| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid1,raid10: fix bio accounting for split md cloned bios
Use md_cloned_bio() to control bio accounting instead of relying
on r1bio_existed in raid1 or the io_accounting flag in raid10.
The previous logic does not reliably reflect whether a bio is an
md cloned bio. When a failed bio is split and resubmitted via
bio_submit_split_bioset() on the error path, this can lead to either
double accounting for md cloned bios, or missing accounting for bios
returned from bio_submit_split_bioset()
Fix this by using md_cloned_bio() to detect md cloned bios and
skip accounting accordingly. |
| In the Linux kernel, the following vulnerability has been resolved:
raid1: fix nr_pending leak in REQ_ATOMIC bad-block error path
In raid1_write_request(), each per-mirror loop iteration begins by
incrementing rdev->nr_pending. If a REQ_ATOMIC write encounters a
badblock within the requested range, the code jumps to err_handle
without dropping the reference taken for the current mirror.
err_handle's cleanup loop will only decrements for k < i and
r1_bio->bios[k] is non-NULL. The current slot is therefore skipped,
leaving its nr_pending reference leaked permanently. The reference
prevents the rdev from ever being removed, since raid1_remove_conf()
refuses to remove an rdev with nr_pending > 0.
Fix this by calling rdev_dec_pending() before jumping to err_handle. |
| In the Linux kernel, the following vulnerability has been resolved:
liveupdate: fix u-a-f in luo_file_unpreserve_files() and luo_file_finish()
In luo_file_unpreserve_files() and luo_file_finish(), reorder
module_put() and xa_erase() to ensure the file handler module remains
pinned while its operations are being accessed.
Specifically, luo_get_id() dereferences fh->ops->get_id, so the module
reference must be held until after xa_erase() (which calls luo_get_id)
completes.
For luo_file_finish(), this requires moving the module_put() call out of
the luo_file_finish_one() helper and into the main loop of
luo_file_finish() itself. |
| In the Linux kernel, the following vulnerability has been resolved:
ext2: fix ignored return value of generic_write_sync()
Fix ext2_dio_write_iter() to propagate the error returned by
generic_write_sync() instead of silently discarding it, which could
cause write(2) to return success to userspace on O_SYNC/O_DSYNC files
even when the sync failed.
The correct pattern, already used in ext2_dax_write_iter() in the same
file and in ext4, xfs, f2fs among others, is:
if (ret > 0)
ret = generic_write_sync(iocb, ret);
Found by Linux Verification Center (linuxtesting.org) with SVACE.
[JK: Reflect also filemap_write_and_wait() return value] |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix fast commit wait/wake bit mapping on 64-bit
On 64-bit, ext4 dynamic inode states live in the upper half of i_flags,
and ext4_test_inode_state() applies the corresponding +32 offset.
The fast-commit wait and wake paths open-coded the wait key with the raw
EXT4_STATE_* value. Add small helpers for the state wait word and bit,
and use them for the FC_COMMITTING and FC_FLUSHING_DATA waits so the wait
key follows the same mapping as the state helpers. |
| In the Linux kernel, the following vulnerability has been resolved:
fbdev: sm501fb: Fix buffer errors in OF binding code
The code that gets the frame buffer mode from OF has 'use after free',
'buffer overrun' and memory leaks.
info->edid_data isn't free if the probe functions fail or if
pd->def_mode is set.
If both the CRT and PANEL are enabled info->edid_data is used after
being freed and is freed twice.
The string returned by of_get_property(np, "mode", &len) is just
written over either the static "640x480-16@60" or the module parameter
string without any regard for the length (which is most likely longer).
Use kstrump() for the OF mode and free everything before freeing 'info. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: zoned: fix deadlock waiting for ticket during data relocation
When performing data relocation on a zoned filesystem, BTRFS can deadlock
in handle_reserve_tickets(). The relocation process is waiting on a space
reservation ticket that can never be fulfilled, because the relocation
itself is the operation responsible for freeing up that space.
Fix this by introducing a new flush state,
BTRFS_RESERVE_FLUSH_ZONED_RELOCATION, specifically for data chunk
allocation during zoned relocation. Like
BTRFS_RESERVE_FLUSH_FREE_SPACE_INODE, this state uses
priority_reclaim_data_space() instead of the normal flushing path, which
avoids re-entering the relocation code and breaking the deadlock cycle.
In btrfs_alloc_data_chunk_ondemand(), select this new flush state when the
inode belongs to a data relocation root on a zoned filesystem. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix deadlock cloning inline extent when using flushoncommit
In commit b48c980b6a7e ("btrfs: fix deadlock between reflink and
transaction commit when using flushoncommit") a deadlock was fixed
between reflinks and transaction commits when the fs is mounted with the
flushoncommit option. This happened when we had to copy an inline extent's
data to the destination file. However the issue was fixed only for the
case where the destination offset is 0, it missed the case when the offset
is greater than zero.
Fix this by ensuring we get i_size update whenever we copied an inline
extent's data into the destination file.
Syzbot reported this with the following trace:
INFO: task kworker/u8:3:57 blocked for more than 143 seconds.
Not tainted syzkaller #0
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:kworker/u8:3 state:D stack:21600 pid:57 tgid:57 ppid:2 task_flags:0x4208160 flags:0x00080000
Workqueue: writeback wb_workfn (flush-btrfs-129)
Call Trace:
<TASK>
context_switch kernel/sched/core.c:5402 [inline]
__schedule+0x16f9/0x5500 kernel/sched/core.c:7204
__schedule_loop kernel/sched/core.c:7283 [inline]
schedule+0x164/0x360 kernel/sched/core.c:7298
wait_extent_bit fs/btrfs/extent-io-tree.c:905 [inline]
btrfs_lock_extent_bits+0x59c/0x700 fs/btrfs/extent-io-tree.c:2008
btrfs_lock_extent fs/btrfs/extent-io-tree.h:152 [inline]
btrfs_invalidate_folio+0x440/0xc00 fs/btrfs/inode.c:7718
extent_writepage fs/btrfs/extent_io.c:1848 [inline]
extent_write_cache_pages fs/btrfs/extent_io.c:2552 [inline]
btrfs_writepages+0x12f3/0x2410 fs/btrfs/extent_io.c:2684
do_writepages+0x32e/0x550 mm/page-writeback.c:2571
__writeback_single_inode+0x133/0x10e0 fs/fs-writeback.c:1764
writeback_sb_inodes+0x97f/0x1980 fs/fs-writeback.c:2056
wb_writeback+0x445/0xb00 fs/fs-writeback.c:2241
wb_do_writeback fs/fs-writeback.c:2388 [inline]
wb_workfn+0x3fd/0xf20 fs/fs-writeback.c:2428
process_one_work+0x98b/0x1630 kernel/workqueue.c:3318
process_scheduled_works kernel/workqueue.c:3401 [inline]
worker_thread+0xb49/0x1140 kernel/workqueue.c:3482
kthread+0x388/0x470 kernel/kthread.c:436
ret_from_fork+0x514/0xb70 arch/x86/kernel/process.c:158
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245
</TASK>
INFO: task syz.0.145:8523 blocked for more than 143 seconds.
Not tainted syzkaller #0
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:syz.0.145 state:D stack:22752 pid:8523 tgid:8522 ppid:5850 task_flags:0x400140 flags:0x00080002
Call Trace:
<TASK>
context_switch kernel/sched/core.c:5402 [inline]
__schedule+0x16f9/0x5500 kernel/sched/core.c:7204
__schedule_loop kernel/sched/core.c:7283 [inline]
schedule+0x164/0x360 kernel/sched/core.c:7298
wb_wait_for_completion+0x3e8/0x790 fs/fs-writeback.c:227
__writeback_inodes_sb_nr+0x24c/0x2d0 fs/fs-writeback.c:2847
try_to_writeback_inodes_sb+0x9a/0xc0 fs/fs-writeback.c:2895
btrfs_start_delalloc_flush fs/btrfs/transaction.c:2182 [inline]
btrfs_commit_transaction+0x813/0x2fc0 fs/btrfs/transaction.c:2371
btrfs_sync_file+0xdf4/0x1230 fs/btrfs/file.c:1822
generic_write_sync include/linux/fs.h:2663 [inline]
btrfs_do_write_iter+0x6a9/0x840 fs/btrfs/file.c:1473
new_sync_write fs/read_write.c:595 [inline]
vfs_write+0x629/0xba0 fs/read_write.c:688
ksys_write+0x156/0x270 fs/read_write.c:740
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0x15f/0x560 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f5a0bdece59
RSP: 002b:00007f5a0b446028 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 00007f5a0c065fa0 RCX: 00007f5a0bdece59
RDX: 000000000000029f RSI: 0000200000
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btmtk: fix URB leak in alloc_mtk_intr_urb error path
When btmtk_isopkt_pad() fails, the previously allocated URB is not freed,
leaking the urb structure. Add usb_free_urb() before returning the error. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: xilinx: use FIFO occupancy register to determine buffer size
The method the driver uses to determine the size of the FIFO has a
problem. What it currently does is this:
It stops the SPI hardware and writes to the TX FIFO register until TX
FIFO FULL asserts in the status register. But the hardware does not only
have the FIFO, it also has a shift register which can hold a byte. This
can be seen, when writing a byte to the FIFO (while the SPI hardware is
stopped,) the TX FIFO EMPTY is still empty. So, if we have a FIFO size
of 16 for example, the current method returns a 17.
This is a problem, at least when using the driver in irq mode. The same
size determined for the TX FIFO is also assumed for the RX FIFO. When a
SPI transaction wants to write the amount of the FIFO size or more
bytes, the following happens, for example with 16 bytes FIFO size:
The driver stops the SPI hardware and writes 17 bytes to the TX FIFO and
starts the SPI hardware and goes sleep.
The hardware then shifts out 17 bytes (FIFO + shift register) and
simultaneously reads bytes into the RX FIFO, but it only has 16 places,
so it looses one byte. Then TX FIFO empty asserts, wakes the driver
again, which has a fast path and reads 16 bytes from the RX FIFO, but
before reading the last 17th byte (which is lost) it does this:
sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
if (!(sr & XSPI_SR_RX_EMPTY_MASK)) {
xilinx_spi_rx(xspi);
rx_words--;
}
It reads the status register and checks if the RX FIFO is not empty.
But it is empty in our case. So this check spins in a while loop
forever locking the driver.
This patch fixes the logic to determine the FIFO size. |
| In the Linux kernel, the following vulnerability has been resolved:
power: supply: core: fix supplied_from allocations
If dts property power-supplies has multiple values, then accessing to
psy->supplied_from[i-1] in __power_supply_populate_supplied_from will
overrun supplied_from array. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: seq: avoid stale FIFO cells during resize
snd_seq_fifo_resize() still needs to publish the replacement pool
before it waits for FIFO users. A blocking snd_seq_read() holds
f->use_lock while it sleeps, so concurrent senders must be able to
queue to the new pool and wake that reader instead of failing against a
closing old pool.
However, snd_seq_fifo_event_in() duplicates an event before it takes
f->lock, and snd_seq_read() can dequeue a cell and later call
snd_seq_fifo_cell_putback() if copy_to_user() or
snd_seq_expand_var_event() fails. If resize swaps f->pool and detaches
oldhead in between, either path can relink an old-pool cell after the
snapshot. That stale cell sits outside the drained oldhead list, keeps
oldpool->counter elevated, and can leave snd_seq_pool_delete() waiting
for the retired pool to drain.
Keep the existing swap-before-wait ordering in snd_seq_fifo_resize(),
but reject stale cells before any FIFO relink. Revalidate event-in cells
under f->lock and retry them against the published replacement pool, and
free stale putback cells instead of linking them back into the FIFO.
The buggy scenario involves two paths, with each column showing the
order within that path:
resize path: relink path:
1. Allocate newpool. 1. Take f->use_lock.
2. Swap f->pool to newpool and 2. Duplicate or dequeue an old-pool
detach oldhead. cell before oldpool closes.
3. Mark oldpool closing and 3. Reach a later relink point after
wait for FIFO users. resize published newpool.
4. Free oldhead and delete 4. Relink the old-pool cell after
oldpool. resize detached oldhead.
5. Drop f->use_lock.
The reproducer reports a resize ioctl blocked in the expected pool
teardown path:
signal: resize iteration=98 target_pool=4 exceeded 250ms
(elapsed=251ms)
diagnostic: resize_tid=651 wchan=snd_seq_pool_done
diagnostic: resize_tid=651 stack=
snd_seq_pool_done+0x5b/0x140
snd_seq_pool_delete+0x7a/0x90
snd_seq_fifo_resize+0x193/0x1e0
snd_seq_ioctl_set_client_pool+0x214/0x260
snd_seq_ioctl+0x119/0x540
__x64_sys_ioctl+0xd1/0x120
do_syscall_64+0xbb/0x2f0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
A second run with larger pools hit the same target path:
signal: resize iteration=32 target_pool=64 exceeded 250ms
(elapsed=251ms)
diagnostic: resize_tid=663 wchan=snd_seq_pool_done
diagnostic: resize_tid=663 stack=
snd_seq_pool_done+0x5b/0x140
snd_seq_pool_delete+0x7a/0x90
snd_seq_fifo_resize+0x193/0x1e0
snd_seq_ioctl_set_client_pool+0x214/0x260
snd_seq_ioctl+0x119/0x540
__x64_sys_ioctl+0xd1/0x120
do_syscall_64+0xbb/0x2f0
entry_SYSCALL_64_after_hwframe+0x77/0x7f |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix stainfo check in rtw_aes_decrypt
The null-pointer-guard was incorrect, returning _FAIL on valid pointer.
Invert the guard, so it returns _FAIL on invalid pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: magnetometer: ak8975: fix potential kernel stack memory leak
Currently in the AK8975 driver there are four instances where potential
uninitialized kernel stack memory leaks can occur. If
i2c_smbus_read_i2c_block_data_or_emulated() returns a value less than
the size of the buffer, uninitialized bytes are retained in the buffer
and later the buffer is passed on to IIO buffers, potentially leaking
memory to userspace.
Fix this by adding checks whether the return value of the function is
equal to the size of the buffer and subsequently if the value is
lesser than zero to distinguish from a returned error code. |
| In the Linux kernel, the following vulnerability has been resolved:
apparmor: fix NULL pointer dereference in unpack_pdb
pdb->dfa could be NULL if unpack_dfa fails, causing a NULL pointer
dereference. |
| In the Linux kernel, the following vulnerability has been resolved:
apparmor: fail policy unpack on accept2 allocation failure
unpack_pdb() may need to allocate a missing ACCEPT2 table for older policy
data. If that allocation failed, it set an error message but jumped to the
success path, returning a policydb with the required table missing.
Return -ENOMEM through the normal failure path when the ACCEPT2 allocation
fails. Remove the now-unused out label. |
| In the Linux kernel, the following vulnerability has been resolved:
apparmor: release exe file resources on path failure
get_current_exe_path() takes both an exe_file reference and a path
reference before resolving the path name. If aa_path_name() failed, it
returned immediately and leaked both references.
Route the failure through the common cleanup path so fput() and path_put()
always run after the references are acquired. |
| In the Linux kernel, the following vulnerability has been resolved:
ieee802154: fix kernel-infoleak in dgram_recvmsg()
KMSAN reported a kernel-infoleak in move_addr_to_user():
BUG: KMSAN: kernel-infoleak in instrument_copy_to_user
include/linux/instrumented.h:131 [inline]
BUG: KMSAN: kernel-infoleak in _inline_copy_to_user
include/linux/uaccess.h:205 [inline]
BUG: KMSAN: kernel-infoleak in _copy_to_user+0xcc/0x120
lib/usercopy.c:26
instrument_copy_to_user include/linux/instrumented.h:131 [inline]
_inline_copy_to_user include/linux/uaccess.h:205 [inline]
_copy_to_user+0xcc/0x120 lib/usercopy.c:26
copy_to_user include/linux/uaccess.h:236 [inline]
move_addr_to_user+0x2e7/0x440 net/socket.c:302
____sys_recvmsg+0x232/0x610 net/socket.c:2925
...
Uninit was stored to memory at:
ieee802154_addr_to_sa include/net/ieee802154_netdev.h:369 [inline]
dgram_recvmsg+0xa09/0xbe0 net/ieee802154/socket.c:739
The issue occurs because the `pan_id` field of `struct ieee802154_addr`
is left uninitialized when the address mode is `IEEE802154_ADDR_NONE`.
The execution flow is as follows:
1. `__ieee802154_rx_handle_packet()` declares a local `struct
ieee802154_hdr hdr` on the stack.
2. `ieee802154_hdr_pull()` calls `ieee802154_hdr_get_addr()` to parse
the source and destination addresses into this structure.
3. If the address mode is `IEEE802154_ADDR_NONE`,
`ieee802154_hdr_get_addr()` previously only set the `mode` field,
leaving the `pan_id` field containing uninitialized stack memory.
4. This uninitialized `pan_id` is later copied into a `struct
sockaddr_ieee802154` in `dgram_recvmsg()` via `ieee802154_addr_to_sa()`.
5. Finally, `move_addr_to_user()` copies the socket address structure to
user space, leaking the uninitialized bytes.
Fix this by using `memset` to zero out the address structure in
`ieee802154_hdr_get_addr()` when the mode is `IEEE802154_ADDR_NONE`. |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid10: fix writes_pending leak on write request failures
raid10_make_request() acquires a writes_pending reference with
md_write_start() before dispatching write requests. Several failure
paths in raid10_write_request() complete the bio and return without
reaching the normal write completion path, causing the corresponding
md_write_end() to be skipped.
Make raid10_write_request() return a status indicating whether the write
request was successfully queued. This allows raid10_make_request() to
release the writes_pending reference with md_write_end() when a write
request fails. |
| In the Linux kernel, the following vulnerability has been resolved:
tpm_crb: Check ACPI_COMPANION() against NULL during probe
Every platform driver can be forced to match a device that doesn't match
its list of device IDs because of device_match_driver_override(), so
platform drivers that rely on the existence of a device's ACPI companion
object need to verify its presence.
Accordingly, add a requisite ACPI_COMPANION() check against NULL to the
tpm_crb driver. |
