| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
nvme: apple: fix device reference counting
Drivers must call nvme_uninit_ctrl after a successful nvme_init_ctrl.
Split the allocation side out to make the error handling boundary easier
to navigate. The apple driver had been doing this wrong, leaking the
controller device memory on a tagset failure. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath12k: change DMA direction while mapping reinjected packets
For fragmented packets, ath12k reassembles each fragment as a normal
packet and then reinjects it into HW ring. In this case, the DMA
direction should be DMA_TO_DEVICE, not DMA_FROM_DEVICE. Otherwise,
an invalid payload may be reinjected into the HW and
subsequently delivered to the host.
Given that arbitrary memory can be allocated to the skb buffer,
knowledge about the data contained in the reinjected buffer is lacking.
Consequently, there’s a risk of private information being leaked.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00209-QCAHKSWPL_SILICONZ-1 |
| In the Linux kernel, the following vulnerability has been resolved:
mlxsw: spectrum_acl_erp: Fix object nesting warning
ACLs in Spectrum-2 and newer ASICs can reside in the algorithmic TCAM
(A-TCAM) or in the ordinary circuit TCAM (C-TCAM). The former can
contain more ACLs (i.e., tc filters), but the number of masks in each
region (i.e., tc chain) is limited.
In order to mitigate the effects of the above limitation, the device
allows filters to share a single mask if their masks only differ in up
to 8 consecutive bits. For example, dst_ip/25 can be represented using
dst_ip/24 with a delta of 1 bit. The C-TCAM does not have a limit on the
number of masks being used (and therefore does not support mask
aggregation), but can contain a limited number of filters.
The driver uses the "objagg" library to perform the mask aggregation by
passing it objects that consist of the filter's mask and whether the
filter is to be inserted into the A-TCAM or the C-TCAM since filters in
different TCAMs cannot share a mask.
The set of created objects is dependent on the insertion order of the
filters and is not necessarily optimal. Therefore, the driver will
periodically ask the library to compute a more optimal set ("hints") by
looking at all the existing objects.
When the library asks the driver whether two objects can be aggregated
the driver only compares the provided masks and ignores the A-TCAM /
C-TCAM indication. This is the right thing to do since the goal is to
move as many filters as possible to the A-TCAM. The driver also forbids
two identical masks from being aggregated since this can only happen if
one was intentionally put in the C-TCAM to avoid a conflict in the
A-TCAM.
The above can result in the following set of hints:
H1: {mask X, A-TCAM} -> H2: {mask Y, A-TCAM} // X is Y + delta
H3: {mask Y, C-TCAM} -> H4: {mask Z, A-TCAM} // Y is Z + delta
After getting the hints from the library the driver will start migrating
filters from one region to another while consulting the computed hints
and instructing the device to perform a lookup in both regions during
the transition.
Assuming a filter with mask X is being migrated into the A-TCAM in the
new region, the hints lookup will return H1. Since H2 is the parent of
H1, the library will try to find the object associated with it and
create it if necessary in which case another hints lookup (recursive)
will be performed. This hints lookup for {mask Y, A-TCAM} will either
return H2 or H3 since the driver passes the library an object comparison
function that ignores the A-TCAM / C-TCAM indication.
This can eventually lead to nested objects which are not supported by
the library [1].
Fix by removing the object comparison function from both the driver and
the library as the driver was the only user. That way the lookup will
only return exact matches.
I do not have a reliable reproducer that can reproduce the issue in a
timely manner, but before the fix the issue would reproduce in several
minutes and with the fix it does not reproduce in over an hour.
Note that the current usefulness of the hints is limited because they
include the C-TCAM indication and represent aggregation that cannot
actually happen. This will be addressed in net-next.
[1]
WARNING: CPU: 0 PID: 153 at lib/objagg.c:170 objagg_obj_parent_assign+0xb5/0xd0
Modules linked in:
CPU: 0 PID: 153 Comm: kworker/0:18 Not tainted 6.9.0-rc6-custom-g70fbc2c1c38b #42
Hardware name: Mellanox Technologies Ltd. MSN3700C/VMOD0008, BIOS 5.11 10/10/2018
Workqueue: mlxsw_core mlxsw_sp_acl_tcam_vregion_rehash_work
RIP: 0010:objagg_obj_parent_assign+0xb5/0xd0
[...]
Call Trace:
<TASK>
__objagg_obj_get+0x2bb/0x580
objagg_obj_get+0xe/0x80
mlxsw_sp_acl_erp_mask_get+0xb5/0xf0
mlxsw_sp_acl_atcam_entry_add+0xe8/0x3c0
mlxsw_sp_acl_tcam_entry_create+0x5e/0xa0
mlxsw_sp_acl_tcam_vchunk_migrate_one+0x16b/0x270
mlxsw_sp_acl_tcam_vregion_rehash_work+0xbe/0x510
process_one_work+0x151/0x370 |
| In the Linux kernel, the following vulnerability has been resolved:
nvmet: fix a possible leak when destroy a ctrl during qp establishment
In nvmet_sq_destroy we capture sq->ctrl early and if it is non-NULL we
know that a ctrl was allocated (in the admin connect request handler)
and we need to release pending AERs, clear ctrl->sqs and sq->ctrl
(for nvme-loop primarily), and drop the final reference on the ctrl.
However, a small window is possible where nvmet_sq_destroy starts (as
a result of the client giving up and disconnecting) concurrently with
the nvme admin connect cmd (which may be in an early stage). But *before*
kill_and_confirm of sq->ref (i.e. the admin connect managed to get an sq
live reference). In this case, sq->ctrl was allocated however after it was
captured in a local variable in nvmet_sq_destroy.
This prevented the final reference drop on the ctrl.
Solve this by re-capturing the sq->ctrl after all inflight request has
completed, where for sure sq->ctrl reference is final, and move forward
based on that.
This issue was observed in an environment with many hosts connecting
multiple ctrls simoutanuosly, creating a delay in allocating a ctrl
leading up to this race window. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/dasd: Fix invalid dereferencing of indirect CCW data pointer
Fix invalid dereferencing of indirect CCW data pointer in
dasd_eckd_dump_sense() that leads to a kernel panic in error cases.
When using indirect addressing for DASD CCWs (IDAW) the CCW CDA pointer
does not contain the data address itself but a pointer to the IDAL.
This needs to be translated from physical to virtual as well before
using it.
This dereferencing is also used for dasd_page_cache and also fixed
although it is very unlikely that this code path ever gets used. |
| In the Linux kernel, the following vulnerability has been resolved:
nvmet: always initialize cqe.result
The spec doesn't mandate that the first two double words (aka results)
for the command queue entry need to be set to 0 when they are not
used (not specified). Though, the target implemention returns 0 for TCP
and FC but not for RDMA.
Let's make RDMA behave the same and thus explicitly initializing the
result field. This prevents leaking any data from the stack. |
| In the Linux kernel, the following vulnerability has been resolved:
ibmvnic: Add tx check to prevent skb leak
Below is a summary of how the driver stores a reference to an skb during
transmit:
tx_buff[free_map[consumer_index]]->skb = new_skb;
free_map[consumer_index] = IBMVNIC_INVALID_MAP;
consumer_index ++;
Where variable data looks like this:
free_map == [4, IBMVNIC_INVALID_MAP, IBMVNIC_INVALID_MAP, 0, 3]
consumer_index^
tx_buff == [skb=null, skb=<ptr>, skb=<ptr>, skb=null, skb=null]
The driver has checks to ensure that free_map[consumer_index] pointed to
a valid index but there was no check to ensure that this index pointed
to an unused/null skb address. So, if, by some chance, our free_map and
tx_buff lists become out of sync then we were previously risking an
skb memory leak. This could then cause tcp congestion control to stop
sending packets, eventually leading to ETIMEDOUT.
Therefore, add a conditional to ensure that the skb address is null. If
not then warn the user (because this is still a bug that should be
patched) and free the old pointer to prevent memleak/tcp problems. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath12k: fix kernel crash during resume
Currently during resume, QMI target memory is not properly handled, resulting
in kernel crash in case DMA remap is not supported:
BUG: Bad page state in process kworker/u16:54 pfn:36e80
page: refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x36e80
page dumped because: nonzero _refcount
Call Trace:
bad_page
free_page_is_bad_report
__free_pages_ok
__free_pages
dma_direct_free
dma_free_attrs
ath12k_qmi_free_target_mem_chunk
ath12k_qmi_msg_mem_request_cb
The reason is:
Once ath12k module is loaded, firmware sends memory request to host. In case
DMA remap not supported, ath12k refuses the first request due to failure in
allocating with large segment size:
ath12k_pci 0000:04:00.0: qmi firmware request memory request
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 7077888
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 8454144
ath12k_pci 0000:04:00.0: qmi dma allocation failed (7077888 B type 1), will try later with small size
ath12k_pci 0000:04:00.0: qmi delays mem_request 2
ath12k_pci 0000:04:00.0: qmi firmware request memory request
Later firmware comes back with more but small segments and allocation
succeeds:
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 262144
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 524288
ath12k_pci 0000:04:00.0: qmi mem seg type 4 size 65536
ath12k_pci 0000:04:00.0: qmi mem seg type 1 size 524288
Now ath12k is working. If suspend is triggered, firmware will be reloaded
during resume. As same as before, firmware requests two large segments at
first. In ath12k_qmi_msg_mem_request_cb() segment count and size are
assigned:
ab->qmi.mem_seg_count == 2
ab->qmi.target_mem[0].size == 7077888
ab->qmi.target_mem[1].size == 8454144
Then allocation failed like before and ath12k_qmi_free_target_mem_chunk()
is called to free all allocated segments. Note the first segment is skipped
because its v.addr is cleared due to allocation failure:
chunk->v.addr = dma_alloc_coherent()
Also note that this leaks that segment because it has not been freed.
While freeing the second segment, a size of 8454144 is passed to
dma_free_coherent(). However remember that this segment is allocated at
the first time firmware is loaded, before suspend. So its real size is
524288, much smaller than 8454144. As a result kernel found we are freeing
some memory which is in use and thus cras
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
media: i2c: et8ek8: Don't strip remove function when driver is builtin
Using __exit for the remove function results in the remove callback
being discarded with CONFIG_VIDEO_ET8EK8=y. When such a device gets
unbound (e.g. using sysfs or hotplug), the driver is just removed
without the cleanup being performed. This results in resource leaks. Fix
it by compiling in the remove callback unconditionally.
This also fixes a W=1 modpost warning:
WARNING: modpost: drivers/media/i2c/et8ek8/et8ek8: section mismatch in reference: et8ek8_i2c_driver+0x10 (section: .data) -> et8ek8_remove (section: .exit.text) |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/hns: Modify the print level of CQE error
Too much print may lead to a panic in kernel. Change ibdev_err() to
ibdev_err_ratelimited(), and change the printing level of cqe dump
to debug level. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/cma: Fix kmemleak in rdma_core observed during blktests nvme/rdma use siw
When running blktests nvme/rdma, the following kmemleak issue will appear.
kmemleak: Kernel memory leak detector initialized (mempool available:36041)
kmemleak: Automatic memory scanning thread started
kmemleak: 2 new suspected memory leaks (see /sys/kernel/debug/kmemleak)
kmemleak: 8 new suspected memory leaks (see /sys/kernel/debug/kmemleak)
kmemleak: 17 new suspected memory leaks (see /sys/kernel/debug/kmemleak)
kmemleak: 4 new suspected memory leaks (see /sys/kernel/debug/kmemleak)
unreferenced object 0xffff88855da53400 (size 192):
comm "rdma", pid 10630, jiffies 4296575922
hex dump (first 32 bytes):
37 00 00 00 00 00 00 00 c0 ff ff ff 1f 00 00 00 7...............
10 34 a5 5d 85 88 ff ff 10 34 a5 5d 85 88 ff ff .4.].....4.]....
backtrace (crc 47f66721):
[<ffffffff911251bd>] kmalloc_trace+0x30d/0x3b0
[<ffffffffc2640ff7>] alloc_gid_entry+0x47/0x380 [ib_core]
[<ffffffffc2642206>] add_modify_gid+0x166/0x930 [ib_core]
[<ffffffffc2643468>] ib_cache_update.part.0+0x6d8/0x910 [ib_core]
[<ffffffffc2644e1a>] ib_cache_setup_one+0x24a/0x350 [ib_core]
[<ffffffffc263949e>] ib_register_device+0x9e/0x3a0 [ib_core]
[<ffffffffc2a3d389>] 0xffffffffc2a3d389
[<ffffffffc2688cd8>] nldev_newlink+0x2b8/0x520 [ib_core]
[<ffffffffc2645fe3>] rdma_nl_rcv_msg+0x2c3/0x520 [ib_core]
[<ffffffffc264648c>]
rdma_nl_rcv_skb.constprop.0.isra.0+0x23c/0x3a0 [ib_core]
[<ffffffff9270e7b5>] netlink_unicast+0x445/0x710
[<ffffffff9270f1f1>] netlink_sendmsg+0x761/0xc40
[<ffffffff9249db29>] __sys_sendto+0x3a9/0x420
[<ffffffff9249dc8c>] __x64_sys_sendto+0xdc/0x1b0
[<ffffffff92db0ad3>] do_syscall_64+0x93/0x180
[<ffffffff92e00126>] entry_SYSCALL_64_after_hwframe+0x71/0x79
The root cause: rdma_put_gid_attr is not called when sgid_attr is set
to ERR_PTR(-ENODEV). |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: hda/cs_dsp_ctl: Use private_free for control cleanup
Use the control private_free callback to free the associated data
block. This ensures that the memory won't leak, whatever way the
control gets destroyed.
The original implementation didn't actually remove the ALSA
controls in hda_cs_dsp_control_remove(). It only freed the internal
tracking structure. This meant it was possible to remove/unload the
amp driver while leaving its ALSA controls still present in the
soundcard. Obviously attempting to access them could cause segfaults
or at least dereferencing stale pointers. |
| In the Linux kernel, the following vulnerability has been resolved:
blk-cgroup: fix list corruption from reorder of WRITE ->lqueued
__blkcg_rstat_flush() can be run anytime, especially when blk_cgroup_bio_start
is being executed.
If WRITE of `->lqueued` is re-ordered with READ of 'bisc->lnode.next' in
the loop of __blkcg_rstat_flush(), `next_bisc` can be assigned with one
stat instance being added in blk_cgroup_bio_start(), then the local
list in __blkcg_rstat_flush() could be corrupted.
Fix the issue by adding one barrier. |
| In the Linux kernel, the following vulnerability has been resolved:
net/smc: fix neighbour and rtable leak in smc_ib_find_route()
In smc_ib_find_route(), the neighbour found by neigh_lookup() and rtable
resolved by ip_route_output_flow() are not released or put before return.
It may cause the refcount leak, so fix it. |
| In the Linux kernel, the following vulnerability has been resolved:
Drivers: hv: vmbus: Leak pages if set_memory_encrypted() fails
In CoCo VMs it is possible for the untrusted host to cause
set_memory_encrypted() or set_memory_decrypted() to fail such that an
error is returned and the resulting memory is shared. Callers need to
take care to handle these errors to avoid returning decrypted (shared)
memory to the page allocator, which could lead to functional or security
issues.
VMBus code could free decrypted pages if set_memory_encrypted()/decrypted()
fails. Leak the pages if this happens. |
| In the Linux kernel, the following vulnerability has been resolved:
Drivers: hv: vmbus: Track decrypted status in vmbus_gpadl
In CoCo VMs it is possible for the untrusted host to cause
set_memory_encrypted() or set_memory_decrypted() to fail such that an
error is returned and the resulting memory is shared. Callers need to
take care to handle these errors to avoid returning decrypted (shared)
memory to the page allocator, which could lead to functional or security
issues.
In order to make sure callers of vmbus_establish_gpadl() and
vmbus_teardown_gpadl() don't return decrypted/shared pages to
allocators, add a field in struct vmbus_gpadl to keep track of the
decryption status of the buffers. This will allow the callers to
know if they should free or leak the pages. |
| In the Linux kernel, the following vulnerability has been resolved:
hv_netvsc: Don't free decrypted memory
In CoCo VMs it is possible for the untrusted host to cause
set_memory_encrypted() or set_memory_decrypted() to fail such that an
error is returned and the resulting memory is shared. Callers need to
take care to handle these errors to avoid returning decrypted (shared)
memory to the page allocator, which could lead to functional or security
issues.
The netvsc driver could free decrypted/shared pages if
set_memory_decrypted() fails. Check the decrypted field in the gpadl
to decide whether to free the memory. |
| In the Linux kernel, the following vulnerability has been resolved:
uio_hv_generic: Don't free decrypted memory
In CoCo VMs it is possible for the untrusted host to cause
set_memory_encrypted() or set_memory_decrypted() to fail such that an
error is returned and the resulting memory is shared. Callers need to
take care to handle these errors to avoid returning decrypted (shared)
memory to the page allocator, which could lead to functional or security
issues.
The VMBus device UIO driver could free decrypted/shared pages if
set_memory_decrypted() fails. Check the decrypted field in the gpadl
to decide whether to free the memory. |
| In the Linux kernel, the following vulnerability has been resolved:
Drivers: hv: vmbus: Don't free ring buffers that couldn't be re-encrypted
In CoCo VMs it is possible for the untrusted host to cause
set_memory_encrypted() or set_memory_decrypted() to fail such that an
error is returned and the resulting memory is shared. Callers need to
take care to handle these errors to avoid returning decrypted (shared)
memory to the page allocator, which could lead to functional or security
issues.
The VMBus ring buffer code could free decrypted/shared pages if
set_memory_decrypted() fails. Check the decrypted field in the struct
vmbus_gpadl for the ring buffers to decide whether to free the memory. |
| In the Linux kernel, the following vulnerability has been resolved:
firmware: qcom: uefisecapp: Fix memory related IO errors and crashes
It turns out that while the QSEECOM APP_SEND command has specific fields
for request and response buffers, uefisecapp expects them both to be in
a single memory region. Failure to adhere to this has (so far) resulted
in either no response being written to the response buffer (causing an
EIO to be emitted down the line), the SCM call to fail with EINVAL
(i.e., directly from TZ/firmware), or the device to be hard-reset.
While this issue can be triggered deterministically, in the current form
it seems to happen rather sporadically (which is why it has gone
unnoticed during earlier testing). This is likely due to the two
kzalloc() calls (for request and response) being directly after each
other. Which means that those likely return consecutive regions most of
the time, especially when not much else is going on in the system.
Fix this by allocating a single memory region for both request and
response buffers, properly aligning both structs inside it. This
unfortunately also means that the qcom_scm_qseecom_app_send() interface
needs to be restructured, as it should no longer map the DMA regions
separately. Therefore, move the responsibility of DMA allocation (or
mapping) to the caller. |
