| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
fou: reject omitted FOU_ATTR_IPPROTO on FOU_ENCAP_DIRECT
Commit 7a9bc9e3f423 ("fou: Don't allow 0 for FOU_ATTR_IPPROTO.") added
NLA_POLICY_MIN(NLA_U8, 1) to fou_nl_policy[FOU_ATTR_IPPROTO], which
rejects an explicitly supplied FOU_ATTR_IPPROTO == 0 attribute with
-ERANGE.
However, FOU_ATTR_IPPROTO is an optional netlink attribute. When a user
sends FOU_CMD_ADD with FOU_ATTR_TYPE set to FOU_ENCAP_DIRECT and omits
FOU_ATTR_IPPROTO entirely, nla_policy validation succeeds and
parse_nl_config() leaves cfg->protocol as 0 (from memset(cfg, 0,
sizeof(*cfg))). fou_create() then creates a FOU_ENCAP_DIRECT socket with
fou->protocol == 0.
In fou_udp_recv(), returning -fou->protocol to udp_queue_rcv_one_skb()
triggers IP protocol resubmission when fou->protocol > 0, whereas
returning 0 tells the UDP tunnel layer that the skb was consumed without
freeing it. When fou->protocol == 0, every packet received on the socket
returns 0 from fou_udp_recv() and leaks the sk_buff.
Reject FOU_ENCAP_DIRECT when !cfg->protocol in fou_create() so that
creating a direct encapsulation port without FOU_ATTR_IPPROTO fails with
-EINVAL while leaving FOU_CMD_DEL and FOU_CMD_GET (which share
parse_nl_config()) unaffected.
Tested in QEMU against Linux 7.3.0-rc3 by sending a FOU_CMD_ADD Generic
Netlink request with FOU_ATTR_PORT = 5555 and FOU_ATTR_TYPE =
FOU_ENCAP_DIRECT while omitting FOU_ATTR_IPPROTO. On the unfixed kernel,
FOU_CMD_ADD succeeds (err = 0), FOU_CMD_GET reports fou->type = 1 and
fou->protocol = 0, and sending 4000 UDP packets to 127.0.0.1:5555 leaks
all 4000 sk_buffs (SUnreclaim in /proc/meminfo grows from 41456 kB to
59008 kB, +17552 kB); with this patch applied, FOU_CMD_ADD is rejected
with -EINVAL (-22). |
| In the Linux kernel, the following vulnerability has been resolved:
bna: prevent IOC timer rearm during teardown
bna: prevent IOC timer rearm during teardown
bnad_pci_remove() and the probe disable_ioceth path call
timer_delete_sync() for ioc_timer, sem_timer and hb_timer, but not for
iocpf_timer. bnad_iocpf_timeout() then takes bnad->bna_lock after
free_netdev() has freed the struct bnad.
Deleting iocpf_timer last does not fix this. sem_timer and
iocpf_timer rearm each other: bnad_iocpf_sem_timeout() can arm
iocpf_timer, and bnad_iocpf_timeout() arms sem_timer from
bfa_ioc_hw_sem_get() when the semaphore is busy.
timer_delete_sync() only waits out its own callback.
bnad_ioceth_disable() can time out and leave that callback live.
Shut all four IOC timers down with timer_shutdown_sync() on both
paths, so a later mod_timer() is ignored.
This issue was identified during our ongoing static-analysis research
while reviewing kernel code. |
| In the Linux kernel, the following vulnerability has been resolved:
ata: libata-scsi: bound the ATA passthru sense descriptor writes
When an ATA PASS-THROUGH command to an ATAPI device fails, the sense
buffer holds the device's REQUEST SENSE reply, and
ata_scsi_set_passthru_sense_fields() trusts its additional length
byte, sb[7], when adding the ATA Status Return descriptor. A faulty
or malicious device can use that to make the kernel read and write
past the 96-byte buffer in three ways:
- scsi_sense_desc_find() is passed sb[7] + 8 as the buffer length, so
its clamp against sb[7] does nothing and the walk runs off the end.
- A type-9 descriptor found near the end is filled in unchecked.
- A new descriptor at sb[8 + len] needs len + 22 bytes, not len + 14,
so len 75..82 writes up to 8 bytes past the end.
Reproduced with KASAN under qemu, with the emulated ATAPI REQUEST SENSE
reply patched:
BUG: KASAN: slab-out-of-bounds in scsi_sense_desc_find+0x1a5/0x210
BUG: KASAN: slab-out-of-bounds in ata_scsi_qc_complete+0x1a15/0x1a50
Both are gone with this patch, and a valid descriptor is still filled
in. |
| Heap-based buffer overflow in Windows Print Spooler Components allows an authorized attacker to elevate privileges locally. |
| Photoshop Desktop is affected by an out-of-bounds write vulnerability that could result in arbitrary code execution in the context of the current user. Exploitation of this issue requires user interaction in that a victim must open a malicious file. |
| Photoshop Desktop is affected by a NULL Pointer Dereference vulnerability that could result in an application denial-of-service. An attacker could exploit this vulnerability to crash the application, leading to a denial-of-service condition. Exploitation of this issue requires user interaction in that a victim must open a malicious file. |
| Photoshop Desktop is affected by an Integer Overflow or Wraparound vulnerability that could result in arbitrary code execution in the context of the current user. Exploitation of this issue requires user interaction in that a victim must open a malicious file. |
| Photoshop Desktop is affected by an out-of-bounds write vulnerability that could result in arbitrary code execution in the context of the current user. Exploitation of this issue requires user interaction in that a victim must open a malicious file. |
| Photoshop Desktop is affected by a Heap-based Buffer Overflow vulnerability that could result in arbitrary code execution in the context of the current user. Exploitation of this issue requires user interaction in that a victim must open a malicious file. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: libiscsi_tcp: Check the data direction of a Data-In PDU
The Data-In branch of iscsi_tcp_hdr_dissect() resolves the ITT to a task
and copies the PDU's data segment into that command's scatterlist without
asking whether the command was reading. iscsi_tcp_r2t_rsp() in the same
file does ask, and rejects an R2T for a command that is not DMA_TO_DEVICE.
A target that answers a WRITE command's ITT with a Data-In therefore has
the initiator write target-supplied bytes into the pages that write was
about to send. Those are the caller's own pinned pages for an O_DIRECT
write, and page cache pages for a buffered one.
Observed against a test target that emits one 512-byte Data-In naming a 128
KB write's ITT, after the R2T for that write. With O_DIRECT the caller's
buffer ends up holding 512 bytes of the target's data while pwrite()
returns 131072. Buffered is quieter: pwrite() and fsync() both succeed,
nothing is logged, and reading those blocks back returns the target's bytes
out of the page cache without a command going on the wire.
Check the direction before using the scatterlist, the way the R2T path
already does. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_tables: skip expired catchall elements on insert and delete
nft_setelem_catchall_insert() looks up duplicates with
nft_set_elem_active() only, while nft_set_catchall_lookup() and the
dump path additionally skip expired elements.
Once a catchall element with a timeout expires, this predicate drift
makes it invisible to userspace dumps, yet it still blocks
re-insertion: with NLM_F_EXCL the request fails with -EEXIST, and
without it the request reports success but silently inserts nothing.
The stale entry only goes away when the (user-tunable) gc interval
elapses, so the catchall rule may silently stop matching for an
arbitrarily long time after its first expiration.
The delete path shows the same drift: nft_setelem_catchall_deactivate()
picks the first active-next entry in the catchall list, so with an
expired entry still pending GC it retires the stale entry instead of
the fresh one, and it deactivates an element that userspace no longer
sees instead of failing with -ENOENT.
Align both walks with the lookup and dump predicates: only an element
that is active and not expired counts as a duplicate or delete
candidate, using the per-netns timestamp taken at transaction start,
in line with the set backend .insert/.deactivate and catchall GC sync
paths. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: ip6t_rt: fix zero-address non-strict match out-of-bounds read
rt_mt6_check() permits rules to be configured with rtinfo->addrnr == 0
even when address matching (IP6T_RT_FST_MASK) is requested.
In the IP6T_RT_FST_NSTRICT path, rt_mt6() evaluates packet routing
addresses against rtinfo->addrs[i] and terminates backwards at the bottom
of the loop:
if (ipv6_addr_equal(ap, &rtinfo->addrs[i])) {
i++;
}
if (i == rtinfo->addrnr)
break;
When addrnr is 0, if the first packet address matches rtinfo->addrs[0],
i is incremented to 1. Because i is now strictly greater than addrnr (0),
the loop termination condition (i == rtinfo->addrnr) is bypassed and will
never be satisfied.
If a crafted IPv6 packet contains matching routing addresses, i will
advance past IP6T_RT_HOPS (16). The subsequent call to ipv6_addr_equal()
reads beyond struct ip6t_rt, triggering UBSAN/KASAN out-of-bounds warnings
or kernel panics.
Fix this by:
1. Rejecting rules in rt_mt6_check() where IP6T_RT_FST_MASK is set but
rtinfo->addrnr is zero.
2. In rt_mt6(), moving the termination condition (i < rtinfo->addrnr)
into the for-loop header condition and removing the backwards break
at the end of the loop body. |
| In the Linux kernel, the following vulnerability has been resolved:
net: atl1c: fix soft lockup on out-of-range tpd_cons read
The hardware can report an out-of-range tpd_cons (seen as 0xffff)
while the PCIe link/MAC is resetting. An out-of-range value can
never be reached and the loop below would spin forever. To avoid
a soft lockup treat it as "nothing new to clean" instead.
Reproduced on two machines, same NIC (Qualcomm Atheros AR8151 v2.0,
4-port), triggered by rebooting a Mikrotik CCR2004 PCIe card that
the ports are directly linked to:
- Ubuntu 26.04.1 LTS, kernel 7.0.0-31-generic. The link-flap
precursor, before the lockup was captured with a full trace
elsewhere:
atl1c 0000:05:00.0 enp5s0f0: NETDEV WATCHDOG: CPU: 4: transmit queue 2 timed out 489984 ms
atl1c 0000:05:00.0: MAC state machine can't be idle since disabled for 10ms second
atl1c 0000:05:00.0: atl1c: enp5s0f0 NIC Link is Up<65535 Mbps Full Duplex>
65535 (0xffff) here is the same value tpd_cons reads back once the
loop below gets stuck.
- Proxmox VE, kernel 7.0.14-11-pve. Same NIC/trigger, this time
caught by the soft lockup watchdog with a full stack trace:
watchdog: BUG: soft lockup - CPU#12 stuck for 354s! [napi/eth%d-0:329]
CPU: 12 UID: 0 PID: 329 Comm: napi/eth%d-0 Tainted: P O L 7.0.14-11-pve #1 PREEMPT(lazy)
RIP: 0010:atl1c_clean_tx+0x142/0x2d0 [atl1c]
Call Trace:
<TASK>
__napi_poll+0x32/0x1e0
napi_threaded_poll_loop+0x286/0x2e0
napi_threaded_poll+0xfd/0x140
kthread+0xf7/0x130
ret_from_fork+0x2da/0x3a0
ret_from_fork_asm+0x1a/0x30
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
net: ipconfig: bound DHCP option construction
ic_dhcp_init_options() appends the hostname (option 12), vendor-class
(option 60) and client-ID (option 61) options into the fixed 312-byte
bootp_pkt.exten[] buffer. Only the client-ID branch checked the
remaining space; the hostname and vendor-class writes were unbounded.
A 64-byte hostname together with the maximum 252-byte dhcpclass=
identifier needs 18 + (2 + 64) + (2 + 252) = 338 of the 312 available
bytes even before the terminating END marker, so the vendor-class memcpy
runs past the end of exten[]. With CONFIG_FORTIFY_SOURCE this is
reported as a field-spanning write and, when the kernel is booted with
panic_on_warn=1, aborts boot with a panic.
Route the optional options through a common helper that makes sure the
option, its 2-byte header and the END marker all fit and drops an option
that would not. Configurations with short options keep sending exactly
the same bytes as before. |
| Out-of-bounds read in Windows Routing and Remote Access Service (RRAS) allows an unauthorized attacker to disclose information over a network. |
| Photoshop Desktop is affected by an out-of-bounds write vulnerability that could result in arbitrary code execution in the context of the current user. Exploitation of this issue requires user interaction in that a victim must open a malicious file. |
| libp2p-rust is the official Rust language implementation of the libp2p networking stack. Prior to 0.49.5, Gossipsub GRAFT control-message handling unconditionally adds attacker-supplied topic hashes to connected_peer.topics without confirming that the peer previously subscribed to those topics. A remote unauthenticated peer that can reach a Gossipsub listener can repeatedly send novel GRAFT topics, causing cumulative per-peer memory growth that is not bounded by subscription filters, peer scoring, or per-message size limits. This can exhaust process memory and cause a denial of service. This issue is fixed in version 0.49.5. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: hid-oxp: use cancel_delayed_work_sync() in remove
oxp_hid_remove() uses cancel_delayed_work() for all three delayed work
items. cancel_delayed_work() only dequeues a pending work item without
waiting for a currently executing callback to finish. If any of the
work callbacks (oxp_rgb_queue_fn, oxp_btn_queue_fn, oxp_mcu_init_fn) is
running at the time of removal, the callback continues executing
concurrently with hid_hw_close() and hid_hw_stop(), accessing the HID
device after it has been closed and stopped.
Use cancel_delayed_work_sync() instead to ensure that any in-progress
work callback completes before device teardown proceeds. |
| A flaw was found in curl. When importing HTTP Strict Transport Security (HSTS) cache records, loading a parent domain entry configured to include subdomains before a longer-lived subdomain entry silently drops the subdomain policy. Consequently, once the parent policy expires, curl fails to upgrade subsequent connections for the subdomain to HTTPS and transmits unencrypted requests, allowing a network attacker to intercept sensitive data. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: arm64: Fix AArch32 DBGBXVR<n> handling
The consolidation of the breakpoint and watchpoint register accessors
switched DBGBXVR<n> from trap_bvr() to trap_dbg_wb_reg(). The latter
selects backing storage with demux_wb_reg(), which only handles Op2 values
4 through 7. Since DBGBXVR<n> uses Op2 1, an AArch32 guest access hits
KVM_BUG_ON() and marks the VM dead.
DBGBXVR<n> aliases DBGBVR<n>_EL1[63:32], and its AA32(HI) descriptor
already selects the upper half. Map Op2 1 to dbg_bvr[] alongside Op2 4,
restoring the pre-regression behavior. |
