. This causes a KASAN report.
BUG: KASAN: global-out-of-bounds in nct6775_probe+0x936/0x46f0 [nct6775]
Read of size 2 at addr ffffffffc19561a6 by task modprobe/954
...
Call Trace:
dump_stack+0x7d/0xa7
print_address_description.constprop.0+0x1c/0x220
? __kasan_kmalloc.constprop.0+0xc9/0xd0
? __kmalloc_node_track_caller+0x194/0x5b0
? nct6775_probe+0x936/0x46f0 [nct6775]
? nct6775_probe+0x936/0x46f0 [nct6775]
...
Fix the problem by hard-coding the number of temperature and temperature
configuration registers to three for NCT6116. Drop the unnecessary
NCT6116_REG_TEMP_SOURCE array and re-use NCT6106_REG_TEMP_SOURCE. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (nct6775-core) Prevent access to unsupported weight registers
Sashiko reports:
During initialization of the nct6116 chip, the driver sets data->pwm_num
to 5. However, it assigns several NCT6106 register arrays (such as
NCT6106_REG_WEIGHT_DUTY_STEP, NCT6106_REG_WEIGHT_TEMP_SEL, and
NCT6106_REG_WEIGHT_TEMP_*) to data->REG_PWM and data->REG_WEIGHT_TEMP.
These arrays only contain 3 elements.
In nct6775_update_pwm(), the driver iterates up to data->pwm_num. If
data->has_pwm has bits 3 or 4 set (which is structurally possible for
nct6116), the loop attempts to read elements at index 3 and 4 from these
3-element arrays. This results in a global out-of-bounds read, which can
be caught by KASAN.
Furthermore, the driver uses these garbage out-of-bounds values as
hardware register addresses for subsequent read and write operations. This
leads to invalid hardware register access, potentially causing hardware
misconfiguration or system crashes.
The underlying problem is that the chip does support up to five fan
control channels, but only the first three support weight control.
Fix the problem by extending the affected weight register arrays with
zeroed fields. The driver uses zeroed register addresses to determine
if a register is supported or not, and skips accesses for unsupported
registers. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: HIDP: reject frames without a transaction header
hidp_recv_ctrl_frame() and hidp_recv_intr_frame() read skb->data[0]
before checking that the L2CAP SDU contains a transaction header. A
connected HIDP peer can send an empty basic-mode SDU and make both paths
use an uninitialized byte from skb tailroom.
KMSAN reports the use in hidp_session_run(), with the uninitialized value
originating in __alloc_skb() through vhci_write(). The control path
produces two reports and the interrupt path produces one.
The byte can also be controlled by a malformed lower-layer packet. If an
HCI ACL packet contains an L2CAP PDU with a declared zero-length payload
followed by an extra 0x15 byte, l2cap_recv_acldata() reduces skb->len to
the declared PDU length before dispatch. The current HIDP path nevertheless
consumes the extra byte as HIDP_TRANS_HID_CONTROL |
HIDP_CTRL_VIRTUAL_CABLE_UNPLUG and terminates the HIDP session. With this
change, the same packet is discarded and a subsequent feature report
request succeeds.
Pull the transaction header with skb_pull_data() and discard frames that
do not contain it. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: HIDP: validate numbered report payloads
When hidp_get_raw_report() waits for a numbered report,
hidp_process_data() compares the expected report number with skb->data[0].
A connected HIDP peer can reply with only a DATA transaction header,
leaving the skb empty after the header is removed.
KMSAN reports an uninitialized-value use in hidp_session_run(), with the
value originating in __alloc_skb() through vhci_write(). The transaction
header checks remove the empty-frame reports, but this report remains until
the payload check is added.
The comparison can also consume a peer-controlled byte beyond the declared
L2CAP PDU. A DATA | FEATURE response followed by an extra 0x01 byte made
the current code accept that byte as report ID 1 and complete
HIDIOCGFEATURE with a zero-byte result. With this change the malformed
response is rejected with -EIO, while a subsequent valid response still
succeeds.
Require a payload byte before comparing a numbered report ID. Unnumbered
reports continue to accept an empty payload. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/vmwgfx: validate DRAW_PRIMITIVES header size before division
vmw_cmd_draw() computes
maxnum = (header->size - sizeof(cmd->body)) / sizeof(*decl);
where header->size is u32 and is taken straight from the user-supplied
command stream. When header->size is less than sizeof(cmd->body) the
unsigned subtraction wraps to nearly 4 GiB, producing a huge maxnum.
Any user-controlled cmd->body.numVertexDecls then passes the bound and
the loop dereferences decl[i] far past the end of the kernel command
bounce buffer, producing an out-of-bounds read of kernel memory.
Reject undersized headers up front. |
| In the Linux kernel, the following vulnerability has been resolved:
macsec: don't read an unset MAC header in macsec_encrypt()
macsec_encrypt() reads the Ethernet header via eth_hdr(skb)
(skb->head + skb->mac_header) to memmove() the 12 source/destination MAC
bytes forward and make room for the SecTAG.
On the AF_PACKET SOCK_RAW + PACKET_QDISC_BYPASS transmit path the skb
reaches the macsec ndo_start_xmit() with the MAC header unset, so
eth_hdr(skb) resolves to skb->head + (u16)~0 and the read is out of
bounds: a 12-byte heap over-read that is also emitted on the wire as the
frame's outer source/destination MAC. KASAN reports a slab-out-of-bounds
read in macsec_start_xmit() on 6.0; on current mainline a CONFIG_DEBUG_NET
build flags it as an unset mac header in skb_mac_header().
On the TX path the L2 header is at skb->data, so use skb_eth_hdr(), added
by commit 96cc4b69581d ("macvlan: do not assume mac_header is set in
macvlan_broadcast()") for exactly this purpose. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote attacker to cause a denial of service due to an off-by-one error in bounds checking. |
| In the Linux kernel, the following vulnerability has been resolved:
libceph: bound get_version reply decode to front len
handle_get_version_reply() uses msg->front_alloc_len as the decode
boundary for MON_GET_VERSION_REPLY. That is the size of the reused
reply buffer, not the number of bytes actually received.
A truncated reply can therefore pass ceph_decode_need() and decode the
second u64 from stale tail bytes left in the buffer by an earlier
message, causing an uninitialized memory read.
Use msg->front.iov_len as the receive-side decode boundary, matching
other libceph reply handlers and limiting decoding to the bytes that
were actually read from the wire. |
| IBM i 7.6, 7.5, 7.4, and 7.3 could allow a remote attacker to obtain sensitive information due to an out-of-bounds read. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: bound element ID read when checking non-inheritance
cfg80211_is_element_inherited() reads the first data octet of the
candidate element (id = elem->data[0]) to look it up in an extension
non-inheritance list. It does so after testing elem->id, but without
verifying that the element actually has a data octet. A zero-length
extension element (WLAN_EID_EXTENSION with length 0) therefore makes it
read one octet past the end of the element.
_ieee802_11_parse_elems_full() runs this check for every element of a
frame once a non-inheritance context exists -- e.g. while parsing a
per-STA profile of a Multi-Link element in a (re)association response,
or a non-transmitted BSS profile -- so a crafted frame from an AP can
trigger a one-octet slab-out-of-bounds read during element parsing:
BUG: KASAN: slab-out-of-bounds in cfg80211_is_element_inherited
Read of size 1 ... in net/wireless/scan.c
Return early (treat the element as inherited) when an extension element
carries no data, mirroring the existing handling of empty ID lists.
The bug was found by fuzzing ieee802_11_parse_elems_full() under KASAN. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: at76c50x-usb: avoid length underflow in at76_guess_freq()
at76_guess_freq() checks only that the received frame is at least a bare
802.11 header (24 bytes) before subtracting the fixed management-body
offset:
len -= el_off;
For both beacon and probe response frames, el_off is 36. If the frame is
shorter than el_off, subtracting it causes the calculated IE length to
wrap. The length is eventually passed to cfg80211_find_elem_match() as a
very large unsigned value, so the element walk runs beyond the RX skb.
This path is reached from at76_rx_tasklet() while scanning. If the device
delivers a truncated beacon or probe response, the oversized IE length
causes an out-of-bounds read during scanning.
Skip the IE lookup if the frame does not reach the variable elements,
before subtracting el_off. |
