| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ibmasm: fix heap over-read in ibmasm_send_i2o_message()
The ibmasm_send_i2o_message() function uses get_dot_command_size() to
compute the byte count for memcpy_toio(), but this value is derived from
user-controlled fields in the dot_command_header (command_size: u8,
data_size: u16) and is never validated against the actual allocation size.
A root user can write a small buffer with inflated header fields, causing
memcpy_toio() to read up to ~65 KB past the end of the allocation into
adjacent kernel heap, which is then forwarded to the service processor
over MMIO.
Silently clamping the copy size is not sufficient: if the header fields
claim a larger size than the buffer, the SP receives a dot command whose
own header is inconsistent with the I2O message length, which can cause
the SP to desynchronize. Reject such commands outright by returning
failure.
Validate command_size before calling get_mfa_inbound() to avoid leaking
an I2O message frame: reading INBOUND_QUEUE_PORT dequeues a hardware
frame from the controller's free pool, and returning without a
corresponding set_mfa_inbound() call would permanently exhaust it.
Additionally, clamp command_size to I2O_COMMAND_SIZE before the
memcpy_toio() so the MMIO write stays within the I2O message frame,
consistent with the clamping already performed by outgoing_message_size()
for the header field. |
| In the Linux kernel, the following vulnerability has been resolved:
misc: ibmasm: fix OOB MMIO read in ibmasm_handle_mouse_interrupt()
ibmasm_handle_mouse_interrupt() performs an out-of-bounds MMIO read
when the queue reader or writer index from hardware exceeds
REMOTE_QUEUE_SIZE (60).
A compromised service processor can trigger this by writing an
out-of-range value to the reader or writer MMIO register before
asserting an interrupt. Since writer is re-read from hardware on
every loop iteration, it can also be set to an out-of-range value
after the loop has already started.
The root cause is that get_queue_reader() and get_queue_writer() return
raw readl() values that are passed directly into get_queue_entry(),
which computes:
queue_begin + reader * sizeof(struct remote_input)
with no bounds check. This unchecked MMIO address is then passed to
memcpy_fromio(), reading 8 bytes from unintended device registers.
For sufficiently large values the address falls outside the PCI BAR
mapping entirely, triggering a machine check exception.
Fix by checking both indices against REMOTE_QUEUE_SIZE at the top of
the loop body, before any call to get_queue_entry(). On an out-of-range
value, reset the reader register to 0 via set_queue_reader() before
breaking, so that normal queue operation can resume if the corrupted
hardware state is transient. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: reject negative CO-RE accessor indices in bpf_core_parse_spec()
CO-RE accessor strings are colon-separated indices that describe a path
from a root BTF type to a target field, e.g. "0:1:2" walks through
nested struct members. bpf_core_parse_spec() parses each component with
sscanf("%d"), so negative values like -1 are silently accepted. The
subsequent bounds checks (access_idx >= btf_vlen(t)) only guard the
upper bound and always pass for negative values because C integer
promotion converts the __u16 btf_vlen result to int, making the
comparison (int)(-1) >= (int)(N) false for any positive N.
When -1 reaches btf_member_bit_offset() it gets cast to u32 0xffffffff,
producing an out-of-bounds read far past the members array. A crafted
BPF program with a negative CO-RE accessor on any struct that exists in
vmlinux BTF (e.g. task_struct) crashes the kernel deterministically
during BPF_PROG_LOAD on any system with CONFIG_DEBUG_INFO_BTF=y
(default on major distributions). The bug is reachable with CAP_BPF:
BUG: unable to handle page fault for address: ffffed11818b6626
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
Oops: Oops: 0000 [#1] SMP KASAN NOPTI
CPU: 0 UID: 0 PID: 85 Comm: poc Not tainted 7.0.0-rc6 #18 PREEMPT(full)
RIP: 0010:bpf_core_parse_spec (tools/lib/bpf/relo_core.c:354)
RAX: 00000000ffffffff
Call Trace:
<TASK>
bpf_core_calc_relo_insn (tools/lib/bpf/relo_core.c:1321)
bpf_core_apply (kernel/bpf/btf.c:9507)
check_core_relo (kernel/bpf/verifier.c:19475)
bpf_check (kernel/bpf/verifier.c:26031)
bpf_prog_load (kernel/bpf/syscall.c:3089)
__sys_bpf (kernel/bpf/syscall.c:6228)
</TASK>
CO-RE accessor indices are inherently non-negative (struct member index,
array element index, or enumerator index), so reject them immediately
after parsing. |
| In the Linux kernel, the following vulnerability has been resolved:
net/rds: handle zerocopy send cleanup before the message is queued
A zerocopy send can fail after user pages have been pinned but before
the message is attached to the sending socket.
The purge path currently infers zerocopy state from rm->m_rs, so an
unqueued message can be cleaned up as if it owned normal payload pages.
However, zerocopy ownership is really determined by the presence of
op_mmp_znotifier, regardless of whether the message has reached the
socket queue.
Capture op_mmp_znotifier up front in rds_message_purge() and use it as
the cleanup discriminator. If the message is already associated with a
socket, keep the existing completion path. Otherwise, drop the pinned
page accounting directly and release the notifier before putting the
payload pages.
This keeps early send failure cleanup consistent with the zerocopy
lifetime rules without changing the normal queued completion path. |
| In the Linux kernel, the following vulnerability has been resolved:
rtmutex: Use waiter::task instead of current in remove_waiter()
remove_waiter() is used by the slowlock paths, but it is also used for
proxy-lock rollback in rt_mutex_start_proxy_lock() when invoked from
futex_requeue().
In the latter case waiter::task is not current, but remove_waiter()
operates on current for the dequeue operation. That results in several
problems:
1) the rbtree dequeue happens without waiter::task::pi_lock being held
2) the waiter task's pi_blocked_on state is not cleared, which leaves a
dangling pointer primed for UAF around.
3) rt_mutex_adjust_prio_chain() operates on the wrong top priority waiter
task
Use waiter::task instead of current in all related operations in
remove_waiter() to cure those problems.
[ tglx: Fixup rt_mutex_adjust_prio_chain(), add a comment and amend the
changelog ] |
| In the Linux kernel, the following vulnerability has been resolved:
lib/crypto: mpi: Fix integer underflow in mpi_read_raw_from_sgl()
Yiming reports an integer underflow in mpi_read_raw_from_sgl() when
subtracting "lzeros" from the unsigned "nbytes".
For this to happen, the scatterlist "sgl" needs to occupy more bytes
than the "nbytes" parameter and the first "nbytes + 1" bytes of the
scatterlist must be zero. Under these conditions, the while loop
iterating over the scatterlist will count more zeroes than "nbytes",
subtract the number of zeroes from "nbytes" and cause the underflow.
When commit 2d4d1eea540b ("lib/mpi: Add mpi sgl helpers") originally
introduced the bug, it couldn't be triggered because all callers of
mpi_read_raw_from_sgl() passed a scatterlist whose length was equal to
"nbytes".
However since commit 63ba4d67594a ("KEYS: asymmetric: Use new crypto
interface without scatterlists"), the underflow can now actually be
triggered. When invoking a KEYCTL_PKEY_ENCRYPT system call with a
larger "out_len" than "in_len" and filling the "in" buffer with zeroes,
crypto_akcipher_sync_prep() will create an all-zero scatterlist used for
both the "src" and "dst" member of struct akcipher_request and thereby
fulfil the conditions to trigger the bug:
sys_keyctl()
keyctl_pkey_e_d_s()
asymmetric_key_eds_op()
software_key_eds_op()
crypto_akcipher_sync_encrypt()
crypto_akcipher_sync_prep()
crypto_akcipher_encrypt()
rsa_enc()
mpi_read_raw_from_sgl()
To the user this will be visible as a DoS as the kernel spins forever,
causing soft lockup splats as a side effect.
Fix it. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_ncm: Fix net_device lifecycle with device_move
The network device outlived its parent gadget device during
disconnection, resulting in dangling sysfs links and null pointer
dereference problems.
A prior attempt to solve this by removing SET_NETDEV_DEV entirely [1]
was reverted due to power management ordering concerns and a NO-CARRIER
regression.
A subsequent attempt to defer net_device allocation to bind [2] broke
1:1 mapping between function instance and network device, making it
impossible for configfs to report the resolved interface name. This
results in a regression where the DHCP server fails on pmOS.
Use device_move to reparent the net_device between the gadget device and
/sys/devices/virtual/ across bind/unbind cycles. This preserves the
network interface across USB reconnection, allowing the DHCP server to
retain their binding.
Introduce gether_attach_gadget()/gether_detach_gadget() helpers and use
__free(detach_gadget) macro to undo attachment on bind failure. The
bind_count ensures device_move executes only on the first bind.
[1] https://lore.kernel.org/lkml/[email protected]/
[2] https://lore.kernel.org/linux-usb/[email protected]/ |
| In the Linux kernel, the following vulnerability has been resolved:
ipv4: icmp: fix null-ptr-deref in icmp_build_probe()
ipv6_stub->ipv6_dev_find() may return ERR_PTR(-EAFNOSUPPORT) when the
IPv6 stack is not active (CONFIG_IPV6=m and not loaded), and passing
this error pointer to dev_hold() will cause a kernel crash with
null-ptr-deref.
Instead, silently discard the request. RFC 8335 does not appear to
define a specific response for the case where an IPv6 interface
identifier is syntactically valid but the implementation cannot perform
the lookup at runtime, and silently dropping the request may safer than
misreporting "No Such Interface". |
| In the Linux kernel, the following vulnerability has been resolved:
net: correctly handle tunneled traffic on IPV6_CSUM GSO fallback
NETIF_F_IPV6_CSUM only advertises support for checksum offload of
packets without IPv6 extension headers. Packets with extension
headers must fall back onto software checksumming. Since TSO
depends on checksum offload, those must revert to GSO.
The below commit introduces that fallback. It always checks
network header length. For tunneled packets, the inner header length
must be checked instead. Extend the check accordingly.
A special case is tunneled packets without inner IP protocol. Such as
RFC 6951 SCTP in UDP. Those are not standard IPv6 followed by
transport header either, so also must revert to the software GSO path. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: ti-adc161s626: use DMA-safe memory for spi_read()
Add a DMA-safe buffer and use it for spi_read() instead of a stack
memory. All SPI buffers must be DMA-safe.
Since we only need up to 3 bytes, we just use a u8[] instead of __be16
and __be32 and change the conversion functions appropriately. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: gyro: mpu3050: Move iio_device_register() to correct location
iio_device_register() should be at the end of the probe function to
prevent race conditions.
Place iio_device_register() at the end of the probe function and place
iio_device_unregister() accordingly. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ftgmac100: fix ring allocation unwind on open failure
ftgmac100_alloc_rings() allocates rx_skbs, tx_skbs, rxdes, txdes, and
rx_scratch in stages. On intermediate failures it returned -ENOMEM
directly, leaking resources allocated earlier in the function.
Rework the failure path to use staged local unwind labels and free
allocated resources in reverse order before returning -ENOMEM. This
matches common netdev allocation cleanup style. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: require minimum ACE size in smb_check_perm_dacl()
Both ACE-walk loops in smb_check_perm_dacl() only guard against an
under-sized remaining buffer, not against an ACE whose declared
`ace->size` is smaller than the struct it claims to describe:
if (offsetof(struct smb_ace, access_req) > aces_size)
break;
ace_size = le16_to_cpu(ace->size);
if (ace_size > aces_size)
break;
The first check only requires the 4-byte ACE header to be in bounds;
it does not require access_req (4 bytes at offset 4) to be readable.
An attacker who has set a crafted DACL on a file they own can declare
ace->size == 4 with aces_size == 4, pass both checks, and then
granted |= le32_to_cpu(ace->access_req); /* upper loop */
compare_sids(&sid, &ace->sid); /* lower loop */
reads access_req at offset 4 (OOB by up to 4 bytes) and ace->sid at
offset 8 (OOB by up to CIFS_SID_BASE_SIZE + SID_MAX_SUB_AUTHORITIES
* 4 bytes).
Tighten both loops to require
ace_size >= offsetof(struct smb_ace, sid) + CIFS_SID_BASE_SIZE
which is the smallest valid on-wire ACE layout (4-byte header +
4-byte access_req + 8-byte sid base with zero sub-auths). Also
reject ACEs whose sid.num_subauth exceeds SID_MAX_SUB_AUTHORITIES
before letting compare_sids() dereference sub_auth[] entries.
parse_sec_desc() already enforces an equivalent check (lines 441-448);
smb_check_perm_dacl() simply grew weaker validation over time.
Reachability: authenticated SMB client with permission to set an ACL
on a file. On a subsequent CREATE against that file, the kernel
walks the stored DACL via smb_check_perm_dacl() and triggers the
OOB read. Not pre-auth, and the OOB read is not reflected to the
attacker, but KASAN reports and kernel state corruption are
possible. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: server: fix active_num_conn leak on transport allocation failure
Commit 77ffbcac4e56 ("smb: server: fix leak of active_num_conn in
ksmbd_tcp_new_connection()") addressed the kthread_run() failure
path. The earlier alloc_transport() == NULL path in the same
function has the same leak, is reachable pre-authentication via any
TCP connect to port 445, and was empirically reproduced on UML
(ARCH=um, v7.0-rc7): a small number of forced allocation failures
were sufficient to put ksmbd into a state where every subsequent
connection attempt was rejected for the remainder of the boot.
ksmbd_kthread_fn() increments active_num_conn before calling
ksmbd_tcp_new_connection() and discards the return value, so when
alloc_transport() returns NULL the socket is released and -ENOMEM
returned without decrementing the counter. Each such failure
permanently consumes one slot from the max_connections pool; once
cumulative failures reach the cap, atomic_inc_return() hits the
threshold on every subsequent accept and every new connection is
rejected. The counter is only reset by module reload.
An unauthenticated remote attacker can drive the server toward the
memory pressure that makes alloc_transport() fail by holding open
connections with large RFC1002 lengths up to MAX_STREAM_PROT_LEN
(0x00FFFFFF); natural transient allocation failures on a loaded
host produce the same drift more slowly.
Mirror the existing rollback pattern in ksmbd_kthread_fn(): on the
alloc_transport() failure path, decrement active_num_conn gated on
server_conf.max_connections.
Repro details: with the patch reverted, forced alloc_transport()
NULL returns leaked counter slots and subsequent connection
attempts -- including legitimate connects issued after the
forced-fail window had closed -- were all rejected with "Limit the
maximum number of connections". With this patch applied, the same
connect sequence produces no rejections and the counter cycles
cleanly between zero and one on every accept. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix out-of-bounds write in smb2_get_ea() EA alignment
smb2_get_ea() applies 4-byte alignment padding via memset() after
writing each EA entry. The bounds check on buf_free_len is performed
before the value memcpy, but the alignment memset fires unconditionally
afterward with no check on remaining space.
When the EA value exactly fills the remaining buffer (buf_free_len == 0
after value subtraction), the alignment memset writes 1-3 NUL bytes
past the buf_free_len boundary. In compound requests where the response
buffer is shared across commands, the first command (e.g., READ) can
consume most of the buffer, leaving a tight remainder for the QUERY_INFO
EA response. The alignment memset then overwrites past the physical
kvmalloc allocation into adjacent kernel heap memory.
Add a bounds check before the alignment memset to ensure buf_free_len
can accommodate the padding bytes.
This is the same bug pattern fixed by commit beef2634f81f ("ksmbd: fix
potencial OOB in get_file_all_info() for compound requests") and
commit fda9522ed6af ("ksmbd: fix OOB write in QUERY_INFO for compound
requests"), both of which added bounds checks before unconditional
writes in QUERY_INFO response handlers. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: use check_add_overflow() to prevent u16 DACL size overflow
set_posix_acl_entries_dacl() and set_ntacl_dacl() accumulate ACE sizes
in u16 variables. When a file has many POSIX ACL entries, the
accumulated size can wrap past 65535, causing the pointer arithmetic
(char *)pndace + *size to land within already-written ACEs. Subsequent
writes then overwrite earlier entries, and pndacl->size gets a
truncated value.
Use check_add_overflow() at each accumulation point to detect the
wrap before it corrupts the buffer, consistent with existing
check_mul_overflow() usage elsewhere in smbacl.c. |
| In the Linux kernel, the following vulnerability has been resolved:
net: altera-tse: fix skb leak on DMA mapping error in tse_start_xmit()
When dma_map_single() fails in tse_start_xmit(), the function returns
NETDEV_TX_OK without freeing the skb. Since NETDEV_TX_OK tells the
stack the packet was consumed, the skb is never freed, leaking memory
on every DMA mapping failure.
Add dev_kfree_skb_any() before returning to properly free the skb. |
| In the Linux kernel, the following vulnerability has been resolved:
mmc: vub300: fix NULL-deref on disconnect
Make sure to deregister the controller before dropping the reference to
the driver data on disconnect to avoid NULL-pointer dereferences or
use-after-free. |
| In the Linux kernel, the following vulnerability has been resolved:
nfc: llcp: add missing return after LLCP_CLOSED checks
In nfc_llcp_recv_hdlc() and nfc_llcp_recv_disc(), when the socket
state is LLCP_CLOSED, the code correctly calls release_sock() and
nfc_llcp_sock_put() but fails to return. Execution falls through to
the remainder of the function, which calls release_sock() and
nfc_llcp_sock_put() again. This results in a double release_sock()
and a refcount underflow via double nfc_llcp_sock_put(), leading to
a use-after-free.
Add the missing return statements after the LLCP_CLOSED branches
in both functions to prevent the fall-through. |
| In the Linux kernel, the following vulnerability has been resolved:
NFC: digital: Bounds check NFC-A cascade depth in SDD response handler
The NFC-A anti-collision cascade in digital_in_recv_sdd_res() appends 3
or 4 bytes to target->nfcid1 on each round, but the number of cascade
rounds is controlled entirely by the peer device. The peer sets the
cascade tag in the SDD_RES (deciding 3 vs 4 bytes) and the
cascade-incomplete bit in the SEL_RES (deciding whether another round
follows).
ISO 14443-3 limits NFC-A to three cascade levels and target->nfcid1 is
sized accordingly (NFC_NFCID1_MAXSIZE = 10), but nothing in the driver
actually enforces this. This means a malicious peer can keep the
cascade running, writing past the heap-allocated nfc_target with each
round.
Fix this by rejecting the response when the accumulated UID would exceed
the buffer.
Commit e329e71013c9 ("NFC: nci: Bounds check struct nfc_target arrays")
fixed similar missing checks against the same field on the NCI path. |
