| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
cxgb4/ch_ktls: disable softirqs around tid_list erases
chcr_ktls_cpl_act_open_rpl() inserts into tid_list from the receive path
using xa_insert_bh(). The array is shared by the adapter's connections
and initialized with XA_FLAGS_LOCK_BH. However, chcr_ktls_dev_del() and
the chcr_ktls_dev_add() error path use xa_erase(), which takes the XArray
lock without disabling softirqs.
When cleanup runs with softirqs enabled, a receive softirq for another
connection on the same CPU can interrupt the erase and spin on the lock
held by the interrupted task. Use xa_erase_bh() at both sites to match
the insertion path. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: tcpm: recover after failure to start the frs ams
Reset the port if the tcpm fails to start the FAST_ROLE_SWAP AMS by
initiating error recovery on it.
This helps in cases where some cables (incorrectly) signal an FRS to
an FRS capable port during disconnection. The TCPC autonomously starts
sourcing VBUS on detecting the FRS signal. However, the VBUS sourcing is
left on when the FAST_ROLE_SWAP AMS fails to start (as tcpm_sink_tx_ok
is 0 as CC is open due to the cable disconnect). This is because the
code sets the state to INVALID_STATE without resetting the port state.
Log snippet before changes:
[ 101.401960] AMS FAST_ROLE_SWAP start
[ 101.401971] Sink TX No Go
[ 101.401982] sourcing vbus
[ 101.401987] VBUS on
[ 101.402159] VBUS on
[ 109.257809] CC1: 0 -> 0, CC2: 5 -> 0 [state SNK_READY, polarity 1, disconnected]
[ 111.267442] VBUS on
After changes:
[ 70.541211] AMS FAST_ROLE_SWAP start
[ 70.541220] Sink TX No Go
[ 70.541228] state change SNK_READY -> ERROR_RECOVERY [rev3 NONE_AMS]
[ 70.541362] VBUS on
[ 70.541365] sourcing vbus
[ 70.541367] VBUS on
[ 70.541374] state change ERROR_RECOVERY -> PORT_RESET [rev3 NONE_AMS]
[ 70.541410] disable vbus discharge ret:0
[ 70.543028] Setting usb_comm capable false
[ 70.544009] Setting voltage/current limit 0 mV 0 mA
[ 70.544034] polarity 0
[ 70.544239] Requesting mux state 0, usb-role 0, orientation 0
[ 70.555550] cc:=0
[ 70.555595] pending state change PORT_RESET -> PORT_RESET_WAIT_OFF @ 100 ms [rev3 NONE_AMS]
[ 70.555697] VBUS off
[ 70.555702] VBUS VSAFE0V
[ 70.555762] CC1: 5 -> 0, CC2: 0 -> 0 [state PORT_RESET, polarity 0, disconnected]
[ 70.587794] VBUS off
[ 70.587799] VBUS VSAFE0V
[ 70.655672] state change PORT_RESET -> PORT_RESET_WAIT_OFF [delayed 100 ms]
[ 70.655682] state change PORT_RESET_WAIT_OFF -> SNK_UNATTACHED [rev3 NONE_AMS]
[ 70.655686] Start toggling
[ 70.656274] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected] |
| In the Linux kernel, the following vulnerability has been resolved:
usb: core: clear both ep_in and ep_out for non-ep0 control endpoints
In usb_enable_endpoint(), non-zero control endpoints (where
usb_endpoint_xfer_control(&ep->desc) is true) populate both
dev->ep_in[epnum] and dev->ep_out[epnum] with the same struct
usb_host_endpoint pointer.
However, usb_disable_endpoint() only clears either dev->ep_out[epnum] or
dev->ep_in[epnum] depending on the direction bit of epaddr when
reset_hardware is set, leaving the opposite direction's array slot
pointing to the disabled/freed endpoint.
Clear both dev->ep_out[epnum] and dev->ep_in[epnum] when disabling a
non-ep0 control endpoint with reset_hardware set, and update the
function kerneldoc accordingly.
Tested in QEMU against Linux 7.3.0-rc3 using dummy_hcd and raw-gadget to
enumerate a USB device with a non-zero control endpoint
(bEndpointAddress 0x01, bmAttributes USB_ENDPOINT_XFER_CONTROL),
verifying that both dev->ep_in[1] and dev->ep_out[1] are cleared when
the interface is disabled. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: dwc3: gadget: fix IRQ storm on invalid event buffer count
When dwc3_check_event_buf() reads a GEVNTCOUNT value exceeding the
event buffer length, commit 63ccd26cd1f6 ("usb: dwc3: gadget: check
that event count does not exceed event buffer length") returns IRQ_NONE
without writing back GEVNTCOUNT. Since the DWC3 interrupt is
level-triggered, the uncleared IRQ source keeps the line asserted,
causing a tight IRQ storm that accumulates 99,900 unhandled interrupts
and triggers spurious.c:184 BUG -> kernel panic.
The resulting call stack:
__report_bad_irq+0xac/0xc8
note_interrupt+0x340/0x468
handle_irq_event+0xac/0xc0
handle_fasteoi_irq+0x120/0x228
gic_handle_irq+0x68/0x108
...
kernel BUG at kernel/irq/spurious.c:184
To reproduce, write a bogus value exceeding the event buffer length
directly to the GEVNTCOUNT register:
devmem <DWC3_BASE + 0xc40c> 4 0x1004
Write the bogus count back to GEVNTCOUNT to clear the IRQ source,
consistent with the stale event clearing pattern in
dwc3_event_buffers_setup(), and schedule error recovery to
reinitialize the controller. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/i2c: cancel the client work on remove
xe_i2c_notifier() stores the DesignWare adapter in i2c->adapter and
schedules i2c->work when the adapter is registered under the xe I2C
platform device, and xe_i2c_client_work() then instantiates the AMC
client device on that adapter.
xe_i2c_remove() tears down the AMC, unregisters the client devices,
the bus notifier and the adapter platform device, but it never drains
i2c->work. A work item that is still queued or running when the
adapter is unregistered dereferences i2c->adapter in
i2c_new_client_device() after platform_device_unregister() has
released the adapter. The work item is also embedded in the
devm-allocated struct xe_i2c, so a work item still queued after the
drm device devm unwind frees that allocation runs its callback on
freed memory.
The bus notifier is the only thing that schedules this work, and it is
unregistered after the client devices. An instance that is still queued
when the teardown runs can therefore write
i2c->client[XE_I2C_CLIENT_AMC] while the loop is unregistering and
clearing the same array, and an AMC client it instantiates late is only
cleaned up by the adapter's own child sweep in i2c_del_adapter().
Move bus_unregister_notifier() in front of the client teardown loop
and cancel the work right after it, so no new instance can be
scheduled and a queued instance is drained before the client array is
touched. A running instance still finds a live adapter, since the
adapter is unregistered later.
(cherry picked from commit a23f27d5ec11c3f418c5e5531eea34ccda2b5b20) |
| In the Linux kernel, the following vulnerability has been resolved:
nvme-multipath: set BLK_FEAT_ZONED only after the zone info is known
The namespace head is marked zoned at allocation time based only on the
command set identifier. If the zone info query reports a zero zone size,
the path namespace is registered without zoned limits while the head
still advertises the zoned capability with a zone size of zero, and
reporting zones or writing to the head then shifts by ilog2(0).
Drop the zoned feature from the head allocation and let the head limits
refresh stack it in from the path namespace instead. |
| In the Linux kernel, the following vulnerability has been resolved:
tpm: fix off-by-four bounds check in tpm2_get_random()
When the response carries the TPM2_ST_SESSIONS tag, tpm2_get_random()
skips the 4-byte parameter size field before locating the random data,
but the bounds check still validates the response length against
TPM_HEADER_SIZE. A truncated response can pass the check and make
memcpy() read up to 4 bytes past the response end, so stale buffer
contents end up in the caller's random bytes.
Fix this by checking the response length against 'offset', which
already includes the skipped parameter size field. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/i915/gt: Unmask interrupts only when ACTIVE is true
There is a small race window between intel_rps_boost() reading
a stale ACTIVE state and queuing rps->work, where ACTIVE may be
changed via asynchronous calls triggered by wakeref drop.
This means that rps_work() could be triggered after the GT has
been parked, so unmasking RPS PM interrupts would happen without
holding PM wakelock. This sequence of events may be observed
during live_rc6_ctx_wa() selftest:
1) live_rc6_ctx_wa()
-> intel_engine_pm_put()
-> wakeref_put()
ASYNC1) wakeref_put() callback
-> __engine_park()
-> intel_gt_pm_put_async()
-> intel_gt_pm_put_async_untracked()
-> intel_wakeref_put_async()
ASYNC2) wakeref_put_async() callback
-> __gt_park()
-> intel_rps_park()
-> intel_rps_clear_active() [clear ACTIVE]
WITH INTERRUPTS:
-> rps_disable_interrupts()
-> cancel_work_sync(rps->work)
-> rps_reset_interrupts() [rps->pm_iir = 0]
WITHOUT INTERRUPTS (TIMER mode):
-> rps_stop_timer()
-> cancel_work_sync(rps->work)
2) live_rc6_ctx_wa()
-> intel_gt_wait_for_idle()
-> intel_gt_retire_requests_timeout()
-> dma_fence_wait_timeout()
-> ops->wait() [i915_fence_wait()]
-> i915_request_wait_timeout()
-> intel_rps_boost()
-> intel_rps_is_active() [check ACTIVE]
[OPEN RACE WINDOW]
-> queue_work(rps->work)
-> retire_requests()
-> i915_request_retire()
-> intel_rps_dec_waiters() [from 1 to 0]
If ASYNC1 and ASYNC2 would execute during [OPEN RACE WINDOW],
then:
3) rps_work() executes from the workqueue and may satisfy
"(!pm_iir && !client_boost)" test (in TIMER mode rps->pm_iir
is zeroed by an earlier rps_work() call or never gets a new
value after previous intel_rps_unpark() event), so it jumps
to "out" label, bypassing intel_rps_is_active() guard and
executes gen6_gt_pm_unmask_irq();
4) GT is parked and runtime PM wakelock is dropped, so only
a raw reference in __gt_park() ->
intel_display_power_put_async() remains for 100ms, then the
MMIO write in gen6_gt_pm_unmask_irq() detects missing
wakelock via assert_rpm_wakelock_held() and emits
"RPM wakelock ref not held during HW access" tainting kernel.
Commit 3e7abf814193 ("drm/i915: Extract GT render power state management")
dropped the "if (rps->interrupts_enabled)" guard that
gen6_pm_rps_work() had around this unmask in i915_irq.c.
INTEL_RPS_ACTIVE brackets the same window, since it is set in
intel_rps_unpark() before rps_enable_interrupts() and
rps_start_timer() and cleared in intel_rps_park() before
rps_stop_timer() and rps_disable_interrupts().
Skip unmasking when RPS is no longer active (reaching unmask
operation is independent of INTERRUPT mode). This does not
prevent RPS operation from resuming on the next unpark.
In interrupt mode, intel_rps_unpark() calls
rps_enable_interrupts(), which enables and unmasks the PM
interrupts. In timer mode, it calls rps_start_timer(),
restarting periodic engine-busyness evaluation. The timer
generates software RPS events and queues rps_work() directly,
independently of PM interrupt delivery. Neither mode requires
the late worker to unmask interrupts while the GT is parked
(cherry picked from commit ca4a6deadad15b91ee083afe445fa6bdbfb68206) |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: RFCOMM: Fix NULL tty_dev dereference in rfcomm_dev_shutdown
syzbot hit a NULL pointer dereference in rfcomm_dev_shutdown() when an
RFCOMM tty is closed.
rfcomm_dev_add() puts the new device on rfcomm_dev_list first and only
then registers the tty device and saves it in dev->tty_dev. If that
registration fails, dev->tty_dev is never set at all. The device can be
looked up in the meantime, so an open() of /dev/rfcommN gets through
rfcomm_tty_install() and attaches to it. When that tty is closed again,
rfcomm_dev_shutdown() uses dev->tty_dev without checking it:
Oops: general protection fault, probably for non-canonical address
KASAN: null-ptr-deref in range [0x0000000000000040-0x0000000000000047]
RIP: 0010:rfcomm_dev_shutdown+0x48/0xb0 net/bluetooth/rfcomm/tty.c:131
Call Trace:
tty_port_shutdown+0x1bf/0x220 drivers/tty/tty_port.c:372
tty_port_close+0x4e/0x150 drivers/tty/tty_port.c:705
tty_release+0x359/0x1670 drivers/tty/tty_io.c:1718
__fput+0x418/0xa50 fs/file_table.c:512
rfcomm_dev_destruct() already copes with a NULL dev->tty_dev. Add the
same check to rfcomm_dev_shutdown(), so the tty device is only moved
when it was actually registered. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sock: Serialize dead-device detachment
Rebinding an HCI socket after its controller is unregistered can race
monitor control replay and crash the kernel. hci_sock_bind() clears
hci_pi(sk)->hdev and drops the device reference under only the socket
lock, whereas send_monitor_control_replay() holds hci_sk_list.lock for
reading.
Replay can observe a non-NULL hdev, then bind can clear it and drop the
last reference before create_monitor_ctrl_open() reads hdev->id. This
can cause a NULL pointer dereference if the pointer is reloaded, or a
use-after-free if the old pointer is retained.
The kernel reported:
KASAN: null-ptr-deref in range [0x0000000000000068-0x000000000000006f]
RIP: 0010:create_monitor_ctrl_open+0x579/0x800
Call Trace:
hci_sock_bind+0xd96/0x1190
__sys_bind+0x166/0x200
__x64_sys_bind+0x6d/0xb0
do_syscall_64+0xdd/0x4a0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
The same missing serialization lets hci_send_to_sock() select a socket
for the old device and queue its frame after bind has detached the socket
or installed a new binding.
Take hci_sk_list.lock for writing when clearing the device pointer and
resetting the socket state. This waits for existing replay and delivery
readers to finish before detachment and prevents later readers from
using the old binding. Keep hci_dev_put() outside the critical section
because the final device release can sleep. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_core: Serialize ACL scheduling with channel deletion
hci_chan_sent() selects a channel under RCU but drops the read lock before
accessing chan->conn and returning the channel. The ACL and LE schedulers
then use its packet queue and update its transmit counters without any
protection against channel deletion.
After TX selects a channel and releases RCU, a disconnect command timeout
on the separate request workqueue can run hci_conn_failed() and
l2cap_conn_del(). hci_chan_del() can then unlink the channel, complete
synchronize_rcu(), purge its queue and free it before TX resumes. This
causes use-after-free both in hci_chan_sent() and in its callers.
KASAN reported:
BUG: KASAN: slab-use-after-free in hci_chan_sent+0x892/0x9b0
Workqueue: hci0 hci_tx_work
Call Trace:
hci_chan_sent+0x892/0x9b0
hci_tx_work+0x5e6/0xb70
Allocated by task 91:
hci_chan_create+0xe3/0x350
l2cap_conn_add.part.0+0x12/0xa30
l2cap_chan_connect+0x110d/0x1b60
l2cap_sock_connect+0x310/0x530
Freed by task 99:
hci_chan_del+0x11f/0x170
l2cap_conn_del+0x4f1/0x800
l2cap_connect_cfm+0x88c/0xd30
hci_conn_failed+0x150/0x250
hci_abort_conn_sync+0x3e3/0x800
hci_cmd_sync_run+0x7e/0xc0
hci_abort_conn+0x105/0x1f0
disconnect_sync+0x157/0x290
hci_cmd_sync_work+0x13c/0x290
Hold the existing device mutex across channel selection and transmission
in both schedulers to serialize them with channel teardown. Keep timeout
handling outside the critical sections because hci_link_tx_to() acquires
the same mutex. This also permits the transmit path to sleep, unlike
extending the RCU read-side critical section across packet submission. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: tipd: fix uninitialized typec_partner_desc in cd321x_update_work()
cd321x_update_work() passes a stack-allocated typec_partner_desc to
typec_register_partner() after initializing only usb_pd, accessory and
identity.
typec_register_partner() copies attach and deattach from the descriptor
into the partner. With those fields left unset, garbage function pointers
may be stored and later invoked from typec_partner_link_device() when a USB
device is linked to the port. Uninitialized pd_revision and usb_capability
similarly leak stack data through partner sysfs.
Zero-initialize the descriptor so optional callbacks remain NULL and the
remaining fields are zero. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: fix port tear down use-after-free
Some drivers for multiport devices access port driver data from
completion handlers of shared URBs submitted at attach() or first open()
and stopped at disconnect() or last close(), respectively.
A simple NULL check before accessing the driver data makes sure that a
port state container has at least been allocated, but a completion
handler can still race with port tear down.
Reorder the disconnect handling so that ports are not deregistered (and
their driver data freed) until after all ports have been hung up and the
driver disconnect() callback has run so that all I/O has been stopped. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: restore active device pointers after failed sprout
btrfs_init_new_device() switches latest_dev and possibly s_bdev from the
seed device to the new sprout device before creating the first writable
chunks.
If chunk creation or the subsequent sprout setup fails, the error path
releases the new device without switching those pointers back.
btrfs_show_devname() can then dereference the freed latest_dev and crash.
Restore the active device pointers to the latest seed device before
removing and releasing the failed sprout device. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: detach failed sprout device from transaction update list
When creating the first metadata chunk for a sprout filesystem,
create_chunk() adds the new device to the transaction dev_update_list
through device->post_commit_list.
If the subsequent system chunk creation fails, btrfs_init_new_device()
aborts the transaction and releases the device while post_commit_list is
still linked. This triggers a warning in btrfs_free_device() and leaves
the transaction list referencing freed memory.
Detach the device while holding chunk_mutex before releasing it. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: amd: yc: fix memory leak in acp6x_pdm_dma_close()
acp6x_pdm_dma_close() does not free the runtime->private_data buffer
allocated in acp6x_pdm_dma_open(). Add the missing kfree. |
| In the Linux kernel, the following vulnerability has been resolved:
netfs: Fix missing alloc tagging of direct mempool allocations
Commit 1d78d56c43ef ("netfs: Fix folio_queue ENOMEM in writeback by
adding a mempool") added a mempool for the folio_queues and made the
request, subrequest and folio_queue allocations distinguish between
writeback and everything else. Writeback is part of memory reclaim
and must not fail due to ENOMEM, so it allocates under GFP_NOFS
through mempool_alloc(), which may dip into the pool's reserve and,
if that runs empty, wait for elements to be returned. The
GFP_KERNEL paths, which can return -ENOMEM to their callers, invoke
the pool's ->alloc() callback directly instead.
The direct call, however, skips the alloc_hooks() wrapper that the
mempool_alloc() macro provides. The pool callbacks, mempool_alloc_slab()
and mempool_kmalloc(), call kmem_cache_alloc_noprof() and kmalloc_noprof()
and rely on current->alloc_tag having been set by the caller. With
CONFIG_MEM_ALLOC_PROFILING_DEBUG=y this leads to
current->alloc_tag not set
WARNING: ./include/linux/alloc_tag.h:161 at __alloc_tagging_slab_alloc_hook
alloc_tag was not set
WARNING: ./include/linux/alloc_tag.h:166 at __alloc_tagging_slab_free_hook
at allocation and free time respectively, as reported when reading
files on a CIFS mount. The allocations are also missing from
/proc/allocinfo.
Wrap the direct ->alloc() invocations in alloc_hooks() with a new
mempool_alloc_noreserve() helper in include/linux/mempool.h, next to
the other alloc_hooks()-wrapped macros such as mempool_alloc(). The
GFP_KERNEL paths keep their failable allocation semantics, they just
get tagged now. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: gadget: dummy-hcd: Fix wait for outstanding request completions
The dummy-hcd driver emulates synchronize_irq() by waiting until its
private callback_usage counter drops to 0 (with the private lock not
held). This counter is incremented whenever a gadget driver callback
occurs (which requires the private lock to be dropped), but not when a
request completion handler is called.
This is an oversight. Request completion is triggered by timer
interrupts (emulating device IRQs in a real UDC), and the interrupt
handlers are supposed to have completed when the synchronize_irq()
emulation routine returns -- they aren't supposed to be in the middle
of a completion callback. If this happens it can lead to a gadget
driver's unbind routine running before all outstanding request
completions have finished, maybe even allowing the gadget driver's
module to be unloaded while a completion handler is still running.
Fix the oversight by incrementing the callback_usage value across
request completion callbacks. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: aspeed-vhub: cancel wake work on device removal
wake_work is armed from the gadget .wakeup callback to resume suspended
downstream ports, and it is never cancelled in ast_vhub_remove(), so a
work item queued before or during removal can run after devm has freed
vhub and its ports, a use-after-free.
Cancelling the work alone is not sufficient: usb_gadget_wakeup() takes
no lock and the unbind path never clears wakeup_en, so a remote-wakeup
request in flight on another CPU can re-arm the work after the cancel
and before vhub is freed.
ast_vhub_del_dev() already clears d->registered under vhub->lock before
unregistering the gadget. Refuse the wakeup in ast_vhub_udc_wakeup()
once d->registered is clear: the check and the schedule_work() are then
atomic against the unbind, so a wakeup that passed before the flag was
cleared is drained by the cancel_work_sync() after the del_dev loop,
and one that arrives later returns without arming. Also move INIT_WORK()
to the top of ast_vhub_probe(), since the probe error path reuses
ast_vhub_remove() and would otherwise cancel a never-initialized work
item.
This issue was found by an in-house static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_uac1_legacy: validate bRequest index in generic_{set,get}_cmd
generic_set_cmd() and generic_get_cmd() use the low nibble of
ctrl->bRequest as an index into con->data[]:
u8 cmd = (ctrl->bRequest & 0x0F); /* 0 .. 15 */
...
con->data[cmd] = value; /* OOB when cmd >= 5 */
struct usb_audio_control (include/linux/usb/audio.h) declares data as
a 5-element array, so indices 5 through 15 write (or read) up to 44
bytes past the end of the array on the heap.
A malicious USB host can craft a class-specific SET_CUR / GET_CUR
request with an arbitrary bRequest value, triggering the out-of-bounds
access from an IRQ completion handler with no further preconditions.
Add an ARRAY_SIZE() guard to both functions. |
