| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: fix Route Information option length validation
rt6_route_rcv() validates the Route Information option (RFC 4191) length
against the prefix length, but both checks are off by one.
rinfo->length is the ND option length in units of 8 octets and it
*includes* the 8-byte option header, so an option carrying N bytes of
prefix has length == 1 + N/8. RFC 4191 section 2.3 requires length 3
when Prefix Length is greater than 64, and 2 or 3 when it is greater
than 0. The code accepts length >= 2 and length >= 1 respectively.
ipv6_addr_prefix() then copies prefix_len/8 bytes out of rinfo->prefix,
so a Router Advertisement with (prefix_len=128, length=2) or
(prefix_len=64, length=1) makes the kernel read up to 8 bytes past the
end of the option. Those bytes end up in the prefix of the route that
gets installed, so they are visible to userspace:
# RA with a Route Information option (prefix_len=128, length=2)
# followed by a source link-layer address option, 01 01 de ad be ef ca fe
$ ip -6 route show
2001:db8:dead:beef:101:dead:beef:cafe via fe80::1234 dev veth0 proto ra
^^^^^^^^^^^^^^^^^^ the next option, read out of bounds
When the Route Information option is the last one in the packet, those
eight bytes come from the skb tail room instead.
Reject the option lengths RFC 4191 does not allow. |
| In the Linux kernel, the following vulnerability has been resolved:
xdp: reject clones that overrun skb_shared_info tailroom
xdpf_clone() clones broadcast copies into a single page and sets
frame_sz to PAGE_SIZE. __xdp_build_skb_from_frame() later treats that
page like a normal XDP frame and expects the usual skb_shared_info
tailroom at the end of the buffer.
The current check only rejects frames whose linear xdp_frame header,
headroom, and packet data exceed PAGE_SIZE. A source frame backed by a
larger allocation can still satisfy that check while extending into the
clone's required shared-info area. When such a clone is converted back
into an skb, build_skb_around() places skb_shared_info over live packet
bytes and later writes can corrupt XDP return metadata.
Reject clones unless their linear area fits inside
SKB_WITH_OVERHEAD(PAGE_SIZE), matching the tailroom requirement already
enforced by the XDP-to-skb conversion path. |
| A server-side request forgery (SSRF) vulnerability was found in AWX's webhook status callback mechanism. When processing GitHub pull request webhooks, AWX extracts the status callback URL (pull_request.statuses_url) from the incoming webhook payload without validating the target host against the expected Git provider. This URL is persisted in job extra variables and later used to send authenticated status updates. A user with admin role on a webhook-enabled job template can read the template's webhook signing key, forge a signed GitHub webhook payload with an arbitrary statuses_url, and cause AWX to POST status updates to an attacker-controlled or internal URL. The status update request includes the configured Git Personal Access Token (PAT) in the Authorization header, resulting in credential leakage to the attacker-specified endpoint. |
| In the Linux kernel, the following vulnerability has been resolved:
ring-buffer: Use current_context for safe per-CPU buffer swap
The ring_buffer_swap_cpu() function currently checks the per-CPU
committing counter to determine if a buffer is actively being written to
before performing the swap. However, there exists a race window where
this check can be bypassed:
ring_buffer_lock_reserve
cpu_buffer = buffer->buffers[cpu]; // cpu_buffer_a
rb_reserve_next_event
rb_start_commit // inc committing
if (unlikely(READ_ONCE(cpu_buffer->buffer) != buffer)) {...}
__rb_reserve_next
rb_move_tail
rb_end_commit(cpu_buffer); // dec committing => 0
/* interrupt hits here, successfully swaps! */
local_inc(&cpu_buffer->committing);
ring_buffer_unlock_commit
cpu_buffer = buffer->buffers[cpu]; // cpu_buffer_b
rb_commit
rb_end_commit
RB_WARN_ON(cpu_buffer, !local_read(&cpu_buffer->committing))
// triggers warning
The committing counter can temporarily drop to 0 during a single write
operation (within rb_move_tail), creating a window where swap can
succeed even though the write is still in progress. This leads to
inconsistent buffer state and triggers the RB_WARN_ON in rb_commit().
Replace the committing counter check with current_context checks, which
are set at the entry of ring_buffer_lock_reserve() and remain valid
throughout the entire write operation, providing a reliable indicator of
buffer busy state during swap. |
| In the Linux kernel, the following vulnerability has been resolved:
ovpn: skip rehash for peers already removed from by_id
ovpn_nl_peer_set_doit() resolves the target peer via
ovpn_peer_get_by_id() before taking ovpn->lock. In the window between
the lookup (which only takes a refcount) and the subsequent
spin_lock_bh(&ovpn->lock), a concurrent OVPN_CMD_PEER_DEL, keepalive
expiry, or socket teardown can take ovpn->lock first, run
ovpn_peer_remove() to unhash the peer from all four tables (by_id,
by_vpn_addr4/6, by_transp_addr) and release the lock. set_doit then
acquires ovpn->lock and calls ovpn_peer_hash_vpn_ip(), which
re-inserts the now-removed peer back into the rehashing tables.
The same race affects the float path: ovpn_peer_endpoints_update()
holds only a refcount and acquires ovpn->lock very late (after async
AEAD decrypt and a netlink notification), then rehashes the peer
in the by_transp_addr table.
The resurrected peer becomes reachable again from the RX lookup
(ovpn_peer_get_by_transp_addr) and the TX VPN-IP lookup, even though
userspace believes it is gone. Once the data-path refcount drops the
peer is freed via call_rcu while the hash entries embedded in it
remain linked, opening a UAF window.
Bail out of the rehash when hash_entry_id is unhashed, mirroring
the sentinel already used by ovpn_peer_remove() to detect the
already-removed state. The check is safe under ovpn->lock, which
serializes every mutation of hash_entry_id, and is a no-op for the
add path because ovpn_peer_add_mp() inserts hash_entry_id before
calling ovpn_peer_hash_vpn_ip(). |
| In the Linux kernel, the following vulnerability has been resolved:
s390/ism: Fix UAF of sba and ieq during ism_dev_exit()
A ism interrupt handler can be active in parallel with ism_dev_exit(),
accessing freed data structures.
No new interrupts will be generated after unregister_ieq(). Drain ongoing
interrupt handlers by free_irq(), before freeing ism data structures. |
| In the Linux kernel, the following vulnerability has been resolved:
vhost-scsi: reject feature changes after endpoint
vhost_scsi_setup_vq_cmds() runs from VHOST_SCSI_SET_ENDPOINT and allocates
each command's protection scatterlist array (prot_sgl) according to the
acknowledged VIRTIO_SCSI_F_T10_PI bit. The command pools are not rebuilt
when VHOST_SET_FEATURES changes that bit later.
Although virtio feature bits must not change after feature negotiation,
vhost_scsi_set_features() currently accepts such a request after the
endpoint is active and updates acked_features. Enabling T10-PI after
endpoint setup therefore leaves prot_sgl NULL while the I/O path follows
the new feature bit.
For a 129-page protection payload, vhost_scsi_mapal() passes the missing
first chunk to sg_alloc_table_chained():
sg_alloc_table_chained(table, 129, first_chunk=NULL,
nents_first_chunk=inline_sg_cnt)
sg_pool_index() then hits:
BUG_ON(nents > SG_CHUNK_SIZE); /* 129 > 128 */
The kernel reported the following call trace and register state:
Call Trace:
<TASK>
? __sg_alloc_table+0x1d8/0x250
? __pfx_vhost_run_work_list+0x10/0x10 [vhost]
sg_alloc_table_chained+0x59/0xf0
? __pfx_sg_pool_alloc+0x10/0x10
? vhost_scsi_calc_sgls.constprop.0+0x43/0x60 [vhost_scsi]
vhost_scsi_handle_vq+0xf02/0x1700 [vhost_scsi]
? __pfx_vhost_scsi_handle_vq+0x10/0x10 [vhost_scsi]
vhost_scsi_handle_kick+0x37/0x50 [vhost_scsi]
vhost_run_work_list+0x8e/0xd0 [vhost]
vhost_task_fn+0xe1/0x210
ret_from_fork+0x348/0x540
</TASK>
RIP: 0010:0x4
CR2 = 0x4
RSP: 0018:ffffc90000dbf940 EFLAGS: 00010202
RAX: ffffffff82396810 RBX: ffff88811dc28b80 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000820 RDI: 0000000000000081
VHOST_F_LOG_ALL is a vhost-specific runtime feature and remains the only
exception.
Reject changes to any feature other than VHOST_F_LOG_ALL while the
endpoint is active. This preserves the existing runtime log toggle while
preventing feature-dependent command resources and data-path state from
becoming inconsistent. Userspace must clear the endpoint before changing
any other negotiated feature and set the endpoint up again afterward. |
| In the Linux kernel, the following vulnerability has been resolved:
ip6_tunnel: clear skb2->cb[] in ip6ip6_err()
ip6ip6_err() clones an outer IPv6 ICMP error skb, pulls it to the
quoted inner IPv6 packet, and then passes the clone to icmpv6_send().
The clone still carries the outer packet's inet6_skb_parm in skb->cb.
If the outer packet had a Home Address Option, IP6CB(skb2)->dsthao
remains non-zero after skb_pull(). icmpv6_send() later calls
mip6_addr_swap(), which uses that stale dsthao offset against the quoted
inner packet. A malformed inner destination-options header can then make
the HAO lookup and address swap run past the end of the quoted packet
and corrupt skb_shared_info.
Clear skb2->cb[] before pulling the quoted inner IPv6 packet so the
reply path does not reuse metadata left by the outer IPv6 stack. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usx2y: bound the hwdep mmap fault offset
snd_us428ctls_vm_fault() turns the faulting page offset into a kernel
address with no bound of any kind:
offset = vmf->pgoff << PAGE_SHIFT;
vaddr = (char *)(...)->us428ctls_sharedmem + offset;
page = virt_to_page(vaddr);
get_page(page);
vmf->page = page;
return 0;
snd_us428ctls_mmap() checks only the length of the mapping, never the
offset, and us428ctls_sharedmem is a single page from
alloc_pages_exact(). For a character device file_mmap_size_max()
returns ULONG_MAX, so the mm layer imposes no ceiling either. Every page
offset above zero resolves to a struct page outside the object, and the
handler installs it into the caller's address space read-write; the vma
is not marked read-only.
The caller picks the page frame with a single mmap() argument and gets
read-write access to a page of kernel memory it does not own; an offset
that lands in an unpopulated vmemmap region oopses instead.
A process that can open the hwdep node of an attached US-X2Y reaches
this after loading the FPGA image through the same node; no capability
check is involved.
On 7.2.0-rc5 (arm64), mmap() with a large offset:
Unable to handle kernel paging request at virtual address fffffdffc45d5ac8
pc : snd_us428ctls_vm_fault+0x68/0x140 [snd_usb_usx2y]
Call trace:
snd_us428ctls_vm_fault+0x68/0x140 [snd_usb_usx2y]
__do_fault
__handle_mm_fault
handle_mm_fault
el0_da
Reject any offset outside the shared region. The pcm hwdep handler in
usx2yhwdeppcm.c computes its address the same way and needs the same
bound.
Discovered by XBOW, triaged by Baul Lee <[email protected]> |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: act_ct: fix sk_buff leak when the header checks reject a packet
tcf_ct_handle_fragments() runs its header sanity checks before handing
anything to the defragmentation engine:
if (family == NFPROTO_IPV4)
err = tcf_ct_ipv4_is_fragment(skb, &frag);
else
err = tcf_ct_ipv6_is_fragment(skb, &frag);
if (err || !frag)
return err;
tcf_ct_ipv4_is_fragment() returns -EINVAL or -ENOMEM;
tcf_ct_ipv6_is_fragment() adds -EPROTO when ipv6_find_hdr() fails. None of
them frees or queues the skb, so on that path the caller still owns it.
tcf_ct_act() however funnels every non-zero return into the
ownership-transfer exit:
err = tcf_ct_handle_fragments(net, skb, family, p->zone, &defrag);
if (err)
goto out_frag;
...
out_frag:
if (err != -EINPROGRESS)
tcf_action_inc_drop_qstats(&c->common);
return TC_ACT_CONSUMED;
TC_ACT_CONSUMED means the action took ownership of the skb, so no caller
frees it - sch_handle_ingress(), sch_handle_egress() and
tcf_qevent_handle() all deliberately skip the free for that verdict. The
skb is therefore orphaned: one sk_buff plus its data buffer is leaked per
malformed packet, unbounded. Note the drop counter is already incremented
for these errors, so the statistics claim a drop that never happens.
Three different ownership states reach out_frag: today - the skb may be
queued by the defrag engine (-EINPROGRESS), already freed by
nf_ct_handle_fragments(), or still owned by us. Tell the caller which of
those it is, and free the packet ourselves in the last case, which
restores the TC_ACT_SHOT behaviour that predated the Fixes: commit.
Reproduced on v7.2-rc6 with a 54-byte frame carrying a 40-byte IPv6
header with nexthdr = 0 (hop-by-hop) and nothing after it, on a
clsact ingress chain with "action ct". kmemleak reports one leaked
232-byte skbuff_head_cache object plus its 704-byte data buffer per
packet; with this patch it reports none. |
| In the Linux kernel, the following vulnerability has been resolved:
vxlan: do not arm the ageing timer on a device that is down
vxlan_changelink() arms vxlan->age_timer whenever the requested ageing
interval differs from the configured one:
if (conf.age_interval != vxlan->cfg.age_interval)
mod_timer(&vxlan->age_timer, jiffies);
There is no netif_running() test, so the timer is armed even on a device
that was never brought up. The only synchronous cancel in the driver is
the timer_delete_sync() in vxlan_stop(), which is .ndo_stop.
netif_close_many() drops devices without IFF_UP before
__dev_close_many() runs, so that cancel is skipped for such a device.
vxlan_setup() sets dev->needs_free_netdev = true and age_timer is a
member of struct vxlan_dev, so free_netdev() releases the allocation the
timer lives in while it is still queued on a timer_base.
expire_timers() unlinks the entry before it loads timer->function, so
the timer core writes through the freed object's list pointers:
BUG: KASAN: slab-use-after-free in __run_timers+0x208/0x654
Write of size 8 at addr ffff00001adace68 by task true/192
__asan_store8+0x84/0xac
__run_timers+0x208/0x654
run_timer_softirq+0x154/0x18c
Allocated by task 189:
alloc_netdev_mqs+0x64/0x720
rtnl_create_link+0x4ac/0x520
rtnl_newlink+0x758/0xd00
Freed by task 191:
netdev_release+0x40/0x58
netdev_run_todo+0x4a4/0x8c0
rtnl_dellink+0x200/0x4e8
The rtnl operations involved are netns-scoped, so an unprivileged user
can perform them in a new user and network namespace.
Arming the timer on a down device never had an effect: vxlan_cleanup()
returns early on !netif_running(), and vxlan_open() arms the timer for
any non-zero interval once the device is brought up. Add the missing
test.
Discovered by XBOW, triaged by Baul Lee <[email protected]> |
| In the Linux kernel, the following vulnerability has been resolved:
ptp: ocp: Fix board ID over-read
The EEPROM board ID is a fixed 13-byte field and is not guaranteed to
contain a NUL terminator. Passing it directly to
devlink_info_version_fixed_put() treats it as a C string and may read
beyond the field.
Format at most OCP_BOARD_ID_LEN bytes into the existing local buffer
before reporting the ID. Use a precision limit because the snprintf()
output size alone does not bound the source string scan. |
| In the Linux kernel, the following vulnerability has been resolved:
vt: add permission check for KDSKBMETA ioctl
KDSKBMETA modifies keyboard meta mode but lacks the !perm check that all
other keyboard setter ioctls in vt_k_ioctl() enforce, allowing a process
to change meta mode on a non-controlling console without authorization. |
| This CVE ID has been rejected or withdrawn by its CVE Numbering Authority. |
| In the Linux kernel, the following vulnerability has been resolved:
vdpa/mlx5: Fix buffer length in create_direct_keys()
We have seen in our CI the following KASAN message:
BUG: KASAN: slab-out-of-bounds in cmd_exec+0x550/0xca0 [mlx5_core]
Read of size 272 at addr 0000000176795020 by task qemu-system-s39/82764
[...]
[<000011388ab3a7a0>] cmd_exec+0x550/0xca0 [mlx5_core]
[<000011388ab3b61c>] mlx5_cmd_exec_cb+0x25c/0x4f0 [mlx5_core]
[<000011388b21e82e>] mlx5_vdpa_exec_async_cmds+0x22e/0x5e0 [mlx5_vdpa]
[<000011388b21fd44>] create_direct_keys+0x954/0xef0 [mlx5_vdpa]
[...]
The buggy address is located 4128 bytes inside of
allocated 4384-byte region [0000000176794000, 0000000176795120)
So in essence we read 16 bytes beyond 4384-byte allocation.
create_direct_keys calculates the pointer and length for in and out
buffers.
The size calculation for in includes the entire structure
size (out + in + mtt[]) but the pointer passed to cmd_exec points only
to the 'in' field, skipping the 'out' field.
This causes mlx5_copy_to_msg() to read beyond the allocated buffer
by sizeof(out) bytes when copying command data.
Properly calculate the input size to match the pointer and allocation size. |
| In the Linux kernel, the following vulnerability has been resolved:
mac802154: fix netdev use-after-free in beacon worker
mac802154_beacon_worker() reads local->beacon_req under RCU and derives
the sub-interface from the request, but then drops the RCU read lock and
continues to use both sdata and the embedded wpan_dev.
mac802154_stop_beacons_locked() cancels only pending beacon work, clears
local->beacon_req and frees the request. A beacon worker that is already
running can therefore continue after interface teardown and dereference
the freed netdev private area.
The scan worker already pins the netdev before leaving RCU. Apply the
same lifetime rule to the beacon worker: take a netdev reference while
the request is still protected by RCU, and release it on all paths that
continue after the reference is acquired. |
| In the Linux kernel, the following vulnerability has been resolved:
misc: fastrpc: take fl->lock when moving mmaps on interrupted invoke
When an invoke is interrupted by a signal,
wait_for_completion_interruptible() returns -ERESTARTSYS and
fastrpc_internal_invoke() moves every buffer from fl->mmaps onto
cctx->invoke_interrupted_mmaps. This list_del()/list_add_tail() walk
runs without holding fl->lock, the lock that serialises fl->mmaps in
fastrpc_req_mmap() and fastrpc_req_munmap() everywhere else.
Take fl->lock around the move, matching every other fl->mmaps accessor. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: bridge: release template ct on non-IP path
A bridge nftables ct zone set rule can attach a conntrack template to
an skb before nf_ct_bridge_pre() sees it. For non-IPv4 and non-IPv6
EtherTypes, nf_ct_bridge_pre() currently overwrites skb->_nfct with
IP_CT_UNTRACKED without releasing the existing template reference.
That makes the per-cpu template, and any temporary templates allocated
for concurrent use, unreachable and leaks memory until the host runs out
of slab.
Reset the skb conntrack state before marking the frame untracked so the
existing template reference is dropped on the non-IP path. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_conntrack: defer invalid log until after unlock
TCP and SCTP conntrack paths can emit invalid-packet logs while ct->lock
is still held.
When invalid logging is routed to nfnetlink_log and conntrack export is
enabled, the log path can re-enter conntrack netlink glue and dump the
same conntrack again. Protocol attribute dumping may take ct->lock, so
logging while holding that lock can deadlock.
Defer the TCP invalid logs by storing only the minimal log context while
ct->lock is held and emitting the log after unlocking. Also make the TCP
timeout-lowering invalid path return whether a log is needed, then emit
that log after unlocking.
Do the same for the SCTP invalid state-transition log that can be reached
while ct->lock is held.
Add a lockdep assertion to nf_ct_l4proto_log_invalid() so future callers
that log invalid conntracks while holding ct->lock are caught outside TCP
and SCTP as well. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: SVM: Serialize accesses to the owner and mirror list with separate lock
Interaction between KVM_CAP_VM_MOVE_ENC_CONTEXT_FROM and
KVM_CAP_VM_COPY_ENC_CONTEXT_FROM can cause two separate issues:
- in sev_migrate_from(), when the destination KVM is a mirror, the mirror
entry is moved from the source's list to the owner's mirror_vms list,
without holding the owner's lock unlike other writers of the owner's
mirror list (sev_vm_copy_enc_context_from(), sev_vm_destroy()).
A concurrent COPY or destroy can race with sev_migrate_from() and
corrupt the list.
- In sev_vm_destroy(), the *owner* is still active and could receive
concurrently a KVM_CAP_VM_MOVE_ENC_CONTEXT_FROM that causes
sev->enc_context_owner to change. In this case the incorrect VM
receives kvm_put_kvm().
The second issue needs particular care because the owner could disappear
altogether (even though the race window is impossibly small) between
reading it and locking it. There is thus no way to perform the checks
under the owner lock without putting struct kvm under SLAB_TYPESAFE_BY_RCU
(which would allow kvm_get_kvm_safe() under RCU critical section).
It is much simpler to just use a global lock, since the critical
sections are so small and the new lock is always a leaf lock. |
