| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
mlxsw: spectrum_acl_tcam: Fix stack corruption
When tc filters are first added to a net device, the corresponding local
port gets bound to an ACL group in the device. The group contains a list
of ACLs. In turn, each ACL points to a different TCAM region where the
filters are stored. During forwarding, the ACLs are sequentially
evaluated until a match is found.
One reason to place filters in different regions is when they are added
with decreasing priorities and in an alternating order so that two
consecutive filters can never fit in the same region because of their
key usage.
In Spectrum-2 and newer ASICs the firmware started to report that the
maximum number of ACLs in a group is more than 16, but the layout of the
register that configures ACL groups (PAGT) was not updated to account
for that. It is therefore possible to hit stack corruption [1] in the
rare case where more than 16 ACLs in a group are required.
Fix by limiting the maximum ACL group size to the minimum between what
the firmware reports and the maximum ACLs that fit in the PAGT register.
Add a test case to make sure the machine does not crash when this
condition is hit.
[1]
Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: mlxsw_sp_acl_tcam_group_update+0x116/0x120
[...]
dump_stack_lvl+0x36/0x50
panic+0x305/0x330
__stack_chk_fail+0x15/0x20
mlxsw_sp_acl_tcam_group_update+0x116/0x120
mlxsw_sp_acl_tcam_group_region_attach+0x69/0x110
mlxsw_sp_acl_tcam_vchunk_get+0x492/0xa20
mlxsw_sp_acl_tcam_ventry_add+0x25/0xe0
mlxsw_sp_acl_rule_add+0x47/0x240
mlxsw_sp_flower_replace+0x1a9/0x1d0
tc_setup_cb_add+0xdc/0x1c0
fl_hw_replace_filter+0x146/0x1f0
fl_change+0xc17/0x1360
tc_new_tfilter+0x472/0xb90
rtnetlink_rcv_msg+0x313/0x3b0
netlink_rcv_skb+0x58/0x100
netlink_unicast+0x244/0x390
netlink_sendmsg+0x1e4/0x440
____sys_sendmsg+0x164/0x260
___sys_sendmsg+0x9a/0xe0
__sys_sendmsg+0x7a/0xc0
do_syscall_64+0x40/0xe0
entry_SYSCALL_64_after_hwframe+0x63/0x6b |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/bpf/32: Fix Oops on tail call tests
test_bpf tail call tests end up as:
test_bpf: #0 Tail call leaf jited:1 85 PASS
test_bpf: #1 Tail call 2 jited:1 111 PASS
test_bpf: #2 Tail call 3 jited:1 145 PASS
test_bpf: #3 Tail call 4 jited:1 170 PASS
test_bpf: #4 Tail call load/store leaf jited:1 190 PASS
test_bpf: #5 Tail call load/store jited:1
BUG: Unable to handle kernel data access on write at 0xf1b4e000
Faulting instruction address: 0xbe86b710
Oops: Kernel access of bad area, sig: 11 [#1]
BE PAGE_SIZE=4K MMU=Hash PowerMac
Modules linked in: test_bpf(+)
CPU: 0 PID: 97 Comm: insmod Not tainted 6.1.0-rc4+ #195
Hardware name: PowerMac3,1 750CL 0x87210 PowerMac
NIP: be86b710 LR: be857e88 CTR: be86b704
REGS: f1b4df20 TRAP: 0300 Not tainted (6.1.0-rc4+)
MSR: 00009032 <EE,ME,IR,DR,RI> CR: 28008242 XER: 00000000
DAR: f1b4e000 DSISR: 42000000
GPR00: 00000001 f1b4dfe0 c11d2280 00000000 00000000 00000000 00000002 00000000
GPR08: f1b4e000 be86b704 f1b4e000 00000000 00000000 100d816a f2440000 fe73baa8
GPR16: f2458000 00000000 c1941ae4 f1fe2248 00000045 c0de0000 f2458030 00000000
GPR24: 000003e8 0000000f f2458000 f1b4dc90 3e584b46 00000000 f24466a0 c1941a00
NIP [be86b710] 0xbe86b710
LR [be857e88] __run_one+0xec/0x264 [test_bpf]
Call Trace:
[f1b4dfe0] [00000002] 0x2 (unreliable)
Instruction dump:
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
---[ end trace 0000000000000000 ]---
This is a tentative to write above the stack. The problem is encoutered
with tests added by commit 38608ee7b690 ("bpf, tests: Add load store
test case for tail call")
This happens because tail call is done to a BPF prog with a different
stack_depth. At the time being, the stack is kept as is when the caller
tail calls its callee. But at exit, the callee restores the stack based
on its own properties. Therefore here, at each run, r1 is erroneously
increased by 32 - 16 = 16 bytes.
This was done that way in order to pass the tail call count from caller
to callee through the stack. As powerpc32 doesn't have a red zone in
the stack, it was necessary the maintain the stack as is for the tail
call. But it was not anticipated that the BPF frame size could be
different.
Let's take a new approach. Use register r4 to carry the tail call count
during the tail call, and save it into the stack at function entry if
required. This means the input parameter must be in r3, which is more
correct as it is a 32 bits parameter, then tail call better match with
normal BPF function entry, the down side being that we move that input
parameter back and forth between r3 and r4. That can be optimised later.
Doing that also has the advantage of maximising the common parts between
tail calls and a normal function exit.
With the fix, tail call tests are now successfull:
test_bpf: #0 Tail call leaf jited:1 53 PASS
test_bpf: #1 Tail call 2 jited:1 115 PASS
test_bpf: #2 Tail call 3 jited:1 154 PASS
test_bpf: #3 Tail call 4 jited:1 165 PASS
test_bpf: #4 Tail call load/store leaf jited:1 101 PASS
test_bpf: #5 Tail call load/store jited:1 141 PASS
test_bpf: #6 Tail call error path, max count reached jited:1 994 PASS
test_bpf: #7 Tail call count preserved across function calls jited:1 140975 PASS
test_bpf: #8 Tail call error path, NULL target jited:1 110 PASS
test_bpf: #9 Tail call error path, index out of range jited:1 69 PASS
test_bpf: test_tail_calls: Summary: 10 PASSED, 0 FAILED, [10/10 JIT'ed] |
| In the Linux kernel, the following vulnerability has been resolved:
net: dsa: sja1105: avoid out of bounds access in sja1105_init_l2_policing()
The SJA1105 family has 45 L2 policing table entries
(SJA1105_MAX_L2_POLICING_COUNT) and SJA1110 has 110
(SJA1110_MAX_L2_POLICING_COUNT). Keeping the table structure but
accounting for the difference in port count (5 in SJA1105 vs 10 in
SJA1110) does not fully explain the difference. Rather, the SJA1110 also
has L2 ingress policers for multicast traffic. If a packet is classified
as multicast, it will be processed by the policer index 99 + SRCPORT.
The sja1105_init_l2_policing() function initializes all L2 policers such
that they don't interfere with normal packet reception by default. To have
a common code between SJA1105 and SJA1110, the index of the multicast
policer for the port is calculated because it's an index that is out of
bounds for SJA1105 but in bounds for SJA1110, and a bounds check is
performed.
The code fails to do the proper thing when determining what to do with the
multicast policer of port 0 on SJA1105 (ds->num_ports = 5). The "mcast"
index will be equal to 45, which is also equal to
table->ops->max_entry_count (SJA1105_MAX_L2_POLICING_COUNT). So it passes
through the check. But at the same time, SJA1105 doesn't have multicast
policers. So the code programs the SHARINDX field of an out-of-bounds
element in the L2 Policing table of the static config.
The comparison between index 45 and 45 entries should have determined the
code to not access this policer index on SJA1105, since its memory wasn't
even allocated.
With enough bad luck, the out-of-bounds write could even overwrite other
valid kernel data, but in this case, the issue was detected using KASAN.
Kernel log:
sja1105 spi5.0: Probed switch chip: SJA1105Q
==================================================================
BUG: KASAN: slab-out-of-bounds in sja1105_setup+0x1cbc/0x2340
Write of size 8 at addr ffffff880bd57708 by task kworker/u8:0/8
...
Workqueue: events_unbound deferred_probe_work_func
Call trace:
...
sja1105_setup+0x1cbc/0x2340
dsa_register_switch+0x1284/0x18d0
sja1105_probe+0x748/0x840
...
Allocated by task 8:
...
sja1105_setup+0x1bcc/0x2340
dsa_register_switch+0x1284/0x18d0
sja1105_probe+0x748/0x840
... |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: tsc2046: fix memory corruption by preventing array overflow
On one side we have indio_dev->num_channels includes all physical channels +
timestamp channel. On other side we have an array allocated only for
physical channels. So, fix memory corruption by ARRAY_SIZE() instead of
num_channels variable.
Note the first case is a cleanup rather than a fix as the software
timestamp channel bit in active_scanmask is never set by the IIO core. |
| In the Linux kernel, the following vulnerability has been resolved:
tty: serial: qcom-geni-serial: fix slab-out-of-bounds on RX FIFO buffer
Driver's probe allocates memory for RX FIFO (port->rx_fifo) based on
default RX FIFO depth, e.g. 16. Later during serial startup the
qcom_geni_serial_port_setup() updates the RX FIFO depth
(port->rx_fifo_depth) to match real device capabilities, e.g. to 32.
The RX UART handle code will read "port->rx_fifo_depth" number of words
into "port->rx_fifo" buffer, thus exceeding the bounds. This can be
observed in certain configurations with Qualcomm Bluetooth HCI UART
device and KASAN:
Bluetooth: hci0: QCA Product ID :0x00000010
Bluetooth: hci0: QCA SOC Version :0x400a0200
Bluetooth: hci0: QCA ROM Version :0x00000200
Bluetooth: hci0: QCA Patch Version:0x00000d2b
Bluetooth: hci0: QCA controller version 0x02000200
Bluetooth: hci0: QCA Downloading qca/htbtfw20.tlv
bluetooth hci0: Direct firmware load for qca/htbtfw20.tlv failed with error -2
Bluetooth: hci0: QCA Failed to request file: qca/htbtfw20.tlv (-2)
Bluetooth: hci0: QCA Failed to download patch (-2)
==================================================================
BUG: KASAN: slab-out-of-bounds in handle_rx_uart+0xa8/0x18c
Write of size 4 at addr ffff279347d578c0 by task swapper/0/0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.1.0-rt5-00350-gb2450b7e00be-dirty #26
Hardware name: Qualcomm Technologies, Inc. Robotics RB5 (DT)
Call trace:
dump_backtrace.part.0+0xe0/0xf0
show_stack+0x18/0x40
dump_stack_lvl+0x8c/0xb8
print_report+0x188/0x488
kasan_report+0xb4/0x100
__asan_store4+0x80/0xa4
handle_rx_uart+0xa8/0x18c
qcom_geni_serial_handle_rx+0x84/0x9c
qcom_geni_serial_isr+0x24c/0x760
__handle_irq_event_percpu+0x108/0x500
handle_irq_event+0x6c/0x110
handle_fasteoi_irq+0x138/0x2cc
generic_handle_domain_irq+0x48/0x64
If the RX FIFO depth changes after probe, be sure to resize the buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
watch_queue: Fix filter limit check
In watch_queue_set_filter(), there are a couple of places where we check
that the filter type value does not exceed what the type_filter bitmap
can hold. One place calculates the number of bits by:
if (tf[i].type >= sizeof(wfilter->type_filter) * 8)
which is fine, but the second does:
if (tf[i].type >= sizeof(wfilter->type_filter) * BITS_PER_LONG)
which is not. This can lead to a couple of out-of-bounds writes due to
a too-large type:
(1) __set_bit() on wfilter->type_filter
(2) Writing more elements in wfilter->filters[] than we allocated.
Fix this by just using the proper WATCH_TYPE__NR instead, which is the
number of types we actually know about.
The bug may cause an oops looking something like:
BUG: KASAN: slab-out-of-bounds in watch_queue_set_filter+0x659/0x740
Write of size 4 at addr ffff88800d2c66bc by task watch_queue_oob/611
...
Call Trace:
<TASK>
dump_stack_lvl+0x45/0x59
print_address_description.constprop.0+0x1f/0x150
...
kasan_report.cold+0x7f/0x11b
...
watch_queue_set_filter+0x659/0x740
...
__x64_sys_ioctl+0x127/0x190
do_syscall_64+0x43/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
Allocated by task 611:
kasan_save_stack+0x1e/0x40
__kasan_kmalloc+0x81/0xa0
watch_queue_set_filter+0x23a/0x740
__x64_sys_ioctl+0x127/0x190
do_syscall_64+0x43/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
The buggy address belongs to the object at ffff88800d2c66a0
which belongs to the cache kmalloc-32 of size 32
The buggy address is located 28 bytes inside of
32-byte region [ffff88800d2c66a0, ffff88800d2c66c0) |
| In the Linux kernel, the following vulnerability has been resolved:
vt: fix memory overlapping when deleting chars in the buffer
A memory overlapping copy occurs when deleting a long line. This memory
overlapping copy can cause data corruption when scr_memcpyw is optimized
to memcpy because memcpy does not ensure its behavior if the destination
buffer overlaps with the source buffer. The line buffer is not always
broken, because the memcpy utilizes the hardware acceleration, whose
result is not deterministic.
Fix this problem by using replacing the scr_memcpyw with scr_memmovew. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath12k: fix possible out-of-bound write in ath12k_wmi_ext_hal_reg_caps()
reg_cap.phy_id is extracted from WMI event and could be an unexpected value
in case some errors happen. As a result out-of-bound write may occur to
soc->hal_reg_cap. Fix it by validating reg_cap.phy_id before using it.
This is found during code review.
Compile tested only. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix slab out of bounds write in smb_inherit_dacl()
slab out-of-bounds write is caused by that offsets is bigger than pntsd
allocation size. This patch add the check to validate 3 offsets using
allocation size. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: mvm: Fix a memory corruption issue
A few lines above, space is kzalloc()'ed for:
sizeof(struct iwl_nvm_data) +
sizeof(struct ieee80211_channel) +
sizeof(struct ieee80211_rate)
'mvm->nvm_data' is a 'struct iwl_nvm_data', so it is fine.
At the end of this structure, there is the 'channels' flex array.
Each element is of type 'struct ieee80211_channel'.
So only 1 element is allocated in this array.
When doing:
mvm->nvm_data->bands[0].channels = mvm->nvm_data->channels;
We point at the first element of the 'channels' flex array.
So this is fine.
However, when doing:
mvm->nvm_data->bands[0].bitrates =
(void *)((u8 *)mvm->nvm_data->channels + 1);
because of the "(u8 *)" cast, we add only 1 to the address of the beginning
of the flex array.
It is likely that we want point at the 'struct ieee80211_rate' allocated
just after.
Remove the spurious casting so that the pointer arithmetic works as
expected. |
| In the Linux kernel, the following vulnerability has been resolved:
pinctrl: nuvoton: wpcm450: fix out of bounds write
Write into 'pctrl->gpio_bank' happens before the check for GPIO index
validity, so out of bounds write may happen.
Found by Linux Verification Center (linuxtesting.org) with SVACE. |
| In the Linux kernel, the following vulnerability has been resolved:
erofs: fix lz4 inplace decompression
Currently EROFS can map another compressed buffer for inplace
decompression, that was used to handle the cases that some pages of
compressed data are actually not in-place I/O.
However, like most simple LZ77 algorithms, LZ4 expects the compressed
data is arranged at the end of the decompressed buffer and it
explicitly uses memmove() to handle overlapping:
__________________________________________________________
|_ direction of decompression --> ____ |_ compressed data _|
Although EROFS arranges compressed data like this, it typically maps two
individual virtual buffers so the relative order is uncertain.
Previously, it was hardly observed since LZ4 only uses memmove() for
short overlapped literals and x86/arm64 memmove implementations seem to
completely cover it up and they don't have this issue. Juhyung reported
that EROFS data corruption can be found on a new Intel x86 processor.
After some analysis, it seems that recent x86 processors with the new
FSRM feature expose this issue with "rep movsb".
Let's strictly use the decompressed buffer for lz4 inplace
decompression for now. Later, as an useful improvement, we could try
to tie up these two buffers together in the correct order. |
| In the Linux kernel, the following vulnerability has been resolved:
soc: qcom: pmic_glink_altmode: fix port sanity check
The PMIC GLINK altmode driver currently supports at most two ports.
Fix the incomplete port sanity check on notifications to avoid
accessing and corrupting memory beyond the port array if we ever get a
notification for an unsupported port. |
| In the Linux kernel, the following vulnerability has been resolved:
firmware: arm_scpi: Fix string overflow in SCPI genpd driver
Without the bound checks for scpi_pd->name, it could result in the buffer
overflow when copying the SCPI device name from the corresponding device
tree node as the name string is set at maximum size of 30.
Let us fix it by using devm_kasprintf so that the string buffer is
allocated dynamically. |
| In the Linux kernel, the following vulnerability has been resolved:
vduse: fix memory corruption in vduse_dev_ioctl()
The "config.offset" comes from the user. There needs to a check to
prevent it being out of bounds. The "config.offset" and
"dev->config_size" variables are both type u32. So if the offset if
out of bounds then the "dev->config_size - config.offset" subtraction
results in a very high u32 value. The out of bounds offset can result
in memory corruption. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: sch_ets: don't remove idle classes from the round-robin list
Shuang reported that the following script:
1) tc qdisc add dev ddd0 handle 10: parent 1: ets bands 8 strict 4 priomap 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7
2) mausezahn ddd0 -A 10.10.10.1 -B 10.10.10.2 -c 0 -a own -b 00:c1:a0:c1:a0:00 -t udp &
3) tc qdisc change dev ddd0 handle 10: ets bands 4 strict 2 quanta 2500 2500 priomap 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3
crashes systematically when line 2) is commented:
list_del corruption, ffff8e028404bd30->next is LIST_POISON1 (dead000000000100)
------------[ cut here ]------------
kernel BUG at lib/list_debug.c:47!
invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
CPU: 0 PID: 954 Comm: tc Not tainted 5.16.0-rc4+ #478
Hardware name: Red Hat KVM, BIOS 1.11.1-4.module+el8.1.0+4066+0f1aadab 04/01/2014
RIP: 0010:__list_del_entry_valid.cold.1+0x12/0x47
Code: fe ff 0f 0b 48 89 c1 4c 89 c6 48 c7 c7 08 42 1b 87 e8 1d c5 fe ff 0f 0b 48 89 fe 48 89 c2 48 c7 c7 98 42 1b 87 e8 09 c5 fe ff <0f> 0b 48 c7 c7 48 43 1b 87 e8 fb c4 fe ff 0f 0b 48 89 f2 48 89 fe
RSP: 0018:ffffae46807a3888 EFLAGS: 00010246
RAX: 000000000000004e RBX: 0000000000000007 RCX: 0000000000000202
RDX: 0000000000000000 RSI: ffffffff871ac536 RDI: 00000000ffffffff
RBP: ffffae46807a3a10 R08: 0000000000000000 R09: c0000000ffff7fff
R10: 0000000000000001 R11: ffffae46807a36a8 R12: ffff8e028404b800
R13: ffff8e028404bd30 R14: dead000000000100 R15: ffff8e02fafa2400
FS: 00007efdc92e4480(0000) GS:ffff8e02fb600000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000682f48 CR3: 00000001058be000 CR4: 0000000000350ef0
Call Trace:
<TASK>
ets_qdisc_change+0x58b/0xa70 [sch_ets]
tc_modify_qdisc+0x323/0x880
rtnetlink_rcv_msg+0x169/0x4a0
netlink_rcv_skb+0x50/0x100
netlink_unicast+0x1a5/0x280
netlink_sendmsg+0x257/0x4d0
sock_sendmsg+0x5b/0x60
____sys_sendmsg+0x1f2/0x260
___sys_sendmsg+0x7c/0xc0
__sys_sendmsg+0x57/0xa0
do_syscall_64+0x3a/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7efdc8031338
Code: 89 02 48 c7 c0 ff ff ff ff eb b5 0f 1f 80 00 00 00 00 f3 0f 1e fa 48 8d 05 25 43 2c 00 8b 00 85 c0 75 17 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 58 c3 0f 1f 80 00 00 00 00 41 54 41 89 d4 55
RSP: 002b:00007ffdf1ce9828 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 0000000061b37a97 RCX: 00007efdc8031338
RDX: 0000000000000000 RSI: 00007ffdf1ce9890 RDI: 0000000000000003
RBP: 0000000000000000 R08: 0000000000000001 R09: 000000000078a940
R10: 000000000000000c R11: 0000000000000246 R12: 0000000000000001
R13: 0000000000688880 R14: 0000000000000000 R15: 0000000000000000
</TASK>
Modules linked in: sch_ets sch_tbf dummy rfkill iTCO_wdt iTCO_vendor_support intel_rapl_msr intel_rapl_common joydev pcspkr i2c_i801 virtio_balloon i2c_smbus lpc_ich ip_tables xfs libcrc32c crct10dif_pclmul crc32_pclmul crc32c_intel serio_raw ghash_clmulni_intel ahci libahci libata virtio_blk virtio_console virtio_net net_failover failover sunrpc dm_mirror dm_region_hash dm_log dm_mod [last unloaded: sch_ets]
---[ end trace f35878d1912655c2 ]---
RIP: 0010:__list_del_entry_valid.cold.1+0x12/0x47
Code: fe ff 0f 0b 48 89 c1 4c 89 c6 48 c7 c7 08 42 1b 87 e8 1d c5 fe ff 0f 0b 48 89 fe 48 89 c2 48 c7 c7 98 42 1b 87 e8 09 c5 fe ff <0f> 0b 48 c7 c7 48 43 1b 87 e8 fb c4 fe ff 0f 0b 48 89 f2 48 89 fe
RSP: 0018:ffffae46807a3888 EFLAGS: 00010246
RAX: 000000000000004e RBX: 0000000000000007 RCX: 0000000000000202
RDX: 0000000000000000 RSI: ffffffff871ac536 RDI: 00000000ffffffff
RBP: ffffae46807a3a10 R08: 0000000000000000 R09: c0000000ffff7fff
R10: 0000000000000001 R11: ffffae46807a36a8 R12: ffff8e028404b800
R13: ffff8e028404bd30 R14: dead000000000100 R15: ffff8e02fafa2400
FS: 00007efdc92e4480(0000) GS:ffff8e02fb600000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000000
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm/a6xx: Allocate enough space for GMU registers
In commit 142639a52a01 ("drm/msm/a6xx: fix crashstate capture for
A650") we changed a6xx_get_gmu_registers() to read 3 sets of
registers. Unfortunately, we didn't change the memory allocation for
the array. That leads to a KASAN warning (this was on the chromeos-5.4
kernel, which has the problematic commit backported to it):
BUG: KASAN: slab-out-of-bounds in _a6xx_get_gmu_registers+0x144/0x430
Write of size 8 at addr ffffff80c89432b0 by task A618-worker/209
CPU: 5 PID: 209 Comm: A618-worker Tainted: G W 5.4.156-lockdep #22
Hardware name: Google Lazor Limozeen without Touchscreen (rev5 - rev8) (DT)
Call trace:
dump_backtrace+0x0/0x248
show_stack+0x20/0x2c
dump_stack+0x128/0x1ec
print_address_description+0x88/0x4a0
__kasan_report+0xfc/0x120
kasan_report+0x10/0x18
__asan_report_store8_noabort+0x1c/0x24
_a6xx_get_gmu_registers+0x144/0x430
a6xx_gpu_state_get+0x330/0x25d4
msm_gpu_crashstate_capture+0xa0/0x84c
recover_worker+0x328/0x838
kthread_worker_fn+0x32c/0x574
kthread+0x2dc/0x39c
ret_from_fork+0x10/0x18
Allocated by task 209:
__kasan_kmalloc+0xfc/0x1c4
kasan_kmalloc+0xc/0x14
kmem_cache_alloc_trace+0x1f0/0x2a0
a6xx_gpu_state_get+0x164/0x25d4
msm_gpu_crashstate_capture+0xa0/0x84c
recover_worker+0x328/0x838
kthread_worker_fn+0x32c/0x574
kthread+0x2dc/0x39c
ret_from_fork+0x10/0x18 |
| In the Linux kernel, the following vulnerability has been resolved:
mlxsw: thermal: Fix out-of-bounds memory accesses
Currently, mlxsw allows cooling states to be set above the maximum
cooling state supported by the driver:
# cat /sys/class/thermal/thermal_zone2/cdev0/type
mlxsw_fan
# cat /sys/class/thermal/thermal_zone2/cdev0/max_state
10
# echo 18 > /sys/class/thermal/thermal_zone2/cdev0/cur_state
# echo $?
0
This results in out-of-bounds memory accesses when thermal state
transition statistics are enabled (CONFIG_THERMAL_STATISTICS=y), as the
transition table is accessed with a too large index (state) [1].
According to the thermal maintainer, it is the responsibility of the
driver to reject such operations [2].
Therefore, return an error when the state to be set exceeds the maximum
cooling state supported by the driver.
To avoid dead code, as suggested by the thermal maintainer [3],
partially revert commit a421ce088ac8 ("mlxsw: core: Extend cooling
device with cooling levels") that tried to interpret these invalid
cooling states (above the maximum) in a special way. The cooling levels
array is not removed in order to prevent the fans going below 20% PWM,
which would cause them to get stuck at 0% PWM.
[1]
BUG: KASAN: slab-out-of-bounds in thermal_cooling_device_stats_update+0x271/0x290
Read of size 4 at addr ffff8881052f7bf8 by task kworker/0:0/5
CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.15.0-rc3-custom-45935-gce1adf704b14 #122
Hardware name: Mellanox Technologies Ltd. "MSN2410-CB2FO"/"SA000874", BIOS 4.6.5 03/08/2016
Workqueue: events_freezable_power_ thermal_zone_device_check
Call Trace:
dump_stack_lvl+0x8b/0xb3
print_address_description.constprop.0+0x1f/0x140
kasan_report.cold+0x7f/0x11b
thermal_cooling_device_stats_update+0x271/0x290
__thermal_cdev_update+0x15e/0x4e0
thermal_cdev_update+0x9f/0xe0
step_wise_throttle+0x770/0xee0
thermal_zone_device_update+0x3f6/0xdf0
process_one_work+0xa42/0x1770
worker_thread+0x62f/0x13e0
kthread+0x3ee/0x4e0
ret_from_fork+0x1f/0x30
Allocated by task 1:
kasan_save_stack+0x1b/0x40
__kasan_kmalloc+0x7c/0x90
thermal_cooling_device_setup_sysfs+0x153/0x2c0
__thermal_cooling_device_register.part.0+0x25b/0x9c0
thermal_cooling_device_register+0xb3/0x100
mlxsw_thermal_init+0x5c5/0x7e0
__mlxsw_core_bus_device_register+0xcb3/0x19c0
mlxsw_core_bus_device_register+0x56/0xb0
mlxsw_pci_probe+0x54f/0x710
local_pci_probe+0xc6/0x170
pci_device_probe+0x2b2/0x4d0
really_probe+0x293/0xd10
__driver_probe_device+0x2af/0x440
driver_probe_device+0x51/0x1e0
__driver_attach+0x21b/0x530
bus_for_each_dev+0x14c/0x1d0
bus_add_driver+0x3ac/0x650
driver_register+0x241/0x3d0
mlxsw_sp_module_init+0xa2/0x174
do_one_initcall+0xee/0x5f0
kernel_init_freeable+0x45a/0x4de
kernel_init+0x1f/0x210
ret_from_fork+0x1f/0x30
The buggy address belongs to the object at ffff8881052f7800
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 1016 bytes inside of
1024-byte region [ffff8881052f7800, ffff8881052f7c00)
The buggy address belongs to the page:
page:0000000052355272 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x1052f0
head:0000000052355272 order:3 compound_mapcount:0 compound_pincount:0
flags: 0x200000000010200(slab|head|node=0|zone=2)
raw: 0200000000010200 ffffea0005034800 0000000300000003 ffff888100041dc0
raw: 0000000000000000 0000000000100010 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8881052f7a80: 00 00 00 00 00 00 04 fc fc fc fc fc fc fc fc fc
ffff8881052f7b00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff8881052f7b80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
ffff8881052f7c00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff8881052f7c80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[2] https://lore.kernel.org/linux-pm/9aca37cb-1629-5c67-
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
bus: mhi: core: Validate channel ID when processing command completions
MHI reads the channel ID from the event ring element sent by the
device which can be any value between 0 and 255. In order to
prevent any out of bound accesses, add a check against the maximum
number of channels supported by the controller and those channels
not configured yet so as to skip processing of that event ring
element. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: bcm2835: Fix out-of-bounds access with more than 4 slaves
Commit 571e31fa60b3 ("spi: bcm2835: Cache CS register value for
->prepare_message()") limited the number of slaves to 3 at compile-time.
The limitation was necessitated by a statically-sized array prepare_cs[]
in the driver private data which contains a per-slave register value.
The commit sought to enforce the limitation at run-time by setting the
controller's num_chipselect to 3: Slaves with a higher chipselect are
rejected by spi_add_device().
However the commit neglected that num_chipselect only limits the number
of *native* chipselects. If GPIO chipselects are specified in the
device tree for more than 3 slaves, num_chipselect is silently raised by
of_spi_get_gpio_numbers() and the result are out-of-bounds accesses to
the statically-sized array prepare_cs[].
As a bandaid fix which is backportable to stable, raise the number of
allowed slaves to 24 (which "ought to be enough for anybody"), enforce
the limitation on slave ->setup and revert num_chipselect to 3 (which is
the number of native chipselects supported by the controller).
An upcoming for-next commit will allow an arbitrary number of slaves. |
