| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
m68k: mvme147,mvme16x: Don't wipe PCC timer config bits
Don't clear the timer 1 configuration bits when clearing the interrupt flag
and counter overflow. As Michael reported, "This results in no timer
interrupts being delivered after the first. Initialization then hangs
in calibrate_delay as the jiffies counter is not updated."
On mvme16x, enable the timer after requesting the irq, consistent with
mvme147. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix to avoid touching checkpointed data in get_victim()
In CP disabling mode, there are two issues when using LFS or SSR | AT_SSR
mode to select victim:
1. LFS is set to find source section during GC, the victim should have
no checkpointed data, since after GC, section could not be set free for
reuse.
Previously, we only check valid chpt blocks in current segment rather
than section, fix it.
2. SSR | AT_SSR are set to find target segment for writes which can be
fully filled by checkpointed and newly written blocks, we should never
select such segment, otherwise it can cause panic or data corruption
during allocation, potential case is described as below:
a) target segment has 'n' (n < 512) ckpt valid blocks
b) GC migrates 'n' valid blocks to other segment (segment is still
in dirty list)
c) GC migrates '512 - n' blocks to target segment (segment has 'n'
cp_vblocks and '512 - n' vblocks)
d) If GC selects target segment via {AT,}SSR allocator, however there
is no free space in targe segment. |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: entry: always set GIC_PRIO_PSR_I_SET during entry
Zenghui reports that booting a kernel with "irqchip.gicv3_pseudo_nmi=1"
on the command line hits a warning during kernel entry, due to the way
we manipulate the PMR.
Early in the entry sequence, we call lockdep_hardirqs_off() to inform
lockdep that interrupts have been masked (as the HW sets DAIF wqhen
entering an exception). Architecturally PMR_EL1 is not affected by
exception entry, and we don't set GIC_PRIO_PSR_I_SET in the PMR early in
the exception entry sequence, so early in exception entry the PMR can
indicate that interrupts are unmasked even though they are masked by
DAIF.
If DEBUG_LOCKDEP is selected, lockdep_hardirqs_off() will check that
interrupts are masked, before we set GIC_PRIO_PSR_I_SET in any of the
exception entry paths, and hence lockdep_hardirqs_off() will WARN() that
something is amiss.
We can avoid this by consistently setting GIC_PRIO_PSR_I_SET during
exception entry so that kernel code sees a consistent environment. We
must also update local_daif_inherit() to undo this, as currently only
touches DAIF. For other paths, local_daif_restore() will update both
DAIF and the PMR. With this done, we can remove the existing special
cases which set this later in the entry code.
We always use (GIC_PRIO_IRQON | GIC_PRIO_PSR_I_SET) for consistency with
local_daif_save(), as this will warn if it ever encounters
(GIC_PRIO_IRQOFF | GIC_PRIO_PSR_I_SET), and never sets this itself. This
matches the gic_prio_kentry_setup that we have to retain for
ret_to_user.
The original splat from Zenghui's report was:
| DEBUG_LOCKS_WARN_ON(!irqs_disabled())
| WARNING: CPU: 3 PID: 125 at kernel/locking/lockdep.c:4258 lockdep_hardirqs_off+0xd4/0xe8
| Modules linked in:
| CPU: 3 PID: 125 Comm: modprobe Tainted: G W 5.12.0-rc8+ #463
| Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
| pstate: 604003c5 (nZCv DAIF +PAN -UAO -TCO BTYPE=--)
| pc : lockdep_hardirqs_off+0xd4/0xe8
| lr : lockdep_hardirqs_off+0xd4/0xe8
| sp : ffff80002a39bad0
| pmr_save: 000000e0
| x29: ffff80002a39bad0 x28: ffff0000de214bc0
| x27: ffff0000de1c0400 x26: 000000000049b328
| x25: 0000000000406f30 x24: ffff0000de1c00a0
| x23: 0000000020400005 x22: ffff8000105f747c
| x21: 0000000096000044 x20: 0000000000498ef9
| x19: ffff80002a39bc88 x18: ffffffffffffffff
| x17: 0000000000000000 x16: ffff800011c61eb0
| x15: ffff800011700a88 x14: 0720072007200720
| x13: 0720072007200720 x12: 0720072007200720
| x11: 0720072007200720 x10: 0720072007200720
| x9 : ffff80002a39bad0 x8 : ffff80002a39bad0
| x7 : ffff8000119f0800 x6 : c0000000ffff7fff
| x5 : ffff8000119f07a8 x4 : 0000000000000001
| x3 : 9bcdab23f2432800 x2 : ffff800011730538
| x1 : 9bcdab23f2432800 x0 : 0000000000000000
| Call trace:
| lockdep_hardirqs_off+0xd4/0xe8
| enter_from_kernel_mode.isra.5+0x7c/0xa8
| el1_abort+0x24/0x100
| el1_sync_handler+0x80/0xd0
| el1_sync+0x6c/0x100
| __arch_clear_user+0xc/0x90
| load_elf_binary+0x9fc/0x1450
| bprm_execve+0x404/0x880
| kernel_execve+0x180/0x188
| call_usermodehelper_exec_async+0xdc/0x158
| ret_from_fork+0x10/0x18 |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: nVMX: Always make an attempt to map eVMCS after migration
When enlightened VMCS is in use and nested state is migrated with
vmx_get_nested_state()/vmx_set_nested_state() KVM can't map evmcs
page right away: evmcs gpa is not 'struct kvm_vmx_nested_state_hdr'
and we can't read it from VP assist page because userspace may decide
to restore HV_X64_MSR_VP_ASSIST_PAGE after restoring nested state
(and QEMU, for example, does exactly that). To make sure eVMCS is
mapped /vmx_set_nested_state() raises KVM_REQ_GET_NESTED_STATE_PAGES
request.
Commit f2c7ef3ba955 ("KVM: nSVM: cancel KVM_REQ_GET_NESTED_STATE_PAGES
on nested vmexit") added KVM_REQ_GET_NESTED_STATE_PAGES clearing to
nested_vmx_vmexit() to make sure MSR permission bitmap is not switched
when an immediate exit from L2 to L1 happens right after migration (caused
by a pending event, for example). Unfortunately, in the exact same
situation we still need to have eVMCS mapped so
nested_sync_vmcs12_to_shadow() reflects changes in VMCS12 to eVMCS.
As a band-aid, restore nested_get_evmcs_page() when clearing
KVM_REQ_GET_NESTED_STATE_PAGES in nested_vmx_vmexit(). The 'fix' is far
from being ideal as we can't easily propagate possible failures and even if
we could, this is most likely already too late to do so. The whole
'KVM_REQ_GET_NESTED_STATE_PAGES' idea for mapping eVMCS after migration
seems to be fragile as we diverge too much from the 'native' path when
vmptr loading happens on vmx_set_nested_state(). |
| In the Linux kernel, the following vulnerability has been resolved:
drm/i915: Fix crash in auto_retire
The retire logic uses the 2 lower bits of the pointer to the retire
function to store flags. However, the auto_retire function is not
guaranteed to be aligned to a multiple of 4, which causes crashes as
we jump to the wrong address, for example like this:
2021-04-24T18:03:53.804300Z WARNING kernel: [ 516.876901] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
2021-04-24T18:03:53.804310Z WARNING kernel: [ 516.876906] CPU: 7 PID: 146 Comm: kworker/u16:6 Tainted: G U 5.4.105-13595-g3cd84167b2df #1
2021-04-24T18:03:53.804311Z WARNING kernel: [ 516.876907] Hardware name: Google Volteer2/Volteer2, BIOS Google_Volteer2.13672.76.0 02/22/2021
2021-04-24T18:03:53.804312Z WARNING kernel: [ 516.876911] Workqueue: events_unbound active_work
2021-04-24T18:03:53.804313Z WARNING kernel: [ 516.876914] RIP: 0010:auto_retire+0x1/0x20
2021-04-24T18:03:53.804314Z WARNING kernel: [ 516.876916] Code: e8 01 f2 ff ff eb 02 31 db 48 89 d8 5b 5d c3 0f 1f 44 00 00 55 48 89 e5 f0 ff 87 c8 00 00 00 0f 88 ab 47 4a 00 31 c0 5d c3 0f <1f> 44 00 00 55 48 89 e5 f0 ff 8f c8 00 00 00 0f 88 9a 47 4a 00 74
2021-04-24T18:03:53.804319Z WARNING kernel: [ 516.876918] RSP: 0018:ffff9b4d809fbe38 EFLAGS: 00010286
2021-04-24T18:03:53.804320Z WARNING kernel: [ 516.876919] RAX: 0000000000000007 RBX: ffff927915079600 RCX: 0000000000000007
2021-04-24T18:03:53.804320Z WARNING kernel: [ 516.876921] RDX: ffff9b4d809fbe40 RSI: 0000000000000286 RDI: ffff927915079600
2021-04-24T18:03:53.804321Z WARNING kernel: [ 516.876922] RBP: ffff9b4d809fbe68 R08: 8080808080808080 R09: fefefefefefefeff
2021-04-24T18:03:53.804321Z WARNING kernel: [ 516.876924] R10: 0000000000000010 R11: ffffffff92e44bd8 R12: ffff9279150796a0
2021-04-24T18:03:53.804322Z WARNING kernel: [ 516.876925] R13: ffff92791c368180 R14: ffff927915079640 R15: 000000001c867605
2021-04-24T18:03:53.804323Z WARNING kernel: [ 516.876926] FS: 0000000000000000(0000) GS:ffff92791ffc0000(0000) knlGS:0000000000000000
2021-04-24T18:03:53.804323Z WARNING kernel: [ 516.876928] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
2021-04-24T18:03:53.804324Z WARNING kernel: [ 516.876929] CR2: 0000239514955000 CR3: 00000007f82da001 CR4: 0000000000760ee0
2021-04-24T18:03:53.804325Z WARNING kernel: [ 516.876930] PKRU: 55555554
2021-04-24T18:03:53.804325Z WARNING kernel: [ 516.876931] Call Trace:
2021-04-24T18:03:53.804326Z WARNING kernel: [ 516.876935] __active_retire+0x77/0xcf
2021-04-24T18:03:53.804326Z WARNING kernel: [ 516.876939] process_one_work+0x1da/0x394
2021-04-24T18:03:53.804327Z WARNING kernel: [ 516.876941] worker_thread+0x216/0x375
2021-04-24T18:03:53.804327Z WARNING kernel: [ 516.876944] kthread+0x147/0x156
2021-04-24T18:03:53.804335Z WARNING kernel: [ 516.876946] ? pr_cont_work+0x58/0x58
2021-04-24T18:03:53.804335Z WARNING kernel: [ 516.876948] ? kthread_blkcg+0x2e/0x2e
2021-04-24T18:03:53.804336Z WARNING kernel: [ 516.876950] ret_from_fork+0x1f/0x40
2021-04-24T18:03:53.804336Z WARNING kernel: [ 516.876952] Modules linked in: cdc_mbim cdc_ncm cdc_wdm xt_cgroup rfcomm cmac algif_hash algif_skcipher af_alg xt_MASQUERADE uinput snd_soc_rt5682_sdw snd_soc_rt5682 snd_soc_max98373_sdw snd_soc_max98373 snd_soc_rl6231 regmap_sdw snd_soc_sof_sdw snd_soc_hdac_hdmi snd_soc_dmic snd_hda_codec_hdmi snd_sof_pci snd_sof_intel_hda_common intel_ipu6_psys snd_sof_xtensa_dsp soundwire_intel soundwire_generic_allocation soundwire_cadence snd_sof_intel_hda snd_sof snd_soc_hdac_hda snd_soc_acpi_intel_match snd_soc_acpi snd_hda_ext_core soundwire_bus snd_hda_intel snd_intel_dspcfg snd_hda_codec snd_hwdep snd_hda_core intel_ipu6_isys videobuf2_dma_contig videobuf2_v4l2 videobuf2_common videobuf2_memops mei_hdcp intel_ipu6 ov2740 ov8856 at24 sx9310 dw9768 v4l2_fwnode cros_ec_typec intel_pmc_mux roles acpi_als typec fuse iio_trig_sysfs cros_ec_light_prox cros_ec_lid_angle cros_ec_sensors cros
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
bus: mhi: pci_generic: Remove WQ_MEM_RECLAIM flag from state workqueue
A recent change created a dedicated workqueue for the state-change work
with WQ_HIGHPRI (no strong reason for that) and WQ_MEM_RECLAIM flags,
but the state-change work (mhi_pm_st_worker) does not guarantee forward
progress under memory pressure, and will even wait on various memory
allocations when e.g. creating devices, loading firmware, etc... The
work is then not part of a memory reclaim path...
Moreover, this causes a warning in check_flush_dependency() since we end
up in code that flushes a non-reclaim workqueue:
[ 40.969601] workqueue: WQ_MEM_RECLAIM mhi_hiprio_wq:mhi_pm_st_worker [mhi] is flushing !WQ_MEM_RECLAIM events_highpri:flush_backlog
[ 40.969612] WARNING: CPU: 4 PID: 158 at kernel/workqueue.c:2607 check_flush_dependency+0x11c/0x140
[ 40.969733] Call Trace:
[ 40.969740] __flush_work+0x97/0x1d0
[ 40.969745] ? wake_up_process+0x15/0x20
[ 40.969749] ? insert_work+0x70/0x80
[ 40.969750] ? __queue_work+0x14a/0x3e0
[ 40.969753] flush_work+0x10/0x20
[ 40.969756] rollback_registered_many+0x1c9/0x510
[ 40.969759] unregister_netdevice_queue+0x94/0x120
[ 40.969761] unregister_netdev+0x1d/0x30
[ 40.969765] mhi_net_remove+0x1a/0x40 [mhi_net]
[ 40.969770] mhi_driver_remove+0x124/0x250 [mhi]
[ 40.969776] device_release_driver_internal+0xf0/0x1d0
[ 40.969778] device_release_driver+0x12/0x20
[ 40.969782] bus_remove_device+0xe1/0x150
[ 40.969786] device_del+0x17b/0x3e0
[ 40.969791] mhi_destroy_device+0x9a/0x100 [mhi]
[ 40.969796] ? mhi_unmap_single_use_bb+0x50/0x50 [mhi]
[ 40.969799] device_for_each_child+0x5e/0xa0
[ 40.969804] mhi_pm_st_worker+0x921/0xf50 [mhi] |
| In the Linux kernel, the following vulnerability has been resolved:
irqchip/gic-v3: Do not enable irqs when handling spurious interrups
We triggered the following error while running our 4.19 kernel
with the pseudo-NMI patches backported to it:
[ 14.816231] ------------[ cut here ]------------
[ 14.816231] kernel BUG at irq.c:99!
[ 14.816232] Internal error: Oops - BUG: 0 [#1] SMP
[ 14.816232] Process swapper/0 (pid: 0, stack limit = 0x(____ptrval____))
[ 14.816233] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G O 4.19.95.aarch64 #14
[ 14.816233] Hardware name: evb (DT)
[ 14.816234] pstate: 80400085 (Nzcv daIf +PAN -UAO)
[ 14.816234] pc : asm_nmi_enter+0x94/0x98
[ 14.816235] lr : asm_nmi_enter+0x18/0x98
[ 14.816235] sp : ffff000008003c50
[ 14.816235] pmr_save: 00000070
[ 14.816237] x29: ffff000008003c50 x28: ffff0000095f56c0
[ 14.816238] x27: 0000000000000000 x26: ffff000008004000
[ 14.816239] x25: 00000000015e0000 x24: ffff8008fb916000
[ 14.816240] x23: 0000000020400005 x22: ffff0000080817cc
[ 14.816241] x21: ffff000008003da0 x20: 0000000000000060
[ 14.816242] x19: 00000000000003ff x18: ffffffffffffffff
[ 14.816243] x17: 0000000000000008 x16: 003d090000000000
[ 14.816244] x15: ffff0000095ea6c8 x14: ffff8008fff5ab40
[ 14.816244] x13: ffff8008fff58b9d x12: 0000000000000000
[ 14.816245] x11: ffff000008c8a200 x10: 000000008e31fca5
[ 14.816246] x9 : ffff000008c8a208 x8 : 000000000000000f
[ 14.816247] x7 : 0000000000000004 x6 : ffff8008fff58b9e
[ 14.816248] x5 : 0000000000000000 x4 : 0000000080000000
[ 14.816249] x3 : 0000000000000000 x2 : 0000000080000000
[ 14.816250] x1 : 0000000000120000 x0 : ffff0000095f56c0
[ 14.816251] Call trace:
[ 14.816251] asm_nmi_enter+0x94/0x98
[ 14.816251] el1_irq+0x8c/0x180 (IRQ C)
[ 14.816252] gic_handle_irq+0xbc/0x2e4
[ 14.816252] el1_irq+0xcc/0x180 (IRQ B)
[ 14.816253] arch_timer_handler_virt+0x38/0x58
[ 14.816253] handle_percpu_devid_irq+0x90/0x240
[ 14.816253] generic_handle_irq+0x34/0x50
[ 14.816254] __handle_domain_irq+0x68/0xc0
[ 14.816254] gic_handle_irq+0xf8/0x2e4
[ 14.816255] el1_irq+0xcc/0x180 (IRQ A)
[ 14.816255] arch_cpu_idle+0x34/0x1c8
[ 14.816255] default_idle_call+0x24/0x44
[ 14.816256] do_idle+0x1d0/0x2c8
[ 14.816256] cpu_startup_entry+0x28/0x30
[ 14.816256] rest_init+0xb8/0xc8
[ 14.816257] start_kernel+0x4c8/0x4f4
[ 14.816257] Code: 940587f1 d5384100 b9401001 36a7fd01 (d4210000)
[ 14.816258] Modules linked in: start_dp(O) smeth(O)
[ 15.103092] ---[ end trace 701753956cb14aa8 ]---
[ 15.103093] Kernel panic - not syncing: Fatal exception in interrupt
[ 15.103099] SMP: stopping secondary CPUs
[ 15.103100] Kernel Offset: disabled
[ 15.103100] CPU features: 0x36,a2400218
[ 15.103100] Memory Limit: none
which is cause by a 'BUG_ON(in_nmi())' in nmi_enter().
From the call trace, we can find three interrupts (noted A, B, C above):
interrupt (A) is preempted by (B), which is further interrupted by (C).
Subsequent investigations show that (B) results in nmi_enter() being
called, but that it actually is a spurious interrupt. Furthermore,
interrupts are reenabled in the context of (B), and (C) fires with
NMI priority. We end-up with a nested NMI situation, something
we definitely do not want to (and cannot) handle.
The bug here is that spurious interrupts should never result in any
state change, and we should just return to the interrupted context.
Moving the handling of spurious interrupts as early as possible in
the GICv3 handler fixes this issue.
[maz: rewrote commit message, corrected Fixes: tag] |
| In the Linux kernel, the following vulnerability has been resolved:
riscv/kprobe: fix kernel panic when invoking sys_read traced by kprobe
The execution of sys_read end up hitting a BUG_ON() in __find_get_block
after installing kprobe at sys_read, the BUG message like the following:
[ 65.708663] ------------[ cut here ]------------
[ 65.709987] kernel BUG at fs/buffer.c:1251!
[ 65.711283] Kernel BUG [#1]
[ 65.712032] Modules linked in:
[ 65.712925] CPU: 0 PID: 51 Comm: sh Not tainted 5.12.0-rc4 #1
[ 65.714407] Hardware name: riscv-virtio,qemu (DT)
[ 65.715696] epc : __find_get_block+0x218/0x2c8
[ 65.716835] ra : __getblk_gfp+0x1c/0x4a
[ 65.717831] epc : ffffffe00019f11e ra : ffffffe00019f56a sp : ffffffe002437930
[ 65.719553] gp : ffffffe000f06030 tp : ffffffe0015abc00 t0 : ffffffe00191e038
[ 65.721290] t1 : ffffffe00191e038 t2 : 000000000000000a s0 : ffffffe002437960
[ 65.723051] s1 : ffffffe00160ad00 a0 : ffffffe00160ad00 a1 : 000000000000012a
[ 65.724772] a2 : 0000000000000400 a3 : 0000000000000008 a4 : 0000000000000040
[ 65.726545] a5 : 0000000000000000 a6 : ffffffe00191e000 a7 : 0000000000000000
[ 65.728308] s2 : 000000000000012a s3 : 0000000000000400 s4 : 0000000000000008
[ 65.730049] s5 : 000000000000006c s6 : ffffffe00240f800 s7 : ffffffe000f080a8
[ 65.731802] s8 : 0000000000000001 s9 : 000000000000012a s10: 0000000000000008
[ 65.733516] s11: 0000000000000008 t3 : 00000000000003ff t4 : 000000000000000f
[ 65.734434] t5 : 00000000000003ff t6 : 0000000000040000
[ 65.734613] status: 0000000000000100 badaddr: 0000000000000000 cause: 0000000000000003
[ 65.734901] Call Trace:
[ 65.735076] [<ffffffe00019f11e>] __find_get_block+0x218/0x2c8
[ 65.735417] [<ffffffe00020017a>] __ext4_get_inode_loc+0xb2/0x2f6
[ 65.735618] [<ffffffe000201b6c>] ext4_get_inode_loc+0x3a/0x8a
[ 65.735802] [<ffffffe000203380>] ext4_reserve_inode_write+0x2e/0x8c
[ 65.735999] [<ffffffe00020357a>] __ext4_mark_inode_dirty+0x4c/0x18e
[ 65.736208] [<ffffffe000206bb0>] ext4_dirty_inode+0x46/0x66
[ 65.736387] [<ffffffe000192914>] __mark_inode_dirty+0x12c/0x3da
[ 65.736576] [<ffffffe000180dd2>] touch_atime+0x146/0x150
[ 65.736748] [<ffffffe00010d762>] filemap_read+0x234/0x246
[ 65.736920] [<ffffffe00010d834>] generic_file_read_iter+0xc0/0x114
[ 65.737114] [<ffffffe0001f5d7a>] ext4_file_read_iter+0x42/0xea
[ 65.737310] [<ffffffe000163f2c>] new_sync_read+0xe2/0x15a
[ 65.737483] [<ffffffe000165814>] vfs_read+0xca/0xf2
[ 65.737641] [<ffffffe000165bae>] ksys_read+0x5e/0xc8
[ 65.737816] [<ffffffe000165c26>] sys_read+0xe/0x16
[ 65.737973] [<ffffffe000003972>] ret_from_syscall+0x0/0x2
[ 65.738858] ---[ end trace fe93f985456c935d ]---
A simple reproducer looks like:
echo 'p:myprobe sys_read fd=%a0 buf=%a1 count=%a2' > /sys/kernel/debug/tracing/kprobe_events
echo 1 > /sys/kernel/debug/tracing/events/kprobes/myprobe/enable
cat /sys/kernel/debug/tracing/trace
Here's what happens to hit that BUG_ON():
1) After installing kprobe at entry of sys_read, the first instruction
is replaced by 'ebreak' instruction on riscv64 platform.
2) Once kernel reach the 'ebreak' instruction at the entry of sys_read,
it trap into the riscv breakpoint handler, where it do something to
setup for coming single-step of origin instruction, including backup
the 'sstatus' in pt_regs, followed by disable interrupt during single
stepping via clear 'SIE' bit of 'sstatus' in pt_regs.
3) Then kernel restore to the instruction slot contains two instructions,
one is original instruction at entry of sys_read, the other is 'ebreak'.
Here it trigger a 'Instruction page fault' exception (value at 'scause'
is '0xc'), if PF is not filled into PageTabe for that slot yet.
4) Again kernel trap into page fault exception handler, where it choose
different policy according to the state of running kprobe. Because
afte 2) the state is KPROBE_HIT_SS, so kernel reset the current kp
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
ACPI: GTDT: Don't corrupt interrupt mappings on watchdow probe failure
When failing the driver probe because of invalid firmware properties,
the GTDT driver unmaps the interrupt that it mapped earlier.
However, it never checks whether the mapping of the interrupt actially
succeeded. Even more, should the firmware report an illegal interrupt
number that overlaps with the GIC SGI range, this can result in an
IPI being unmapped, and subsequent fireworks (as reported by Dann
Frazier).
Rework the driver to have a slightly saner behaviour and actually
check whether the interrupt has been mapped before unmapping things. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: always panic when errors=panic is specified
Before commit 014c9caa29d3 ("ext4: make ext4_abort() use
__ext4_error()"), the following series of commands would trigger a
panic:
1. mount /dev/sda -o ro,errors=panic test
2. mount /dev/sda -o remount,abort test
After commit 014c9caa29d3, remounting a file system using the test
mount option "abort" will no longer trigger a panic. This commit will
restore the behaviour immediately before commit 014c9caa29d3.
(However, note that the Linux kernel's behavior has not been
consistent; some previous kernel versions, including 5.4 and 4.19
similarly did not panic after using the mount option "abort".)
This also makes a change to long-standing behaviour; namely, the
following series commands will now cause a panic, when previously it
did not:
1. mount /dev/sda -o ro,errors=panic test
2. echo test > /sys/fs/ext4/sda/trigger_fs_error
However, this makes ext4's behaviour much more consistent, so this is
a good thing. |
| In the Linux kernel, the following vulnerability has been resolved:
io_uring: fix shared sqpoll cancellation hangs
[ 736.982891] INFO: task iou-sqp-4294:4295 blocked for more than 122 seconds.
[ 736.982897] Call Trace:
[ 736.982901] schedule+0x68/0xe0
[ 736.982903] io_uring_cancel_sqpoll+0xdb/0x110
[ 736.982908] io_sqpoll_cancel_cb+0x24/0x30
[ 736.982911] io_run_task_work_head+0x28/0x50
[ 736.982913] io_sq_thread+0x4e3/0x720
We call io_uring_cancel_sqpoll() one by one for each ctx either in
sq_thread() itself or via task works, and it's intended to cancel all
requests of a specified context. However the function uses per-task
counters to track the number of inflight requests, so it counts more
requests than available via currect io_uring ctx and goes to sleep for
them to appear (e.g. from IRQ), that will never happen.
Cancel a bit more than before, i.e. all ctxs that share sqpoll
and continue to use shared counters. Don't forget that we should not
remove ctx from the list before running that task_work sqpoll-cancel,
otherwise the function wouldn't be able to find the context and will
hang. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: dwc3: core: Do core softreset when switch mode
According to the programming guide, to switch mode for DRD controller,
the driver needs to do the following.
To switch from device to host:
1. Reset controller with GCTL.CoreSoftReset
2. Set GCTL.PrtCapDir(host mode)
3. Reset the host with USBCMD.HCRESET
4. Then follow up with the initializing host registers sequence
To switch from host to device:
1. Reset controller with GCTL.CoreSoftReset
2. Set GCTL.PrtCapDir(device mode)
3. Reset the device with DCTL.CSftRst
4. Then follow up with the initializing registers sequence
Currently we're missing step 1) to do GCTL.CoreSoftReset and step 3) of
switching from host to device. John Stult reported a lockup issue seen
with HiKey960 platform without these steps[1]. Similar issue is observed
with Ferry's testing platform[2].
So, apply the required steps along with some fixes to Yu Chen's and John
Stultz's version. The main fixes to their versions are the missing wait
for clocks synchronization before clearing GCTL.CoreSoftReset and only
apply DCTL.CSftRst when switching from host to device.
[1] https://lore.kernel.org/linux-usb/[email protected]/
[2] https://lore.kernel.org/linux-usb/[email protected]/ |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: idxd: fix wq size store permission state
WQ size can only be changed when the device is disabled. Current code
allows change when device is enabled but wq is disabled. Change the check
to detect device state. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nftables: clone set element expression template
memcpy() breaks when using connlimit in set elements. Use
nft_expr_clone() to initialize the connlimit expression list, otherwise
connlimit garbage collector crashes when walking on the list head copy.
[ 493.064656] Workqueue: events_power_efficient nft_rhash_gc [nf_tables]
[ 493.064685] RIP: 0010:find_or_evict+0x5a/0x90 [nf_conncount]
[ 493.064694] Code: 2b 43 40 83 f8 01 77 0d 48 c7 c0 f5 ff ff ff 44 39 63 3c 75 df 83 6d 18 01 48 8b 43 08 48 89 de 48 8b 13 48 8b 3d ee 2f 00 00 <48> 89 42 08 48 89 10 48 b8 00 01 00 00 00 00 ad de 48 89 03 48 83
[ 493.064699] RSP: 0018:ffffc90000417dc0 EFLAGS: 00010297
[ 493.064704] RAX: 0000000000000000 RBX: ffff888134f38410 RCX: 0000000000000000
[ 493.064708] RDX: 0000000000000000 RSI: ffff888134f38410 RDI: ffff888100060cc0
[ 493.064711] RBP: ffff88812ce594a8 R08: ffff888134f38438 R09: 00000000ebb9025c
[ 493.064714] R10: ffffffff8219f838 R11: 0000000000000017 R12: 0000000000000001
[ 493.064718] R13: ffffffff82146740 R14: ffff888134f38410 R15: 0000000000000000
[ 493.064721] FS: 0000000000000000(0000) GS:ffff88840e440000(0000) knlGS:0000000000000000
[ 493.064725] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 493.064729] CR2: 0000000000000008 CR3: 00000001330aa002 CR4: 00000000001706e0
[ 493.064733] Call Trace:
[ 493.064737] nf_conncount_gc_list+0x8f/0x150 [nf_conncount]
[ 493.064746] nft_rhash_gc+0x106/0x390 [nf_tables] |
| In the Linux kernel, the following vulnerability has been resolved:
ch_ktls: Fix kernel panic
Taking page refcount is not ideal and causes kernel panic
sometimes. It's better to take tx_ctx lock for the complete
skb transmit, to avoid page cleanup if ACK received in middle. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Use correct permission flag for mixed signed bounds arithmetic
We forbid adding unknown scalars with mixed signed bounds due to the
spectre v1 masking mitigation. Hence this also needs bypass_spec_v1
flag instead of allow_ptr_leaks. |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: add sanity tests to TCP_QUEUE_SEQ
Qingyu Li reported a syzkaller bug where the repro
changes RCV SEQ _after_ restoring data in the receive queue.
mprotect(0x4aa000, 12288, PROT_READ) = 0
mmap(0x1ffff000, 4096, PROT_NONE, MAP_PRIVATE|MAP_FIXED|MAP_ANONYMOUS, -1, 0) = 0x1ffff000
mmap(0x20000000, 16777216, PROT_READ|PROT_WRITE|PROT_EXEC, MAP_PRIVATE|MAP_FIXED|MAP_ANONYMOUS, -1, 0) = 0x20000000
mmap(0x21000000, 4096, PROT_NONE, MAP_PRIVATE|MAP_FIXED|MAP_ANONYMOUS, -1, 0) = 0x21000000
socket(AF_INET6, SOCK_STREAM, IPPROTO_IP) = 3
setsockopt(3, SOL_TCP, TCP_REPAIR, [1], 4) = 0
connect(3, {sa_family=AF_INET6, sin6_port=htons(0), sin6_flowinfo=htonl(0), inet_pton(AF_INET6, "::1", &sin6_addr), sin6_scope_id=0}, 28) = 0
setsockopt(3, SOL_TCP, TCP_REPAIR_QUEUE, [1], 4) = 0
sendmsg(3, {msg_name=NULL, msg_namelen=0, msg_iov=[{iov_base="0x0000000000000003\0\0", iov_len=20}], msg_iovlen=1, msg_controllen=0, msg_flags=0}, 0) = 20
setsockopt(3, SOL_TCP, TCP_REPAIR, [0], 4) = 0
setsockopt(3, SOL_TCP, TCP_QUEUE_SEQ, [128], 4) = 0
recvfrom(3, NULL, 20, 0, NULL, NULL) = -1 ECONNRESET (Connection reset by peer)
syslog shows:
[ 111.205099] TCP recvmsg seq # bug 2: copied 80, seq 0, rcvnxt 80, fl 0
[ 111.207894] WARNING: CPU: 1 PID: 356 at net/ipv4/tcp.c:2343 tcp_recvmsg_locked+0x90e/0x29a0
This should not be allowed. TCP_QUEUE_SEQ should only be used
when queues are empty.
This patch fixes this case, and the tx path as well. |
| In the Linux kernel, the following vulnerability has been resolved:
media: aspeed: fix clock handling logic
Video engine uses eclk and vclk for its clock sources and its reset
control is coupled with eclk so the current clock enabling sequence works
like below.
Enable eclk
De-assert Video Engine reset
10ms delay
Enable vclk
It introduces improper reset on the Video Engine hardware and eventually
the hardware generates unexpected DMA memory transfers that can corrupt
memory region in random and sporadic patterns. This issue is observed
very rarely on some specific AST2500 SoCs but it causes a critical
kernel panic with making a various shape of signature so it's extremely
hard to debug. Moreover, the issue is observed even when the video
engine is not actively used because udevd turns on the video engine
hardware for a short time to make a query in every boot.
To fix this issue, this commit changes the clock handling logic to make
the reset de-assertion triggered after enabling both eclk and vclk. Also,
it adds clk_unprepare call for a case when probe fails.
clk: ast2600: fix reset settings for eclk and vclk
Video engine reset setting should be coupled with eclk to match it
with the setting for previous Aspeed SoCs which is defined in
clk-aspeed.c since all Aspeed SoCs are sharing a single video engine
driver. Also, reset bit 6 is defined as 'Video Engine' reset in
datasheet so it should be de-asserted when eclk is enabled. This
commit fixes the setting. |
| .NET Framework Denial of Service Vulnerability |
| BitLocker Security Feature Bypass Vulnerability |
