| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: conntrack_irc: fix possible out-of-bounds read
When parsing fails after we've matched the command string we
should bail out instead of trying to match a different command.
This helper should be deprecated, given prevalence of TLS I doubt it has
any relevance in 2026. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nft_ct: bail out on template ct in get eval
I noticed this issue while looking at a historic syzbot report [1].
A rule like the one below is enough to trigger the bug:
table ip t {
chain pre {
type filter hook prerouting priority raw;
ct zone set 1
ct original saddr 1.2.3.4 accept
}
}
The first expression attaches a per-cpu template ct via
nft_ct_set_zone_eval() (nf_ct_tmpl_alloc -> kzalloc, tuple is all
zero, nf_ct_l3num(ct) == 0). The next expression then calls
nft_ct_get_eval() on the same skb, treats the template as a real ct
and hits the 16-byte memcpy path. With dreg at NFT_REG32_15 this
overflows past struct nft_regs on the kernel stack; with smaller
dreg values it silently clobbers adjacent registers.
Reject template ct at the eval entry and in nft_ct_get_fast_eval(),
mirroring the check nft_ct_set_eval() already has. Additionally,
bound the address copy in NFT_CT_SRC / NFT_CT_DST by priv->len
instead of by nf_ct_l3num(ct): nf_ct_get_tuple() zeroes the tuple
before pkt_to_tuple() fills in only the protocol-relevant leading
bytes, so the trailing bytes of tuple->{src,dst}.u3.all are
well-defined zero. priv->len is validated at rule load, so the
copy size is now bounded by the destination register rather than
by an untrusted field on the conntrack.
[1]: https://syzkaller.appspot.com/bug?id=389cf09cb72926114fce90dc85a2c3231dcb647c |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: bridge: make ebt_snat ARP rewrite writable
The ebtables SNAT target keeps the Ethernet source address rewrite
behind skb_ensure_writable(skb, 0). This is intentional: at the bridge
ebtables hooks the Ethernet header is addressed through
skb_mac_header()/eth_hdr(), while skb->data points at the Ethernet
payload. Asking skb_ensure_writable() for ETH_HLEN bytes would check
the payload, not the Ethernet header, and would reintroduce the small
packet regression fixed by commit 63137bc5882a.
However, the optional ARP sender hardware address rewrite is different.
It writes through skb_store_bits() at an offset relative to skb->data:
skb_store_bits(skb, sizeof(struct arphdr), info->mac, ETH_ALEN)
skb_header_pointer() only safely reads the ARP header; it does not make
the later sender hardware address range writable. If that range is
still held in a nonlinear skb fragment backed by a splice-imported file
page, skb_store_bits() maps the frag page and copies the new MAC address
directly into it.
Ensure the ARP SHA range is writable before reading the ARP header and
before calling skb_store_bits(). |
| In the Linux kernel, the following vulnerability has been resolved:
dm cache policy smq: check allocation under invalidate lock
commit 2d1f7b65f5de ("dm cache policy smq: fix missing locks in
invalidating cache blocks") added mq->lock around the destructive part of
smq_invalidate_mapping(), but left the e->allocated check outside the
critical section.
That leaves a check-then-act race. Two concurrent invalidators can both
observe e->allocated as true before either of them takes mq->lock. The
first invalidator that acquires the lock removes the entry from the
queues and hash table and then calls free_entry(), which clears
e->allocated and puts the entry back on the free list. The second
invalidator can then acquire mq->lock and continue with the stale result
of the unlocked check.
This can corrupt the SMQ queues or hash table by deleting an entry that
is no longer on those structures. It can also hit the allocation check in
free_entry() when the same entry is freed again.
Move the allocation check under mq->lock so the predicate and the
destructive operations are serialized by the same lock. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: act_api: use RCU with deferred freeing for action lifecycle
When NEWTFILTER and DELFILTER are run concurrently it is possible to create a
race with an associated action.
Let's illustrate with CPU0 running NEWTFILTER and CPU1 running DELFILTER:
0: mutex_lock() <-- holds the idr lock
0: rcu_read_lock()
0: p = idr_find(idr, index) <-- action p is valid (RCU protects IDR)
0: mutex_unlock() <-- releases the idr lock
1: refcount_dec_and_mutex_lock() <-- refcnt 1->0, mutex held
1: idr_remove(idr, index) <-- Action removed from IDR
1: mutex_unlock() <-- mutex released allowing us to delete the action
1: tcf_action_cleanup(p); kfree(p) <-- Kfrees p immediately, no deferral
0: refcount_inc_not_zero(&p->tcfa_refcnt) <-- ouch, UAF p points to freed memory
This patch fixes the race condition between NEWTFILTER and DELFILTER by
adding struct rcu_head to tc_action used in the deferral and introducing a
call_rcu() in the delete path to defer the final kfree().
Note: this is a revert of commit d7fb60b9cafb ("net_sched: get rid of tcfa_rcu")
but also modernization/simplification to directly use kfree_rcu().
Let's illustrate the new restored code path:
0: rcu_read_lock()
1: refcount_dec_and_mutex_lock() <-- refcnt 1->0, mutex held
1: idr_remove(idr, index)
1: mutex_unlock()
1: call_rcu(&p->tcfa_rcu, tcf_action_rcu_free) <-- defer kfree after grace period
0: p = idr_find(idr, index)
0: refcount_inc_not_zero(&p->tcfa_refcnt) <-- fails, refcnt already 0
1: rcu_read_unlock() <-- release so freeing can run after grace period
After CPU1 calls idr_remove(), the object is no longer reachable through the IDR.
CPU0's subsequent idr_find() will return NULL, and even if it still held a
stale pointer, the immediate kfree() is now deferred until after the RCU grace
period, so no UAF can occur. |
| In the Linux kernel, the following vulnerability has been resolved:
l2tp: pppol2tp: hold reference to session in pppol2tp_ioctl()
pppol2tp_ioctl() read sock->sk->sk_user_data directly without any
locks or reference counting. If a controllable sleep was induced during
copy_from_user() (e.g. via a userfaultfd page fault sleep), a concurrent
socket close could trigger pppol2tp_session_close() asynchronously. This
frees the l2tp_session structure via the l2tp_session_del_work workqueue.
Upon resuming, the ioctl thread dereferences the stale session pointer,
resulting in a Use-After-Free (UAF).
Fix this by securely fetching the session reference using the RCU-safe,
refcounted helper pppol2tp_sock_to_session(sk) on entry. This locks the
session's refcount across the sleep. We structured the function to exit
via standard err breaks, guaranteeing that l2tp_session_put() is cleanly
called on all return paths to drop the reference.
To preserve existing behavior we validate the session and its magic
signature only for the specific L2TP commands that require it. This
ensures that generic/unknown ioctls called on an unconnected socket
still return -ENOIOCTLCMD and correctly fall back to generic handlers
(e.g. in sock_do_ioctl()). |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: Add preempt_{disable,enable}_nested() in reqsk_queue_hash_req().
syzbot reported a weird reqsk->rsk_refcnt underflow in
__inet_csk_reqsk_queue_drop().
The captured reqsk_put() in __inet_csk_reqsk_queue_drop()
is called only when it successfully removes reqsk from ehash.
Moreover, reqsk_timer_handler() calls another reqsk_put()
after that.
This indicates that the reqsk was missing both refcnts for
ehash and the timer itself.
Since all the syzbot reports had PREEMPT_RT enabled, the only
possible scenario is that reqsk_queue_hash_req() is preempted
after mod_timer() and before refcount_set(), and then the timer
triggered after 1s aborts the reqsk due to its listener's close().
Let's wrap mod_timer() and refcount_set() with
preempt_disable_nested() and preempt_enable_nested().
Note that inet_ehash_insert() holds the normal spin_lock()
(mutex in PREEMPT_RT), so it must be called outside of
preempt_disable_nested(), but this is fine.
The lookup path just ignores 0 sk_refcnt entries in ehash
and tries to create another reqsk, but this will fail at
inet_ehash_insert().
[0]:
refcount_t: underflow; use-after-free.
WARNING: lib/refcount.c:28 at refcount_warn_saturate+0xb2/0x110 lib/refcount.c:28, CPU#0: ktimers/0/16
Modules linked in:
CPU: 0 UID: 0 PID: 16 Comm: ktimers/0 Tainted: G L syzkaller #0 PREEMPT_{RT,(full)}
Tainted: [L]=SOFTLOCKUP
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/18/2026
RIP: 0010:refcount_warn_saturate+0xb2/0x110 lib/refcount.c:28
Code: e4 7d d1 0a 67 48 0f b9 3a eb 4a e8 38 3d 23 fd 48 8d 3d e1 7d d1 0a 67 48 0f b9 3a eb 37 e8 25 3d 23 fd 48 8d 3d de 7d d1 0a <67> 48 0f b9 3a eb 24 e8 12 3d 23 fd 48 8d 3d db 7d d1 0a 67 48 0f
RSP: 0000:ffffc90000157948 EFLAGS: 00010246
RAX: ffffffff84a1301b RBX: 0000000000000003 RCX: ffff88801ca98000
RDX: 0000000000000100 RSI: 0000000000000000 RDI: ffffffff8f72ae00
RBP: ffffffff99ae3b01 R08: ffff88801ca98000 R09: 0000000000000005
R10: 0000000000000100 R11: 0000000000000004 R12: ffff8880425ef568
R13: ffff8880425ef4f8 R14: ffff8880425ef578 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff888126386000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f7b46710e9c CR3: 000000000dbb6000 CR4: 00000000003526f0
Call Trace:
<TASK>
__refcount_sub_and_test include/linux/refcount.h:400 [inline]
__refcount_dec_and_test include/linux/refcount.h:432 [inline]
refcount_dec_and_test include/linux/refcount.h:450 [inline]
reqsk_put include/net/request_sock.h:136 [inline]
__inet_csk_reqsk_queue_drop+0x3ce/0x440 net/ipv4/inet_connection_sock.c:1007
reqsk_timer_handler+0x651/0xdf0 net/ipv4/inet_connection_sock.c:1137
call_timer_fn+0x192/0x5e0 kernel/time/timer.c:1748
expire_timers kernel/time/timer.c:1799 [inline]
__run_timers kernel/time/timer.c:2374 [inline]
__run_timer_base+0x6a3/0x9f0 kernel/time/timer.c:2386
run_timer_base kernel/time/timer.c:2395 [inline]
run_timer_softirq+0x67/0x170 kernel/time/timer.c:2403
handle_softirqs+0x1de/0x6d0 kernel/softirq.c:622
__do_softirq kernel/softirq.c:656 [inline]
run_ktimerd+0x69/0x100 kernel/softirq.c:1151
smpboot_thread_fn+0x541/0xa50 kernel/smpboot.c:160
kthread+0x388/0x470 kernel/kthread.c:436
ret_from_fork+0x514/0xb70 arch/x86/kernel/process.c:158
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: anycast: insert aca into global hash under idev->lock
syzbot reported a splat [1]: a slab-use-after-free in
ipv6_chk_acast_addr(), which walks the global inet6_acaddr_lst[] hash
under RCU and dereferences a struct ifacaddr6 that has already been
freed while still linked in the hash, so a later reader walks into a
dangling node.
In __ipv6_dev_ac_inc() the aca is allocated with refcount 1, then
aca_get() bumps it to 2 to keep it alive across the unlocked region.
It is published to idev->ac_list under idev->lock, but
ipv6_add_acaddr_hash() runs after write_unlock_bh(). A concurrent
teardown (ipv6_ac_destroy_dev() from addrconf_ifdown(), under RTNL)
can slip into that window:
CPU0 __ipv6_dev_ac_inc CPU1 ipv6_ac_destroy_dev (RTNL)
------------------------------ ------------------------------------
aca_alloc() refcnt 1
aca_get() refcnt 2
write_lock_bh(idev->lock)
add aca to ac_list
write_unlock_bh(idev->lock)
write_lock_bh(idev->lock)
pull aca off ac_list
write_unlock_bh(idev->lock)
ipv6_del_acaddr_hash(aca)
hlist_del_init_rcu() is a no-op,
aca is not in the hash yet
aca_put() refcnt 2->1
ipv6_add_acaddr_hash(aca)
aca now inserted into the hash
aca_put() refcnt 1->0
call_rcu(aca_free_rcu) -> kfree(aca)
The hash removal becomes a no-op because the insertion has not
happened yet, so once CPU0 inserts and drops the last reference, the
aca is freed while still linked in inet6_acaddr_lst[], and readers
dereference freed memory after the slab slot is reused.
This window opened once RTNL stopped serializing the join path against
device teardown. Move ipv6_add_acaddr_hash() inside the idev->lock
section so the ac_list and hash insertions are atomic with respect to
teardown: a racing remover now either misses the aca entirely or finds
it in both lists.
acaddr_hash_lock is now nested under idev->lock, which is acquired in
softirq context, so switch all acaddr_hash_lock sites to spin_lock_bh()
to avoid the irq lock inversion reported in [2].
[1] https://syzkaller.appspot.com/bug?extid=a01df04303c131efbf3a
[2] https://lore.kernel.org/netdev/[email protected]/ |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: RFCOMM: hold listener socket in rfcomm_connect_ind()
rfcomm_get_sock_by_channel() scans rfcomm_sk_list under the list lock,
but returns the selected listener after dropping that lock without
taking a reference. rfcomm_connect_ind() then locks the listener,
queues a child socket on it, and may notify it after unlocking it.
The buggy scenario involves two paths, with each column showing the
order within that path:
rfcomm_connect_ind(): listener close:
1. Find parent in 1. close() enters
rfcomm_get_sock_by_channel() rfcomm_sock_release().
2. Drop rfcomm_sk_list.lock 2. rfcomm_sock_shutdown()
without pinning parent. closes the listener.
3. Call lock_sock(parent) and 3. rfcomm_sock_kill()
bt_accept_enqueue(parent, unlinks and puts parent.
sk, true).
4. Read parent flags and may 4. parent can be freed.
call sk_state_change().
If close wins the race, parent can be freed before
rfcomm_connect_ind() reaches lock_sock(), bt_accept_enqueue(), or the
deferred-setup callback.
Take a reference on the listener before leaving rfcomm_sk_list.lock.
After lock_sock() succeeds, recheck that it is still in BT_LISTEN
before queueing a child, cache the deferred-setup bit while the parent
is locked, and drop the reference after the last parent use.
KASAN reported a slab-use-after-free in lock_sock_nested() from
rfcomm_connect_ind(), with the freeing stack going through
rfcomm_sock_kill() and rfcomm_sock_release(). |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: RFCOMM: validate skb length in MCC handlers
The RFCOMM MCC handlers cast skb->data to protocol-specific structs
without validating skb->len first. A malicious remote device can send
truncated MCC frames and trigger out-of-bounds reads in these handlers.
Fix this by using skb_pull_data() to validate and access the required
data before dereferencing it.
rfcomm_recv_rpn() requires special handling since ETSI TS 07.10 allows
1-byte RPN requests. Handle this by validating only the DLCI byte first,
and validating the full struct only when len > 1. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: bnep: reject short frames before parsing
A BNEP peer can send a short BNEP SDU. bnep_rx_frame() reads the
packet type byte immediately and, for control packets, reads the control
opcode and setup UUID-size byte before proving that those bytes are
present. bnep_rx_control() also dereferences the control opcode without
rejecting an empty control payload.
Use skb_pull_data() for the fixed fields in bnep_rx_frame() so a NULL
return gates each dereference. Split the control handler so the frame
path can pass an opcode that has already been pulled, and keep the
byte-buffer wrapper for extension control payloads.
For BNEP_SETUP_CONN_REQ, name the UUID-size byte before pulling the
setup payload. struct bnep_setup_conn_req carries destination and source
service UUIDs after that byte, each uuid_size bytes, so the parser now
documents that tuple explicitly instead of leaving the pull length as an
opaque multiplication.
Validation reproduced this kernel report:
KASAN slab-out-of-bounds in bnep_rx_frame.isra.0+0x130c/0x1790
The buggy address belongs to the object at ffff88800c0f7908 which belongs
to the cache kmalloc-8 of size 8
The buggy address is located 0 bytes to the right of allocated 1-byte
region [ffff88800c0f7908, ffff88800c0f7909)
Read of size 1
Call trace:
dump_stack_lvl+0xb3/0x140 (?:?)
print_address_description+0x57/0x3a0 (?:?)
bnep_rx_frame+0x130c/0x1790 (net/bluetooth/bnep/core.c:306)
print_report+0xb9/0x2b0 (?:?)
__virt_addr_valid+0x1ba/0x3a0 (?:?)
srso_alias_return_thunk+0x5/0xfbef5 (?:?)
kasan_addr_to_slab+0x21/0x60 (?:?)
kasan_report+0xe0/0x110 (?:?)
process_one_work+0xfce/0x17e0 (kernel/workqueue.c:3200)
worker_thread+0x65c/0xe40 (?:?)
__kthread_parkme+0x184/0x230 (?:?)
kthread+0x35e/0x470 (?:?)
_raw_spin_unlock_irq+0x28/0x50 (?:?)
ret_from_fork+0x586/0x870 (?:?)
__switch_to+0x74f/0xdc0 (?:?)
ret_from_fork_asm+0x1a/0x30 (?:?) |
| In the Linux kernel, the following vulnerability has been resolved:
xsk: cache csum_start/csum_offset to fix TOCTOU in xsk_skb_metadata()
The TX metadata area resides in the UMEM buffer which is memory-mapped
and concurrently writable by userspace. In xsk_skb_metadata(),
csum_start and csum_offset are read from shared memory for bounds
validation, then read again for skb assignment. A malicious userspace
application can race to overwrite these values between the two reads,
bypassing the bounds check and causing out-of-bounds memory access
during checksum computation in the transmit path.
Fix this by reading csum_start and csum_offset into local variables
once, then using the local copies for both validation and assignment.
Note that other metadata fields (flags, launch_time) and the cached
csum fields may be mutually inconsistent due to concurrent userspace
writes, but this is benign: the only security-critical invariant is
that each field's validated value is the same one used, which local
caching guarantees. |
| In the Linux kernel, the following vulnerability has been resolved:
net: airoha: Fix use-after-free in metadata dst teardown
airoha_metadata_dst_free() runs metadata_dst_free() which frees the
metadata_dst with kfree() immediately, bypassing the RCU grace period.
In the RX path, skb_dst_set_noref() sets a non-refcounted pointer from
the skb to the metadata_dst. This function requires RCU read-side
protection and the dst must remain valid until all RCU readers complete.
Since metadata_dst_free() calls kfree() directly, an use-after-free can
occur if any skb still holds a noref pointer to the dst when the driver
tears it down.
Replace metadata_dst_free() with dst_release() which properly goes
through the refcount path: when the refcount drops to zero, it schedules
the actual free via call_rcu_hurry(), ensuring all RCU readers have
completed before the memory is freed. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ethernet: mtk_eth_soc: Fix use-after-free in metadata dst teardown
mtk_free_dev() calls metadata_dst_free() which frees the metadata_dst
with kfree() immediately, bypassing the RCU grace period.
In the RX path, skb_dst_set_noref() sets a non-refcounted pointer from
the skb to the metadata_dst. This function requires RCU read-side
protection and the dst must remain valid until all RCU readers complete.
Since metadata_dst_free() calls kfree() directly, a use-after-free can
occur if any skb still holds a noref pointer to the dst when the driver
tears it down.
Replace metadata_dst_free() with dst_release() which properly goes
through the refcount path: when the refcount drops to zero, it schedules
the actual free via call_rcu_hurry(), ensuring all RCU readers have
completed before the memory is freed. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: validate cached peer INIT chunk length in COOKIE_ECHO processing
When a listening SCTP server processes a COOKIE_ECHO chunk, the cached
peer INIT chunk embedded after the cookie is parsed and its parameters
are later walked by sctp_process_init() using sctp_walk_params().
However, the chunk header length of this cached INIT chunk was not
validated against the remaining buffer in the COOKIE_ECHO payload. If
the length field is inflated, the parameter walk can run beyond the
actual received data, leading to out-of-bounds reads and potential
memory corruption during later parameter handling (e.g. STATE_COOKIE
processing and kmemdup() copies).
Add a bounds check in sctp_unpack_cookie() to ensure the cached INIT
chunk length does not exceed the available data in the COOKIE_ECHO
buffer before it is used. |
| In the Linux kernel, the following vulnerability has been resolved:
VFS: fix possible failure to unlock in nfsd4_create_file()
atomic_create() in fs/namei.c drops the reference to the dentry
when it returns an error.
This behaviour was imported into dentry_create() so that it
will drop the reference if an error is returned from atomic_create(),
though not if vfs_create() returns an error (in the case where
->atomic_create is not supported).
The caller - nfsd4_create_file() - is made aware of this by checking
path->dentry, which will either be a counted reference to a dentry, or
an error pointer.
However the change to use start_creating()/end_creating() (which landed
shortly before the dentry_create() change landed, though was likely
developed around the same time) means that nfsd4_create_file() *needs* a
valid dentry so that it can unlock the parent.
The net result is that if NFSD exports a filesystem which uses
->atomic_create, and if a call to ->atomic_create returns an error, then
nfsd4_create_file() will pass an error pointer to end_creating()
and the parent will not be unlocked.
Fix this by changing dentry_create() to make sure path->dentry is always
a valid dentry, never an error-pointer. The actual error is already
returned a different way.
Note that if ->atomic_create() returns a different dentry (which may not
be possible in practice) we are guaranteed (because it is only ever
provided by d_spliace_alias()) that it will have the same d_parent and
so it will have the same effect when passed to end_creating(). |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: PCM: Fix wait queue list corruption in snd_pcm_drain() on linked streams
snd_pcm_drain() uses init_waitqueue_entry which does not clear
entry.prev/next, and add_wait_queue with a conditional
remove_wait_queue that is skipped when to_check is no longer
in the group after concurrent UNLINK. The orphaned wait entry
remains on the unlinked substream sleep queue. On the next
drain iteration, add_wait_queue adds the entry to a new queue
while still linked on the old one, corrupting both lists. A
subsequent wake_up dereferences NULL at the func pointer
(mapped from the spinlock at offset 0 of the misinterpreted
wait_queue_head_t), causing a kernel panic.
Replace init_waitqueue_entry/add_wait_queue/conditional
remove_wait_queue with init_wait_entry/prepare_to_wait/
finish_wait. init_wait_entry clears prev/next via
INIT_LIST_HEAD on each iteration and sets
autoremove_wake_function which auto-removes the entry on
wake-up. finish_wait safely handles both the already-removed
and still-queued cases. |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: iptfs: fix use-after-free on first_skb in __input_process_payload
__input_process_payload() stores first_skb into xtfs->ra_newskb under
drop_lock when starting partial reassembly, then unlocks and breaks out
of the processing loop. The post-loop check reads xtfs->ra_newskb
without the lock to decide whether first_skb is still owned:
if (first_skb && first_iplen && !defer && first_skb != xtfs->ra_newskb)
Between spin_unlock and this read, a concurrent CPU running
iptfs_reassem_cont() (or the drop_timer hrtimer) can complete
reassembly, NULL xtfs->ra_newskb, and free the skb. The check then
evaluates first_skb != NULL as true, and pskb_trim/ip_summed/consume_skb
operate on the freed skb — a use-after-free in skbuff_head_cache.
Replace the unlocked read with a local bool that records whether
first_skb was handed to the reassembly state in the current call. The
flag is set after the existing spin_unlock, before the break, using the
pointer equality that is stable at that point (first_skb == skb iff
first_skb was stored in ra_newskb). |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: policy: fix use-after-free on inexact bin in xfrm_policy_bysel_ctx()
Fix the race by pruning the bin while still holding xfrm_policy_lock,
before dropping it. Use __xfrm_policy_inexact_prune_bin() directly since
the lock is already held. The wrapper xfrm_policy_inexact_prune_bin()
becomes unused and is removed.
Race:
CPU0 (XFRM_MSG_DELPOLICY) CPU1 (XFRM_MSG_NEWSPDINFO)
========================== ==========================
xfrm_policy_bysel_ctx():
spin_lock_bh(xfrm_policy_lock)
bin = xfrm_policy_inexact_lookup()
__xfrm_policy_unlink(pol)
spin_unlock_bh(xfrm_policy_lock)
xfrm_policy_kill(ret)
// wide window, lock not held
xfrm_hash_rebuild():
spin_lock_bh(xfrm_policy_lock)
__xfrm_policy_inexact_flush():
kfree_rcu(bin) // bin freed
spin_unlock_bh(xfrm_policy_lock)
xfrm_policy_inexact_prune_bin(bin)
// UAF: bin is freed |
| In the Linux kernel, the following vulnerability has been resolved:
net: add pskb_may_pull() to skb_gro_receive_list()
skb_gro_receive_list() calls skb_pull(skb, skb_gro_offset(skb)) without
first ensuring the data is in the linear area via pskb_may_pull(). When
the skb arrives via napi_gro_frags(), skb_headlen can be 0 (all data in
page fragments) while skb_gro_offset is non-zero (after IP+TCP header
parsing). The skb_pull() then decrements skb->len by skb_gro_offset
but skb->data_len stays unchanged, hitting BUG_ON(skb->len < skb->data_len)
in __skb_pull().
The UDP fraglist GRO path already contains this guard at
udp_offload.c:749. Adding it to skb_gro_receive_list() itself provides
centralized protection for all callers (TCP, UDP, and any future
protocols), and ensures the precondition of skb_pull() is satisfied
before it is called.
On pskb_may_pull() failure, set NAPI_GRO_CB(skb)->flush = 1 so the
skb is not held as a new GRO head and is instead delivered through the
normal receive path, matching the UDP handling. |
