| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: validate default EEPROM firmware size
The default EEPROM firmware is parsed and copied as a full EEPROM
without checking its length. A truncated file can make the driver
read beyond the firmware buffer during variant validation or the
fallback copy.
Reject files shorter than MT7996_EEPROM_SIZE before parsing or
copying the firmware. |
| In the Linux kernel, the following vulnerability has been resolved:
w1: ds28e17: reject an oversize length on an I2C block read
w1_f19_i2c_master_transfer() is the master_xfer for the DS28E17 1-Wire
to I2C bridge. On an I2C_M_RECV_LEN read, it takes the length from the
device. The downstream slave puts a length byte in buf[0]. The driver
then reads that many bytes into buf[1] with w1_f19_i2c_read().
buf[0] is controlled by the device and can be 0 to 255.
w1_f19_i2c_read() only rejects a zero count. The caller buffer is
I2C_SMBUS_BLOCK_MAX + 2, so 34 bytes. A length above 32 makes the read
run past it, up to about 222 bytes out of bounds.
The SMBus core does check buf[0] against I2C_SMBUS_BLOCK_MAX. That
check runs after master_xfer returns. By then the write is already
done. i2c-algo-bit rejects an oversize length before it copies, and
returns -EPROTO.
Reject a length above I2C_SMBUS_BLOCK_MAX at both RECV_LEN sites, the
same way i2c-algo-bit does. |
| In the Linux kernel, the following vulnerability has been resolved:
tpm: tpm_i2c_nuvoton: disable IRQ on wait timeout
i2c_nuvoton_wait_for_stat() enables the IRQ before waiting for the
interrupt handler to report a status change. If the wait times out, or is
interrupted before the handler runs, the function returns without
balancing the enable_irq() call.
Disable the IRQ before leaving the failed wait path. Also preserve an
interrupted wait's original error code instead of converting it to
-ETIMEDOUT inside the helper. |
| In the Linux kernel, the following vulnerability has been resolved:
smack: fix cred UAF in smack_file_send_sigiotask()
When inspecting the credentials of another task, objective credentials
(->real_cred, accessed with __task_cred()) must always be used.
Accessing ->cred on a non-current task is forbidden unless that task is
being created or destroyed; a task is allowed to change its own ->cred
pointer with no synchronization, and changing ->cred should only affect the
current syscall.
smack_file_send_sigiotask() was accessing both sets of credentials: First
tsk->cred, then __task_cred(tsk).
Fix it, always access the objective credentials here.
I have tested that this bug can lead to a KASAN-reported UAF of struct cred
in smack_file_send_sigiotask(), and that this fix prevents the race. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: ISO: fix use-after-free of listener socket in iso_conn_ready
iso_conn_ready() looks up the BIS listener socket with iso_get_sock(),
which takes a reference, and then, without re-checking its state,
creates a child socket from it:
parent = iso_get_sock(hdev, ...);
if (!parent)
return;
lock_sock(parent);
sk = iso_sock_alloc(sock_net(parent), NULL, BTPROTO_ISO, ...);
...
iso_chan_add(conn, sk, parent);
...
release_sock(parent);
sock_put(parent);
If the listener socket is closed concurrently, between iso_get_sock()
and lock_sock(), the reference taken by iso_get_sock() may be the last
one: the close path drops the link-list reference, and once
iso_conn_ready() drops its own reference at the end of the function the
socket is freed. The child socket, however, is already linked to the
freed parent, and a later disconnect of the child runs iso_chan_del()
-> bt_accept_unlink(), which dereferences the dangling parent pointer
into the freed accept queue (a use-after-free). The same dangling
pointer is also dereferenced through parent->***() in
iso_chan_del().
Fix it the same way the connected (non-BIS) path was fixed in commit
0d255e63fcf3 ("Bluetooth: ISO: hold sk properly in iso_conn_ready"):
after taking the socket lock, re-check that the parent is still a
listening, alive socket, and bail out otherwise. |
| In the Linux kernel, the following vulnerability has been resolved:
selinux: reject an unclaimed class value in security_get_classes()
security_get_classes() sizes an array by p_classes.nprim and fills it at
value - 1, so a class value the policy never defines leaves a NULL.
sel_make_classes() passes every entry to sel_make_dir(), reaching the same
d_alloc_name() dereference as the permission array. The class symbol table
is allowed to be sparse (policydb_class_isvalid() exists to absorb that),
but this getter builds its own array straight from the hash table and has
no such predicate.
Fail the lookup when a value went unclaimed instead of handing out the
NULL. Conforming policies define every class they declare and are
unaffected. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/vmwgfx: drop dma_buf reference on foreign-fd prime import
ttm_prime_fd_to_handle() returns -ENOSYS when the imported fd's
dma_buf->ops do not match the ttm_object_device's ops, but does so
without releasing the reference acquired by dma_buf_get(). Any
unprivileged renderD client passing a non-vmwgfx prime fd through the
DRM_VMW_GB_SURFACE_REF{,_EXT} path leaks one dma_buf reference per
call and indefinitely pins the foreign exporter's GEM resources.
Funnel the error path through the existing dma_buf_put() so the
reference is always dropped. |
| In the Linux kernel, the following vulnerability has been resolved:
afs: Fix leak of ungot volume
Fix afs_lookup_volume_rcu() so that it doesn't leak a dying volume if
afs_try_get_volume() fails. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing/mmiotrace: Add NULL check for mmio_trace_array in logging functions
mmio_trace_rw() and mmio_trace_mapping() retrieve mmio_trace_array into
tr and pass it to __trace_mmiotrace_rw() and __trace_mmiotrace_map().
If these functions are invoked while mmio_trace_array is NULL (e.g. before
initialization or after disabled), accessing tr->array_buffer.buffer will
result in a NULL pointer dereference crash.
Fix this by adding an explicit NULL check for tr at the beginning of
__trace_mmiotrace_rw() and __trace_mmiotrace_map(). |
| In the Linux kernel, the following vulnerability has been resolved:
perf sched: Fix register_pid() overflow, strcpy, and BUG_ON
register_pid() has several issues when processing untrusted perf.data:
1. Integer overflow: (pid + 1) * sizeof(struct task_desc *) can wrap
to a small value on 32-bit systems when pid is large (e.g.
0x40000000), causing realloc to return a tiny buffer followed by
out-of-bounds writes in the initialization loop.
2. Heap buffer overflow: strcpy(task->comm, comm) copies the
untrusted comm string into a fixed 20-byte COMM_LEN buffer with
no length check.
3. BUG_ON on allocation failure: perf.data is untrusted input, so
allocation failures should be handled gracefully rather than
killing the process.
4. Realloc of sched->tasks assigned directly back, leaking the old
pointer on failure; nr_tasks incremented before the realloc,
leaving corrupted state on failure.
Cap pid at PID_MAX_LIMIT (4194304, matching the kernel's maximum
on 64-bit), replace strcpy with strlcpy, guard against NULL comm,
replace BUG_ON with NULL returns using safe realloc patterns, and
add NULL checks in callers that dereference the result. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_tables: make nft_object rhltable per table
The nft_object rhltable is global, this allows for accessing objects
that are being dismangled from lookup path by other existing netns.
Given the nft_obj_destroy() releases the object inmediately, this might
lead to use-after-free of these objects that are being released.
Make the existing rhltable per table to address this issue to deal with
with the nft_rcv_nl_event() path too.
Update nft_obj_lookup() to take the table as non-const, otherwise,
compiler complains when passing the objname_ht to rhltable_lookup(). |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: fix BPF_PROG_QUERY OOB write and cgroup backward compat
BPF_PROG_QUERY writes back the 'query.revision' field unconditionally to
userspace. If userspace passes a smaller 'bpf_attr' structure (e.g. 40
bytes, which was the layout before the addition of 'query.revision'),
the kernel performs an out-of-bounds write.
Fix this by propagating the user-provided attribute size 'uattr_size'
down to the cgroup query handlers, and conditionally skipping writing
the revision field to userspace when the provided buffer size is
insufficient.
query.revision in bpf_mprog_query is structurally identical to the
cgroup case: a late tail field, written unconditionally.
But the backward-compat hazard is not the same.
The min-historical-size test is per command, and bpf_mprog_query only
serves attach types that were born with revision in the struct:
- tcx_prog_query -> BPF_TCX_INGRESS/EGRESS
- netkit_prog_query -> BPF_NETKIT_PRIMARY/PEER
tcx, netkit, the revision field, and bpf_mprog_query itself all landed in
the same v6.6 merge window (053c8e1f235d added the mprog query API +
revision; tcx in e420bed02507, netkit in 35dfaad7188c). There has never
been a tcx/netkit BPF_PROG_QUERY userspace that doesn't know about
revision. So for these commands the minimum legitimate struct already
covers offset 56-64 — no old binary can be broken here.
Contrast with cgroup: BPF_PROG_QUERY on cgroup attach types shipped in
2017; revision write-back was bolted on years later (120933984460). That
path has a real population of pre-revision callers. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/nldev: Fix locking when accessing mr->pd
Sashiko points out that, due to rereg_mr, the PD is actually variable and
all the touches in nldev are racy.
Use mr->device instead of mr->pd->device.
Getting the PD restrack ID is more tricky. To avoid disturbing all the
happy paths, add an rdma_restrack_sync() operation which is sort of like
flush_workqueue() or synchronize_irq(): after it returns, all the old
nldev touches to the mr are gone and everything sees the new PD. This
makes it safe to reach into the PD pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
nvme: target: rdma: fix ndev refcount leak on queue connect
nvmet_rdma_queue_connect() calls nvmet_rdma_find_get_device() which
acquires a reference on the returned ndev via kref_get(). On the path
where the host queue backlog is exceeded and the function returns
NVME_SC_CONNECT_CTRL_BUSY, reference of ndev is not released, leaking
the kref.
Fix this by adding a goto to the existing put_device label before the
early return. |
| In the Linux kernel, the following vulnerability has been resolved:
netfs: Fix netfs_read_folio() to wait on writeback
Fix netfs_read_folio() to wait for an ongoing writeback to complete so that
it can trust the dirty flag and whatever is attached to folio->private
(folio->private may get cleaned up by the collector before it clears the
writeback flag). |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: rtw_mlme: add bounds checks before ie_length subtraction
Add guards to ensure ie_length is large enough before subtracting
fixed IE offsets to prevent unsigned integer underflow. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7915: fix use-after-free bugs in mt7915_mac_dump_work()
When the mt7915 pci chip is detaching, the mt7915_crash_data is
released in mt7915_coredump_unregister(). However, the work item
dump_work may still be running or pending, leading to UAF bugs
when the already freed crash_data is dereferenced again in
mt7915_mac_dump_work().
The race condition can occur as follows:
CPU 0 (removal path) | CPU 1 (workqueue)
mt7915_pci_remove() | mt7915_sys_recovery_set()
mt7915_unregister_device() | mt7915_reset()
mt7915_coredump_unregister() | queue_work()
vfree(dev->coredump.crash_data) | mt7915_mac_dump_work()
| crash_data-> // UAF
Fix this by ensuring dump_work is properly canceled before
the crash_data is deallocated. Add cancel_work_sync() in
mt7915_unregister_device() to synchronize with any pending
or executing dump work. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix use-after-free in smb2_open during durable reconnect
In smb2_open, the call to ksmbd_put_durable_fd(fp) drops the reference
to the durable file descriptor early during the durable reconnect
process. If an error occurs subsequently (eg, ksmbd_iov_pin_rsp fails)
or a scavenger accesses the file, it leads to a use-after-free when
accessing fp properties (eg fp->create_time).
Move the single put to the end of the function below err_out2 so fp
stays valid until smb2_open returns. |
| In the Linux kernel, the following vulnerability has been resolved:
ceph: fix BUG_ON in __ceph_build_xattrs_blob() due to stale blob size
The generic/642 test-case can reproduce the kernel crash:
[40243.605254] ------------[ cut here ]------------
[40243.605956] kernel BUG at fs/ceph/xattr.c:918!
[40243.607142] Oops: invalid opcode: 0000 [#1] SMP PTI
[40243.608067] CPU: 7 UID: 0 PID: 498762 Comm: kworker/7:1 Not tainted 7.0.0-rc7+ #3 PREEMPT(full)
[40243.609700] Hardware name: QEMU Ubuntu 25.10 PC v2 (i440FX + PIIX, + 10.1 machine, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
[40243.611820] Workqueue: ceph-msgr ceph_con_workfn
[40243.612715] RIP: 0010:__ceph_build_xattrs_blob+0x1b8/0x1e0
[40243.613731] Code: 0f 84 82 fe ff ff e9 cf 8e 56 ff 48 8d 65 e8 31 c0 5b 41 5c 41 5d 5d 31 d2 31 c9 31 f6 31 ff 45 31 c0 45 31 c9 c3 cc cc cc cc <0f> 0b 4c 8b 62 08 41 8b 85 24 07 00 00 49 83 c4 04 41 89 44 24 fc
[40243.616888] RSP: 0018:ffffcc80c4d4b688 EFLAGS: 00010287
[40243.617773] RAX: 0000000000010026 RBX: 0000000000000001 RCX: 0000000000000000
[40243.618928] RDX: ffff8a773798dee0 RSI: 0000000000000000 RDI: 0000000000000000
[40243.620158] RBP: ffffcc80c4d4b6a0 R08: 0000000000000000 R09: 0000000000000000
[40243.621573] R10: 0000000000000000 R11: 0000000000000000 R12: ffff8a75f3b58000
[40243.622907] R13: ffff8a75f3b58000 R14: 0000000000000080 R15: 000000000000bffd
[40243.624054] FS: 0000000000000000(0000) GS:ffff8a787d1b4000(0000) knlGS:0000000000000000
[40243.625331] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[40243.626269] CR2: 000072f390b623c0 CR3: 000000011c02a003 CR4: 0000000000372ef0
[40243.627408] Call Trace:
[40243.627839] <TASK>
[40243.628188] __prep_cap+0x3fd/0x4a0
[40243.628789] ? do_raw_spin_unlock+0x4e/0xe0
[40243.629474] ceph_check_caps+0x46a/0xc80
[40243.630094] ? __lock_acquire+0x4a2/0x2650
[40243.630773] ? find_held_lock+0x31/0x90
[40243.631347] ? handle_cap_grant+0x79f/0x1060
[40243.632068] ? lock_release+0xd9/0x300
[40243.632696] ? __mutex_unlock_slowpath+0x3e/0x340
[40243.633429] ? lock_release+0xd9/0x300
[40243.634052] handle_cap_grant+0xcf6/0x1060
[40243.634745] ceph_handle_caps+0x122b/0x2110
[40243.635415] mds_dispatch+0x5bd/0x2160
[40243.636034] ? ceph_con_process_message+0x65/0x190
[40243.636828] ? lock_release+0xd9/0x300
[40243.637431] ceph_con_process_message+0x7a/0x190
[40243.638184] ? kfree+0x311/0x4f0
[40243.638749] ? kfree+0x311/0x4f0
[40243.639268] process_message+0x16/0x1a0
[40243.639915] ? sg_free_table+0x39/0x90
[40243.640572] ceph_con_v2_try_read+0xf58/0x2120
[40243.641255] ? lock_acquire+0xc8/0x300
[40243.641863] ceph_con_workfn+0x151/0x820
[40243.642493] process_one_work+0x22f/0x630
[40243.643093] ? process_one_work+0x254/0x630
[40243.643770] worker_thread+0x1e2/0x400
[40243.644332] ? __pfx_worker_thread+0x10/0x10
[40243.645020] kthread+0x109/0x140
[40243.645560] ? __pfx_kthread+0x10/0x10
[40243.646125] ret_from_fork+0x3f8/0x480
[40243.646752] ? __pfx_kthread+0x10/0x10
[40243.647316] ? __pfx_kthread+0x10/0x10
[40243.647919] ret_from_fork_asm+0x1a/0x30
[40243.648556] </TASK>
[40243.648902] Modules linked in: overlay hctr2 libpolyval chacha libchacha adiantum libnh libpoly1305 essiv intel_rapl_msr intel_rapl_common intel_uncore_frequency_common skx_edac_common nfit kvm_intel kvm irqbypass joydev ghash_clmulni_intel aesni_intel rapl input_leds mac_hid psmouse vga16fb serio_raw vgastate floppy i2c_piix4 pata_acpi bochs qemu_fw_cfg i2c_smbus sch_fq_codel rbd dm_crypt msr parport_pc ppdev lp parport efi_pstore
[40243.654766] ---[ end trace 0000000000000000 ]---
Commit d93231a6bc8a ("ceph: prevent a client from exceeding the MDS
maximum xattr size") moved the required_blob_size computation to before
the __build_xattrs() call, introducing a race.
__build_xattrs() releases and reacquires i_ceph_lock during execution.
In that window, handle_cap_grant() may update i_xattrs.blob with a
newer MDS-provided blob and bump i_xattrs.version. When
__bui
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix FSCTL permission bypass by adding a permission check for FSCTL_SET_SPARSE
FSCTL_SET_SPARSE in fsctl_set_sparse() modifies the file's sparse
attribute and saves it through xattr without any permission checks.
This exposes two issues:
1) A client on a read-only share can change the sparse attribute
on files it opened, even though the share is read-only.
Other FSCTL write operations already check
test_tree_conn_flag(work->tcon, KSMBD_TREE_CONN_FLAG_WRITABLE),
but FSCTL_SET_SPARSE does not.
2) Even on writable shares, clients without FILE_WRITE_DATA or
FILE_WRITE_ATTRIBUTES access should not modify the sparse
attribute. Similar handle-level checks exist in other functions
but are missing here.
Add both share-level writable check and per-handle access check.
Use goto out on error to avoid leaking file references. |
