| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| Improper isolation of shared resources within the CPU operation cache on Zen 2-based products could allow an attacker to corrupt instructions executed at a different privilege level, potentially resulting in privilege escalation. |
| A malicious SSH peer could send unsolicited global request responses to fill an internal buffer, blocking the connection's read loop. The blocked goroutine could not be released by calling Close(), resulting in a resource leak per connection. Unsolicited global responses are now discarded. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix double-free in SMB2_close() replay
A response-bearing attempt can return a replayable error and free its
response buffer. If SMB2_close_init() fails before the next send, cleanup
retains the previous buffer type and frees that response again.
Reset response bookkeeping before each attempt to prevent the stale free. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: fix 32-bit overflow in CWSR total size calculation
total_cwsr_size was computed in 32-bit before being used as a BO/SVM
allocation size.
With large ctx_save_restore_area_size and debug_memory_size
multiplied by the XCC count, the product can wrap,
yielding an undersized CWSR save area that firmware later overruns.
Promote total_cwsr_size to u64 and use check_add_overflow()/
check_mul_overflow() in both kfd_queue_acquire_buffers() and
kfd_queue_release_buffers().
(cherry picked from commit 319f7e13423ae3f486b9aea82f9ad2d6af0ee608) |
| Vault Secrets Operator 1.3.0 up to 1.4.1 is vulnerable to an arbitrary file read and credential exfiltration issue in the AppRole authentication configuration that may allow a tenant with limited Kubernetes RBAC permissions to read files from the operator pod's filesystem and transmit their contents to a tenant-controlled endpoint, potentially leading to privilege escalation within the cluster. This vulnerability (CVE-2026-8715) is fixed in Vault Secrets Operator 1.5.0. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/vce: fix integer overflow in image size
Fix a security vulnerability where malicious VCE command streams
with oversized dimensions (e.g. 65536×65536) cause 32-bit integer
overflow, wrapping the calculated buffer size to 0. This bypasses
validation and allows GPU firmware to perform out-of-bound memory
access.
The fix uses 64-bit arithmetic to detect overflow and rejects
invalid dimensions before they reach the hardware.
V2: remove redundant check
V3: modify max height value
V4: remove size64
(cherry picked from commit cbe408dba581755ad1279a487ec786d8927d778d) |
| In the Linux kernel, the following vulnerability has been resolved:
gve: fix Rx queue stall on alloc failure
When the system is under extreme memory pressure, page allocations can
fail during the Rx buffer refill loop. If the number of buffers posted
to hardware falls below a critical low threshold and the refill loop
exits due to allocation failures, the queue can stall:
1. The device drops incoming packets because there are no descriptors.
2. Since no packets are processed, no Rx completions are generated.
3. Because no completions occur, NAPI is never scheduled, preventing
the refill loop from running again even after memory is freed.
This results in a permanent queue stall.
Resolve this by introducing a starvation recovery timer for each Rx queue.
If the number of buffers posted to hardware falls below a critical low
threshold, start a timer to periodically reschedule NAPI. Once NAPI runs
and successfully refills the queue above the threshold, the timer is
not rescheduled.
The threshold is set to 32 because a single maximum-sized Receive Segment
Coalescing (RSC) packet can consume up to 19 descriptors in the Rx path.
Lower thresholds (such as 8 or 16) would be insufficient to process a
complete maximum-sized RSC packet, risking packet drops or unexpected
hardware behavior under memory pressure. Setting the threshold to 32
guarantees a safe margin to handle at least one full RSC packet. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath6kl: fix OOB access from firmware ADDBA window size
aggr_recv_addba_req_evt() logs a debug message when the firmware-supplied
win_sz is outside [AGGR_WIN_SZ_MIN, AGGR_WIN_SZ_MAX] but does not
return. The out-of-range win_sz is then used in TID_WINDOW_SZ() to
compute a kzalloc size and stored in rxtid->hold_q_sz, leading to
zero-size or overflowed allocations and subsequent out-of-bounds access.
Clean up any previously active aggregation session for the TID first,
then return early when win_sz is out of the valid range, instead of
proceeding with a broken allocation size. |
| In the Linux kernel, the following vulnerability has been resolved:
media: pwc: Return queued buffers on start_streaming() failure
The vb2 framework hands buffers to the driver via buf_queue() before
calling start_streaming(). If start_streaming() returns an error
without first returning those buffers via vb2_buffer_done(),
vb2_start_streaming() fires WARN_ON(owned_by_drv_count) and the queued
buffers leak.
pwc's start_streaming() had two early returns that hit this trap:
-ENODEV when the USB device was already disconnected, and -ERESTARTSYS
when mutex_lock_interruptible() was interrupted by a signal. Call the
existing pwc_cleanup_queued_bufs() helper with VB2_BUF_STATE_QUEUED
before returning (matching the state already used by the
pwc_isoc_init() error path in the same function).
This mirrors the uvcvideo fix in commit 4cf3b6fd54eb ("media: uvcvideo:
Return queued buffers on start_streaming() failure"). |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: tas2781: bound firmware description string parsing
The TAS2781 firmware parser reads several variable-length description
strings with strlen() before checking that the string terminator is
present inside the firmware blob. A malformed firmware image without a
NUL terminator can therefore make the parser walk past the end of the
firmware buffer before the later size checks run.
Add a small bounded string-length helper and use it for all description
fields that are parsed from the firmware buffer. Keep the existing size
checks for the fixed bytes that follow each string. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix UAF in sock clone early bailouts
Similar to recent commit 9b51a6155d14 ("bpf,fork: wipe ->bpf_storage
before bailouts that access it"), sk_clone() performs an initial
shallow copy of the socket field ->sk_bpf_storage via sock_copy()
for the cloned socket newsk.
If sk_clone() bails out early (e.g. if sk_filter_charge() fails) prior
to calling bpf_sk_storage_clone(), newsk->sk_bpf_storage still points
to the parent socket's BPF local storage. When newsk is subsequently
freed via sk_free(), the deallocation path (__sk_destruct() ->
bpf_sk_storage_free()) destroys the parent socket's BPF local storage,
leading to a use-after-free (UAF) on the parent socket.
Fix this by resetting newsk->sk_bpf_storage to NULL immediately after
sock_copy() in sk_clone(), and remove the now redundant initialization
from bpf_sk_storage_clone(). |
| A vulnerability was found in francoisjacquet RosarioSIS up to 12.8. This issue affects some unknown processing of the file Modules.php. Performing a manipulation results in cross-site request forgery. Remote exploitation of the attack is possible. Upgrading to version 12.9 is capable of addressing this issue. The patch is named 801a71272c82cf4bf695fdc5ed42a9b7511d124d. It is recommended to upgrade the affected component. |
| A vulnerability has been found in francoisjacquet RosarioSIS up to 12.7.4. This vulnerability affects unknown code of the file modules/Students/includes/Medical.inc.php of the component Student Medical Module. Such manipulation of the argument table leads to sql injection. The attack may be launched remotely. Upgrading to version 12.8 is able to resolve this issue. The name of the patch is 6234a0ee0124c0667c824693ac77164f18946ddf. Upgrading the affected component is recommended. |
| In the Linux kernel, the following vulnerability has been resolved:
net: usb: catc: enable basic endpoint checking
catc_probe() fills three URBs with hardcoded endpoint pipes without
verifying the endpoint descriptors:
- usb_sndbulkpipe(usbdev, 1) and usb_rcvbulkpipe(usbdev, 1) for TX/RX
- usb_rcvintpipe(usbdev, 2) for interrupt status
A malformed USB device can present these endpoints with transfer types
that differ from what the driver assumes.
Add a catc_usb_ep enum for endpoint numbers, replacing magic constants
throughout. Add usb_check_bulk_endpoints() and usb_check_int_endpoints()
calls after usb_set_interface() to verify endpoint types before use,
rejecting devices with mismatched descriptors at probe time.
Similar to
- commit 90b7f2961798 ("net: usb: rtl8150: enable basic endpoint checking")
which fixed the issue in rtl8150. |
| In the Linux kernel, the following vulnerability has been resolved:
fscrypt: Avoid dynamic allocation in fscrypt_get_devices()
When a blk_crypto_key starts being used or is evicted, fs/crypto/ calls
fscrypt_get_devices() to get the filesystem's list of block devices,
then iterates over them and calls blk_crypto_config_supported(),
blk_crypto_start_using_key(), or blk_crypto_evict_key() on each one.
Currently, the block device pointers are placed in a dynamically
allocated array. This dynamic allocation is problematic because:
- It can fail, especially at the fscrypt_destroy_inline_crypt_key() call
site when it's invoked for inode eviction under direct reclaim.
- fscrypt_destroy_inline_crypt_key() doesn't handle the failure. It
just zeroizes and frees the blk_crypto_key without calling
blk_crypto_evict_key(). That causes a use-after-free.
For now, let's fix this in the straightforward and easily-backportable
way by switching to an on-stack array. Currently the fscrypt
multi-device functionality is used only by f2fs, which has a hardcoded
limit of 8 block devices. An on-stack array works fine for that.
(Of course, this solution won't scale up to large number of block
devices. For that we'd need a different solution, like moving the block
device iteration into the filesystem. Or in the case of btrfs, which
will only support blk-crypto-fallback, we should make it just call
blk-crypto-fallback directly, so the block devices won't be needed.) |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: timer: don't re-enter an instance callback that is still running
The userspace-driven timer (utimer) TRIGGER ioctl calls
snd_timer_interrupt() directly with no serialization, so two threads
triggering the same utimer can run snd_timer_interrupt() on one
snd_timer concurrently.
snd_timer_process_callbacks() drops timer->lock around each instance
callback and marks the in-flight callback with the single
SNDRV_TIMER_IFLG_CALLBACK bit; snd_timer_close_locked() waits on that
bit to drain an in-flight callback before freeing the instance. The bit
cannot represent two concurrent callbacks: when a second interrupt
re-queues an instance whose callback is still running, both run at once,
the first to finish clears the bit, and the close-path drain then frees
the instance (and its callback_data) while the other callback is still
live - a use-after-free reachable by any user able to open
/dev/snd/timer, both via a user timer instance and via a sequencer queue
timer bound to the utimer.
snd_timer_interrupt() sets IFLG_CALLBACK before dropping timer->lock, so
a concurrent interrupt already observes it under the lock. Skip
re-queuing an instance (and its slaves) to the ack/sack list while its
callback is in flight; the accumulated pticks are delivered on the next
tick, so no event is lost. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: seq: close a re-opened queue timer in the destructor
queue_delete() closes the queue timer, then frees it. snd_seq_timer_close()
clears q->timer->timeri. snd_use_lock_sync() then drains borrowers, and
snd_seq_timer_delete() frees q->timer.
A borrower can re-open the timer inside that window. A SET_QUEUE_CLIENT
that took a queueptr() use_lock reference before the queue was unlinked
runs snd_seq_timer_open() after the close. Open refuses re-open only while
timeri is set, and the close just cleared it, so it re-opens timeri.
snd_seq_timer_delete() does not close that instance. Its snd_seq_timer_stop()
is a no-op, because running was cleared first. So it frees q->timer with the
instance still live. The queue is freed next.
The instance stays on the global timer with callback_data pointing at the
freed queue. A non-owner START on the unlocked queue arms it. The next tick
derefs the freed queue in snd_seq_timer_interrupt().
Reachable by an unprivileged user with access to /dev/snd/seq. No CAP and
no queue ownership required.
Close any lingering instance in the destructor. There, ->timeri can no
longer change: the queue is unlinked and all use_lock borrowers have
drained, so no snd_seq_queue_use() can re-open it. Close it before clearing
q->timer. snd_timer_close() waits for any in-flight snd_seq_timer_interrupt()
to finish, and that callback still reads q->timer (via snd_seq_check_queue()),
so q->timer must stay valid until it drains. |
| streama contains an insecure direct object reference vulnerability in ViewingStatusController that allows authenticated users to read and delete other users' viewing status records. Attackers can enumerate all users' watch progress, delete arbitrary viewing history, and manipulate other users' Continue Watching dashboards by supplying arbitrary primary keys without ownership verification. |
| In the Linux kernel, the following vulnerability has been resolved:
openvswitch: fix GSO userspace truncation underflow
OVS_ACTION_ATTR_TRUNC currently stores a delta from the original skb
length in OVS_CB(skb)->cutlen. When a later userspace action segments a
GSO skb, queue_gso_packets() reuses that delta for each smaller segment.
A segment can then reach queue_userspace_packet() with cutlen greater
than skb->len, underflowing the length passed to skb_zerocopy().
Store the maximum preserved length instead and bound each consumer
against the current skb length. Use U32_MAX as the no-truncation
sentinel so the value remains valid if skb geometry changes before a
consumer handles it. |
| In the Linux kernel, the following vulnerability has been resolved:
mctp: serial: handle zero-length frames to prevent rx buffer overflow
The MCTP serial receive state machine reads a frame length byte in
mctp_serial_push_header() case 2 and validates it upper-bound-only:
if (c > MCTP_SERIAL_FRAME_MTU) {
dev->rxstate = STATE_ERR;
} else {
dev->rxlen = c;
dev->rxpos = 0;
dev->rxstate = STATE_DATA;
...
}
A length of zero passes this check, so rxlen is set to 0 and the state
machine advances to STATE_DATA. In mctp_serial_push() STATE_DATA, the
incoming byte is stored and rxpos incremented before the terminator is
dev->rxbuf[dev->rxpos] = c;
dev->rxpos++;
dev->rxstate = STATE_DATA;
if (dev->rxpos == dev->rxlen) {
dev->rxpos = 0;
dev->rxstate = STATE_TRAILER;
}
With rxlen == 0 the "rxpos == rxlen" terminator can never fire (rxpos is
already 1 on the first data byte), so subsequent bytes are written past
the end of the fixed 74-byte rxbuf, which is the last member of the
netdev private area. Every following data byte is an attacker-controlled
1-byte out-of-bounds heap write, and the overflow continues until a
frame (0x7e) or escape byte resets the parser -- effectively unbounded.
Reaching this requires CAP_NET_ADMIN to attach the N_MCTP line
discipline and bring the resulting mctpserialN netdev up, after which
the bytes arrive via the tty receive path.
Route a zero-length frame straight to STATE_TRAILER instead of
STATE_DATA. The trailer/framing bytes are still consumed, and the frame
resolves to a zero-length skb that the MCTP core rejects; the parser
never enters STATE_DATA with rxlen == 0, so the out-of-bounds write can
no longer occur.
KASAN, on a frame of 0x7e 0x01 0x00 followed by data bytes (before this
change):
UBSAN: array-index-out-of-bounds in drivers/net/mctp/mctp-serial.c:370
index 74 is out of range for type 'u8 [74]'
BUG: KASAN: slab-out-of-bounds in mctp_serial_tty_receive_buf
Write of size 1 at addr ... by task kworker/u16:0
mctp_serial_tty_receive_buf
tty_ldisc_receive_buf
flush_to_ldisc
Allocated by task 152:
alloc_netdev_mqs
mctp_serial_open
v2: route zero-length frames to STATE_TRAILER instead of STATE_ERR so
the trailer/framing bytes are still consumed (Jeremy Kerr).
Found by 0sec automated security-research tooling (https://0sec.ai). |
