| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ice: ice_adapter: release xa entry on adapter allocation failure
When ice_adapter_new() fails, the reserved XArray entry created by
xa_insert() is not released. This causes subsequent insertions at
the same index to return -EBUSY, potentially leading to
NULL pointer dereferences.
Reorder the operations as suggested by Przemek Kitszel:
1. Check if adapter already exists (xa_load)
2. Reserve the XArray slot (xa_reserve)
3. Allocate the adapter (ice_adapter_new)
4. Store the adapter (xa_store) |
| In the Linux kernel, the following vulnerability has been resolved:
x86/kvm: Force legacy PCI hole to UC when overriding MTRRs for TDX/SNP
When running as an SNP or TDX guest under KVM, force the legacy PCI hole,
i.e. memory between Top of Lower Usable DRAM and 4GiB, to be mapped as UC
via a forced variable MTRR range.
In most KVM-based setups, legacy devices such as the HPET and TPM are
enumerated via ACPI. ACPI enumeration includes a Memory32Fixed entry, and
optionally a SystemMemory descriptor for an OperationRegion, e.g. if the
device needs to be accessed via a Control Method.
If a SystemMemory entry is present, then the kernel's ACPI driver will
auto-ioremap the region so that it can be accessed at will. However, the
ACPI spec doesn't provide a way to enumerate the memory type of
SystemMemory regions, i.e. there's no way to tell software that a region
must be mapped as UC vs. WB, etc. As a result, Linux's ACPI driver always
maps SystemMemory regions using ioremap_cache(), i.e. as WB on x86.
The dedicated device drivers however, e.g. the HPET driver and TPM driver,
want to map their associated memory as UC or WC, as accessing PCI devices
using WB is unsupported.
On bare metal and non-CoCO, the conflicting requirements "work" as firmware
configures the PCI hole (and other device memory) to be UC in the MTRRs.
So even though the ACPI mappings request WB, they are forced to UC- in the
kernel's tracking due to the kernel properly handling the MTRR overrides,
and thus are compatible with the drivers' requested WC/UC-.
With force WB MTRRs on SNP and TDX guests, the ACPI mappings get their
requested WB if the ACPI mappings are established before the dedicated
driver code attempts to initialize the device. E.g. if acpi_init()
runs before the corresponding device driver is probed, ACPI's WB mapping
will "win", and result in the driver's ioremap() failing because the
existing WB mapping isn't compatible with the requested WC/UC-.
E.g. when a TPM is emulated by the hypervisor (ignoring the security
implications of relying on what is allegedly an untrusted entity to store
measurements), the TPM driver will request UC and fail:
[ 1.730459] ioremap error for 0xfed40000-0xfed45000, requested 0x2, got 0x0
[ 1.732780] tpm_tis MSFT0101:00: probe with driver tpm_tis failed with error -12
Note, the '0x2' and '0x0' values refer to "enum page_cache_mode", not x86's
memtypes (which frustratingly are an almost pure inversion; 2 == WB, 0 == UC).
E.g. tracing mapping requests for TPM TIS yields:
Mapping TPM TIS with req_type = 0
WARNING: CPU: 22 PID: 1 at arch/x86/mm/pat/memtype.c:530 memtype_reserve+0x2ab/0x460
Modules linked in:
CPU: 22 UID: 0 PID: 1 Comm: swapper/0 Tainted: G W 6.16.0-rc7+ #2 VOLUNTARY
Tainted: [W]=WARN
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/29/2025
RIP: 0010:memtype_reserve+0x2ab/0x460
__ioremap_caller+0x16d/0x3d0
ioremap_cache+0x17/0x30
x86_acpi_os_ioremap+0xe/0x20
acpi_os_map_iomem+0x1f3/0x240
acpi_os_map_memory+0xe/0x20
acpi_ex_system_memory_space_handler+0x273/0x440
acpi_ev_address_space_dispatch+0x176/0x4c0
acpi_ex_access_region+0x2ad/0x530
acpi_ex_field_datum_io+0xa2/0x4f0
acpi_ex_extract_from_field+0x296/0x3e0
acpi_ex_read_data_from_field+0xd1/0x460
acpi_ex_resolve_node_to_value+0x2ee/0x530
acpi_ex_resolve_to_value+0x1f2/0x540
acpi_ds_evaluate_name_path+0x11b/0x190
acpi_ds_exec_end_op+0x456/0x960
acpi_ps_parse_loop+0x27a/0xa50
acpi_ps_parse_aml+0x226/0x600
acpi_ps_execute_method+0x172/0x3e0
acpi_ns_evaluate+0x175/0x5f0
acpi_evaluate_object+0x213/0x490
acpi_evaluate_integer+0x6d/0x140
acpi_bus_get_status+0x93/0x150
acpi_add_single_object+0x43a/0x7c0
acpi_bus_check_add+0x149/0x3a0
acpi_bus_check_add_1+0x16/0x30
acpi_ns_walk_namespace+0x22c/0x360
acpi_walk_namespace+0x15c/0x170
acpi_bus_scan+0x1dd/0x200
acpi_scan_init+0xe5/0x2b0
acpi_init+0x264/0x5b0
do_one_i
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: verify orphan file size is not too big
In principle orphan file can be arbitrarily large. However orphan replay
needs to traverse it all and we also pin all its buffers in memory. Thus
filesystems with absurdly large orphan files can lead to big amounts of
memory consumed. Limit orphan file size to a sane value and also use
kvmalloc() for allocating array of block descriptor structures to avoid
large order allocations for sane but large orphan files. |
| In the Linux kernel, the following vulnerability has been resolved:
tls: wait for pending async decryptions if tls_strp_msg_hold fails
Async decryption calls tls_strp_msg_hold to create a clone of the
input skb to hold references to the memory it uses. If we fail to
allocate that clone, proceeding with async decryption can lead to
various issues (UAF on the skb, writing into userspace memory after
the recv() call has returned).
In this case, wait for all pending decryption requests. |
| In the Linux kernel, the following vulnerability has been resolved:
x86/mm: Fix SMP ordering in switch_mm_irqs_off()
Stephen noted that it is possible to not have an smp_mb() between
the loaded_mm store and the tlb_gen load in switch_mm(), meaning the
ordering against flush_tlb_mm_range() goes out the window, and it
becomes possible for switch_mm() to not observe a recent tlb_gen
update and fail to flush the TLBs.
[ dhansen: merge conflict fixed by Ingo ] |
| In the Linux kernel, the following vulnerability has been resolved:
net/ip6_tunnel: Prevent perpetual tunnel growth
Similarly to ipv4 tunnel, ipv6 version updates dev->needed_headroom, too.
While ipv4 tunnel headroom adjustment growth was limited in
commit 5ae1e9922bbd ("net: ip_tunnel: prevent perpetual headroom growth"),
ipv6 tunnel yet increases the headroom without any ceiling.
Reflect ipv4 tunnel headroom adjustment limit on ipv6 version.
Credits to Francesco Ruggeri, who was originally debugging this issue
and wrote local Arista-specific patch and a reproducer. |
| In the Linux kernel, the following vulnerability has been resolved:
smc: Use __sk_dst_get() and dst_dev_rcu() in smc_clc_prfx_match().
smc_clc_prfx_match() is called from smc_listen_work() and
not under RCU nor RTNL.
Using sk_dst_get(sk)->dev could trigger UAF.
Let's use __sk_dst_get() and dst_dev_rcu().
Note that the returned value of smc_clc_prfx_match() is not
used in the caller. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/guc: Check GuC running state before deregistering exec queue
In normal operation, a registered exec queue is disabled and
deregistered through the GuC, and freed only after the GuC confirms
completion. However, if the driver is forced to unbind while the exec
queue is still running, the user may call exec_destroy() after the GuC
has already been stopped and CT communication disabled.
In this case, the driver cannot receive a response from the GuC,
preventing proper cleanup of exec queue resources. Fix this by directly
releasing the resources when GuC is not running.
Here is the failure dmesg log:
"
[ 468.089581] ---[ end trace 0000000000000000 ]---
[ 468.089608] pci 0000:03:00.0: [drm] *ERROR* GT0: GUC ID manager unclean (1/65535)
[ 468.090558] pci 0000:03:00.0: [drm] GT0: total 65535
[ 468.090562] pci 0000:03:00.0: [drm] GT0: used 1
[ 468.090564] pci 0000:03:00.0: [drm] GT0: range 1..1 (1)
[ 468.092716] ------------[ cut here ]------------
[ 468.092719] WARNING: CPU: 14 PID: 4775 at drivers/gpu/drm/xe/xe_ttm_vram_mgr.c:298 ttm_vram_mgr_fini+0xf8/0x130 [xe]
"
v2: use xe_uc_fw_is_running() instead of xe_guc_ct_enabled().
As CT may go down and come back during VF migration.
(cherry picked from commit 9b42321a02c50a12b2beb6ae9469606257fbecea) |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: use RCU in ip6_output()
Use RCU in ip6_output() in order to use dst_dev_rcu() to prevent
possible UAF.
We can remove rcu_read_lock()/rcu_read_unlock() pairs
from ip6_finish_output2(). |
| In the Linux kernel, the following vulnerability has been resolved:
EDAC/i10nm: Skip DIMM enumeration on a disabled memory controller
When loading the i10nm_edac driver on some Intel Granite Rapids servers,
a call trace may appear as follows:
UBSAN: shift-out-of-bounds in drivers/edac/skx_common.c:453:16
shift exponent -66 is negative
...
__ubsan_handle_shift_out_of_bounds+0x1e3/0x390
skx_get_dimm_info.cold+0x47/0xd40 [skx_edac_common]
i10nm_get_dimm_config+0x23e/0x390 [i10nm_edac]
skx_register_mci+0x159/0x220 [skx_edac_common]
i10nm_init+0xcb0/0x1ff0 [i10nm_edac]
...
This occurs because some BIOS may disable a memory controller if there
aren't any memory DIMMs populated on this memory controller. The DIMMMTR
register of this disabled memory controller contains the invalid value
~0, resulting in the call trace above.
Fix this call trace by skipping DIMM enumeration on a disabled memory
controller. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/vt-d: debugfs: Fix legacy mode page table dump logic
In legacy mode, SSPTPTR is ignored if TT is not 00b or 01b. SSPTPTR
maybe uninitialized or zero in that case and may cause oops like:
Oops: general protection fault, probably for non-canonical address
0xf00087d3f000f000: 0000 [#1] SMP NOPTI
CPU: 2 UID: 0 PID: 786 Comm: cat Not tainted 6.16.0 #191 PREEMPT(voluntary)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.17.0-5.fc42 04/01/2014
RIP: 0010:pgtable_walk_level+0x98/0x150
RSP: 0018:ffffc90000f279c0 EFLAGS: 00010206
RAX: 0000000040000000 RBX: ffffc90000f27ab0 RCX: 000000000000001e
RDX: 0000000000000003 RSI: f00087d3f000f000 RDI: f00087d3f0010000
RBP: ffffc90000f27a00 R08: ffffc90000f27a98 R09: 0000000000000002
R10: 0000000000000000 R11: 0000000000000000 R12: f00087d3f000f000
R13: 0000000000000000 R14: 0000000040000000 R15: ffffc90000f27a98
FS: 0000764566dcb740(0000) GS:ffff8881f812c000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000764566d44000 CR3: 0000000109d81003 CR4: 0000000000772ef0
PKRU: 55555554
Call Trace:
<TASK>
pgtable_walk_level+0x88/0x150
domain_translation_struct_show.isra.0+0x2d9/0x300
dev_domain_translation_struct_show+0x20/0x40
seq_read_iter+0x12d/0x490
...
Avoid walking the page table if TT is not 00b or 01b. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: Intel: bytcr_rt5640: Fix invalid quirk input mapping
When an invalid value is passed via quirk option, currently
bytcr_rt5640 driver only shows an error message but leaves as is.
This may lead to unepxected results like OOB access.
This patch corrects the input mapping to the certain default value if
an invalid value is passed. |
| In the Linux kernel, the following vulnerability has been resolved:
mm: hugetlb: avoid soft lockup when mprotect to large memory area
When calling mprotect() to a large hugetlb memory area in our customer's
workload (~300GB hugetlb memory), soft lockup was observed:
watchdog: BUG: soft lockup - CPU#98 stuck for 23s! [t2_new_sysv:126916]
CPU: 98 PID: 126916 Comm: t2_new_sysv Kdump: loaded Not tainted 6.17-rc7
Hardware name: GIGACOMPUTING R2A3-T40-AAV1/Jefferson CIO, BIOS 5.4.4.1 07/15/2025
pstate: 20400009 (nzCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : mte_clear_page_tags+0x14/0x24
lr : mte_sync_tags+0x1c0/0x240
sp : ffff80003150bb80
x29: ffff80003150bb80 x28: ffff00739e9705a8 x27: 0000ffd2d6a00000
x26: 0000ff8e4bc00000 x25: 00e80046cde00f45 x24: 0000000000022458
x23: 0000000000000000 x22: 0000000000000004 x21: 000000011b380000
x20: ffff000000000000 x19: 000000011b379f40 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000
x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000
x11: 0000000000000000 x10: 0000000000000000 x9 : ffffc875e0aa5e2c
x8 : 0000000000000000 x7 : 0000000000000000 x6 : 0000000000000000
x5 : fffffc01ce7a5c00 x4 : 00000000046cde00 x3 : fffffc0000000000
x2 : 0000000000000004 x1 : 0000000000000040 x0 : ffff0046cde7c000
Call trace:
mte_clear_page_tags+0x14/0x24
set_huge_pte_at+0x25c/0x280
hugetlb_change_protection+0x220/0x430
change_protection+0x5c/0x8c
mprotect_fixup+0x10c/0x294
do_mprotect_pkey.constprop.0+0x2e0/0x3d4
__arm64_sys_mprotect+0x24/0x44
invoke_syscall+0x50/0x160
el0_svc_common+0x48/0x144
do_el0_svc+0x30/0xe0
el0_svc+0x30/0xf0
el0t_64_sync_handler+0xc4/0x148
el0t_64_sync+0x1a4/0x1a8
Soft lockup is not triggered with THP or base page because there is
cond_resched() called for each PMD size.
Although the soft lockup was triggered by MTE, it should be not MTE
specific. The other processing which takes long time in the loop may
trigger soft lockup too.
So add cond_resched() for hugetlb to avoid soft lockup. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: pcm: Disable bottom softirqs as part of spin_lock_irq() on PREEMPT_RT
snd_pcm_group_lock_irq() acquires a spinlock_t and disables interrupts
via spin_lock_irq(). This also implicitly disables the handling of
softirqs such as TIMER_SOFTIRQ.
On PREEMPT_RT softirqs are preemptible and spin_lock_irq() does not
disable them. That means a timer can be invoked during spin_lock_irq()
on the same CPU. Due to synchronisations reasons local_bh_disable() has
a per-CPU lock named softirq_ctrl.lock which synchronizes individual
softirq against each other.
syz-bot managed to trigger a lockdep report where softirq_ctrl.lock is
acquired in hrtimer_cancel() in addition to hrtimer_run_softirq(). This
is a possible deadlock.
The softirq_ctrl.lock can not be made part of spin_lock_irq() as this
would lead to too much synchronisation against individual threads on the
system. To avoid the possible deadlock, softirqs must be manually
disabled before the lock is acquired.
Disable softirqs before the lock is acquired on PREEMPT_RT. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: ISO: Fix possible UAF on iso_conn_free
This attempt to fix similar issue to sco_conn_free where if the
conn->sk is not set to NULL may lead to UAF on iso_conn_free. |
| In the Linux kernel, the following vulnerability has been resolved:
net: usb: Remove disruptive netif_wake_queue in rtl8150_set_multicast
syzbot reported WARNING in rtl8150_start_xmit/usb_submit_urb.
This is the sequence of events that leads to the warning:
rtl8150_start_xmit() {
netif_stop_queue();
usb_submit_urb(dev->tx_urb);
}
rtl8150_set_multicast() {
netif_stop_queue();
netif_wake_queue(); <-- wakes up TX queue before URB is done
}
rtl8150_start_xmit() {
netif_stop_queue();
usb_submit_urb(dev->tx_urb); <-- double submission
}
rtl8150_set_multicast being the ndo_set_rx_mode callback should not be
calling netif_stop_queue and notif_start_queue as these handle
TX queue synchronization.
The net core function dev_set_rx_mode handles the synchronization
for rtl8150_set_multicast making it safe to remove these locks. |
| In the Linux kernel, the following vulnerability has been resolved:
smc: Use __sk_dst_get() and dst_dev_rcu() in in smc_clc_prfx_set().
smc_clc_prfx_set() is called during connect() and not under RCU
nor RTNL.
Using sk_dst_get(sk)->dev could trigger UAF.
Let's use __sk_dst_get() and dev_dst_rcu() under rcu_read_lock()
after kernel_getsockname().
Note that the returned value of smc_clc_prfx_set() is not used
in the caller.
While at it, we change the 1st arg of smc_clc_prfx_set[46]_rcu()
not to touch dst there. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: use RCU in ip6_xmit()
Use RCU in ip6_xmit() in order to use dst_dev_rcu() to prevent
possible UAF. |
| In the Linux kernel, the following vulnerability has been resolved:
dm: fix NULL pointer dereference in __dm_suspend()
There is a race condition between dm device suspend and table load that
can lead to null pointer dereference. The issue occurs when suspend is
invoked before table load completes:
BUG: kernel NULL pointer dereference, address: 0000000000000054
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 6 PID: 6798 Comm: dmsetup Not tainted 6.6.0-g7e52f5f0ca9b #62
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.1-2.fc37 04/01/2014
RIP: 0010:blk_mq_wait_quiesce_done+0x0/0x50
Call Trace:
<TASK>
blk_mq_quiesce_queue+0x2c/0x50
dm_stop_queue+0xd/0x20
__dm_suspend+0x130/0x330
dm_suspend+0x11a/0x180
dev_suspend+0x27e/0x560
ctl_ioctl+0x4cf/0x850
dm_ctl_ioctl+0xd/0x20
vfs_ioctl+0x1d/0x50
__se_sys_ioctl+0x9b/0xc0
__x64_sys_ioctl+0x19/0x30
x64_sys_call+0x2c4a/0x4620
do_syscall_64+0x9e/0x1b0
The issue can be triggered as below:
T1 T2
dm_suspend table_load
__dm_suspend dm_setup_md_queue
dm_mq_init_request_queue
blk_mq_init_allocated_queue
=> q->mq_ops = set->ops; (1)
dm_stop_queue / dm_wait_for_completion
=> q->tag_set NULL pointer! (2)
=> q->tag_set = set; (3)
Fix this by checking if a valid table (map) exists before performing
request-based suspend and waiting for target I/O. When map is NULL,
skip these table-dependent suspend steps.
Even when map is NULL, no I/O can reach any target because there is
no table loaded; I/O submitted in this state will fail early in the
DM layer. Skipping the table-dependent suspend logic in this case
is safe and avoids NULL pointer dereferences. |
| In the Linux kernel, the following vulnerability has been resolved:
mptcp: Use __sk_dst_get() and dst_dev_rcu() in mptcp_active_enable().
mptcp_active_enable() is called from subflow_finish_connect(),
which is icsk->icsk_af_ops->sk_rx_dst_set() and it's not always
under RCU.
Using sk_dst_get(sk)->dev could trigger UAF.
Let's use __sk_dst_get() and dst_dev_rcu(). |
