| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
i40e: add validation for ring_len param
The `ring_len` parameter provided by the virtual function (VF)
is assigned directly to the hardware memory context (HMC) without
any validation.
To address this, introduce an upper boundary check for both Tx and Rx
queue lengths. The maximum number of descriptors supported by the
hardware is 8k-32.
Additionally, enforce alignment constraints: Tx rings must be a multiple
of 8, and Rx rings must be a multiple of 32. |
| In the Linux kernel, the following vulnerability has been resolved:
i40e: fix validation of VF state in get resources
VF state I40E_VF_STATE_ACTIVE is not the only state in which
VF is actually active so it should not be used to determine
if a VF is allowed to obtain resources.
Use I40E_VF_STATE_RESOURCES_LOADED that is set only in
i40e_vc_get_vf_resources_msg() and cleared during reset. |
| In the Linux kernel, the following vulnerability has been resolved:
io_uring: fix incorrect io_kiocb reference in io_link_skb
In io_link_skb function, there is a bug where prev_notif is incorrectly
assigned using 'nd' instead of 'prev_nd'. This causes the context
validation check to compare the current notification with itself instead
of comparing it with the previous notification.
Fix by using the correct prev_nd parameter when obtaining prev_notif. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/amd/pgtbl: Fix possible race while increase page table level
The AMD IOMMU host page table implementation supports dynamic page table levels
(up to 6 levels), starting with a 3-level configuration that expands based on
IOVA address. The kernel maintains a root pointer and current page table level
to enable proper page table walks in alloc_pte()/fetch_pte() operations.
The IOMMU IOVA allocator initially starts with 32-bit address and onces its
exhuasted it switches to 64-bit address (max address is determined based
on IOMMU and device DMA capability). To support larger IOVA, AMD IOMMU
driver increases page table level.
But in unmap path (iommu_v1_unmap_pages()), fetch_pte() reads
pgtable->[root/mode] without lock. So its possible that in exteme corner case,
when increase_address_space() is updating pgtable->[root/mode], fetch_pte()
reads wrong page table level (pgtable->mode). It does compare the value with
level encoded in page table and returns NULL. This will result is
iommu_unmap ops to fail and upper layer may retry/log WARN_ON.
CPU 0 CPU 1
------ ------
map pages unmap pages
alloc_pte() -> increase_address_space() iommu_v1_unmap_pages() -> fetch_pte()
pgtable->root = pte (new root value)
READ pgtable->[mode/root]
Reads new root, old mode
Updates mode (pgtable->mode += 1)
Since Page table level updates are infrequent and already synchronized with a
spinlock, implement seqcount to enable lock-free read operations on the read path. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/slub: avoid accessing metadata when pointer is invalid in object_err()
object_err() reports details of an object for further debugging, such as
the freelist pointer, redzone, etc. However, if the pointer is invalid,
attempting to access object metadata can lead to a crash since it does
not point to a valid object.
One known path to the crash is when alloc_consistency_checks()
determines the pointer to the allocated object is invalid because of a
freelist corruption, and calls object_err() to report it. The debug code
should report and handle the corruption gracefully and not crash in the
process.
In case the pointer is NULL or check_valid_pointer() returns false for
the pointer, only print the pointer value and skip accessing metadata. |
| In the Linux kernel, the following vulnerability has been resolved:
libceph: fix invalid accesses to ceph_connection_v1_info
There is a place where generic code in messenger.c is reading and
another place where it is writing to con->v1 union member without
checking that the union member is active (i.e. msgr1 is in use).
On 64-bit systems, con->v1.auth_retry overlaps with con->v2.out_iter,
so such a read is almost guaranteed to return a bogus value instead of
0 when msgr2 is in use. This ends up being fairly benign because the
side effect is just the invalidation of the authorizer and successive
fetching of new tickets.
con->v1.connect_seq overlaps with con->v2.conn_bufs and the fact that
it's being written to can cause more serious consequences, but luckily
it's not something that happens often. |
| In the Linux kernel, the following vulnerability has been resolved:
net/smc: fix one NULL pointer dereference in smc_ib_is_sg_need_sync()
BUG: kernel NULL pointer dereference, address: 00000000000002ec
PGD 0 P4D 0
Oops: Oops: 0000 [#1] SMP PTI
CPU: 28 UID: 0 PID: 343 Comm: kworker/28:1 Kdump: loaded Tainted: G OE 6.17.0-rc2+ #9 NONE
Tainted: [O]=OOT_MODULE, [E]=UNSIGNED_MODULE
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.15.0-1 04/01/2014
Workqueue: smc_hs_wq smc_listen_work [smc]
RIP: 0010:smc_ib_is_sg_need_sync+0x9e/0xd0 [smc]
...
Call Trace:
<TASK>
smcr_buf_map_link+0x211/0x2a0 [smc]
__smc_buf_create+0x522/0x970 [smc]
smc_buf_create+0x3a/0x110 [smc]
smc_find_rdma_v2_device_serv+0x18f/0x240 [smc]
? smc_vlan_by_tcpsk+0x7e/0xe0 [smc]
smc_listen_find_device+0x1dd/0x2b0 [smc]
smc_listen_work+0x30f/0x580 [smc]
process_one_work+0x18c/0x340
worker_thread+0x242/0x360
kthread+0xe7/0x220
ret_from_fork+0x13a/0x160
ret_from_fork_asm+0x1a/0x30
</TASK>
If the software RoCE device is used, ibdev->dma_device is a null pointer.
As a result, the problem occurs. Null pointer detection is added to
prevent problems. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5: Fix lockdep assertion on sync reset unload event
Fix lockdep assertion triggered during sync reset unload event. When the
sync reset flow is initiated using the devlink reload fw_activate
option, the PF already holds the devlink lock while handling unload
event. In this case, delegate sync reset unload event handling back to
the devlink callback process to avoid double-locking and resolve the
lockdep warning.
Kernel log:
WARNING: CPU: 9 PID: 1578 at devl_assert_locked+0x31/0x40
[...]
Call Trace:
<TASK>
mlx5_unload_one_devl_locked+0x2c/0xc0 [mlx5_core]
mlx5_sync_reset_unload_event+0xaf/0x2f0 [mlx5_core]
process_one_work+0x222/0x640
worker_thread+0x199/0x350
kthread+0x10b/0x230
? __pfx_worker_thread+0x10/0x10
? __pfx_kthread+0x10/0x10
ret_from_fork+0x8e/0x100
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1a/0x30
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm/dpu: Add a null ptr check for dpu_encoder_needs_modeset
The drm_atomic_get_new_connector_state() can return NULL if the
connector is not part of the atomic state. Add a check to prevent
a NULL pointer dereference.
This follows the same pattern used in dpu_encoder_update_topology()
within the same file, which checks for NULL before using conn_state.
Patchwork: https://patchwork.freedesktop.org/patch/665188/ |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/vm: Clear the scratch_pt pointer on error
Avoid triggering a dereference of an error pointer on cleanup in
xe_vm_free_scratch() by clearing any scratch_pt error pointer.
(cherry picked from commit 358ee50ab565f3c8ea32480e9d03127a81ba32f8) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/mediatek: Add error handling for old state CRTC in atomic_disable
Introduce error handling to address an issue where, after a hotplug
event, the cursor continues to update. This situation can lead to a
kernel panic due to accessing the NULL `old_state->crtc`.
E,g.
Unable to handle kernel NULL pointer dereference at virtual address
Call trace:
mtk_crtc_plane_disable+0x24/0x140
mtk_plane_atomic_update+0x8c/0xa8
drm_atomic_helper_commit_planes+0x114/0x2c8
drm_atomic_helper_commit_tail_rpm+0x4c/0x158
commit_tail+0xa0/0x168
drm_atomic_helper_commit+0x110/0x120
drm_atomic_commit+0x8c/0xe0
drm_atomic_helper_update_plane+0xd4/0x128
__setplane_atomic+0xcc/0x110
drm_mode_cursor_common+0x250/0x440
drm_mode_cursor_ioctl+0x44/0x70
drm_ioctl+0x264/0x5d8
__arm64_sys_ioctl+0xd8/0x510
invoke_syscall+0x6c/0xe0
do_el0_svc+0x68/0xe8
el0_svc+0x34/0x60
el0t_64_sync_handler+0x1c/0xf8
el0t_64_sync+0x180/0x188
Adding NULL pointer checks to ensure stability by preventing operations
on an invalid CRTC state. |
| In the Linux kernel, the following vulnerability has been resolved:
NFS: Fix the setting of capabilities when automounting a new filesystem
Capabilities cannot be inherited when we cross into a new filesystem.
They need to be reset to the minimal defaults, and then probed for
again. |
| In the Linux kernel, the following vulnerability has been resolved:
dm: Always split write BIOs to zoned device limits
Any zoned DM target that requires zone append emulation will use the
block layer zone write plugging. In such case, DM target drivers must
not split BIOs using dm_accept_partial_bio() as doing so can potentially
lead to deadlocks with queue freeze operations. Regular write operations
used to emulate zone append operations also cannot be split by the
target driver as that would result in an invalid writen sector value
return using the BIO sector.
In order for zoned DM target drivers to avoid such incorrect BIO
splitting, we must ensure that large BIOs are split before being passed
to the map() function of the target, thus guaranteeing that the
limits for the mapped device are not exceeded.
dm-crypt and dm-flakey are the only target drivers supporting zoned
devices and using dm_accept_partial_bio().
In the case of dm-crypt, this function is used to split BIOs to the
internal max_write_size limit (which will be suppressed in a different
patch). However, since crypt_alloc_buffer() uses a bioset allowing only
up to BIO_MAX_VECS (256) vectors in a BIO. The dm-crypt device
max_segments limit, which is not set and so default to BLK_MAX_SEGMENTS
(128), must thus be respected and write BIOs split accordingly.
In the case of dm-flakey, since zone append emulation is not required,
the block layer zone write plugging is not used and no splitting of BIOs
required.
Modify the function dm_zone_bio_needs_split() to use the block layer
helper function bio_needs_zone_write_plugging() to force a call to
bio_split_to_limits() in dm_split_and_process_bio(). This allows DM
target drivers to avoid using dm_accept_partial_bio() for write
operations on zoned DM devices. |
| In the Linux kernel, the following vulnerability has been resolved:
ftrace: Also allocate and copy hash for reading of filter files
Currently the reader of set_ftrace_filter and set_ftrace_notrace just adds
the pointer to the global tracer hash to its iterator. Unlike the writer
that allocates a copy of the hash, the reader keeps the pointer to the
filter hashes. This is problematic because this pointer is static across
function calls that release the locks that can update the global tracer
hashes. This can cause UAF and similar bugs.
Allocate and copy the hash for reading the filter files like it is done
for the writers. This not only fixes UAF bugs, but also makes the code a
bit simpler as it doesn't have to differentiate when to free the
iterator's hash between writers and readers. |
| In the Linux kernel, the following vulnerability has been resolved:
gve: prevent ethtool ops after shutdown
A crash can occur if an ethtool operation is invoked
after shutdown() is called.
shutdown() is invoked during system shutdown to stop DMA operations
without performing expensive deallocations. It is discouraged to
unregister the netdev in this path, so the device may still be visible
to userspace and kernel helpers.
In gve, shutdown() tears down most internal data structures. If an
ethtool operation is dispatched after shutdown(), it will dereference
freed or NULL pointers, leading to a kernel panic. While graceful
shutdown normally quiesces userspace before invoking the reboot
syscall, forced shutdowns (as observed on GCP VMs) can still trigger
this path.
Fix by calling netif_device_detach() in shutdown().
This marks the device as detached so the ethtool ioctl handler
will skip dispatching operations to the driver. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: increase scan_ies_len for S1G
Currently the S1G capability element is not taken into account
for the scan_ies_len, which leads to a buffer length validation
failure in ieee80211_prep_hw_scan() and subsequent WARN in
__ieee80211_start_scan(). This prevents hw scanning from functioning.
To fix ensure we accommodate for the S1G capability length. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: Fix use-after-free in l2cap_sock_cleanup_listen()
syzbot reported the splat below without a repro.
In the splat, a single thread calling bt_accept_dequeue() freed sk
and touched it after that.
The root cause would be the racy l2cap_sock_cleanup_listen() call
added by the cited commit.
bt_accept_dequeue() is called under lock_sock() except for
l2cap_sock_release().
Two threads could see the same socket during the list iteration
in bt_accept_dequeue():
CPU1 CPU2 (close())
---- ----
sock_hold(sk) sock_hold(sk);
lock_sock(sk) <-- block close()
sock_put(sk)
bt_accept_unlink(sk)
sock_put(sk) <-- refcnt by bt_accept_enqueue()
release_sock(sk)
lock_sock(sk)
sock_put(sk)
bt_accept_unlink(sk)
sock_put(sk) <-- last refcnt
bt_accept_unlink(sk) <-- UAF
Depending on the timing, the other thread could show up in the
"Freed by task" part.
Let's call l2cap_sock_cleanup_listen() under lock_sock() in
l2cap_sock_release().
[0]:
BUG: KASAN: slab-use-after-free in debug_spin_lock_before kernel/locking/spinlock_debug.c:86 [inline]
BUG: KASAN: slab-use-after-free in do_raw_spin_lock+0x26f/0x2b0 kernel/locking/spinlock_debug.c:115
Read of size 4 at addr ffff88803b7eb1c4 by task syz.5.3276/16995
CPU: 3 UID: 0 PID: 16995 Comm: syz.5.3276 Not tainted syzkaller #0 PREEMPT(full)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0x116/0x1f0 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:378 [inline]
print_report+0xcd/0x630 mm/kasan/report.c:482
kasan_report+0xe0/0x110 mm/kasan/report.c:595
debug_spin_lock_before kernel/locking/spinlock_debug.c:86 [inline]
do_raw_spin_lock+0x26f/0x2b0 kernel/locking/spinlock_debug.c:115
spin_lock_bh include/linux/spinlock.h:356 [inline]
release_sock+0x21/0x220 net/core/sock.c:3746
bt_accept_dequeue+0x505/0x600 net/bluetooth/af_bluetooth.c:312
l2cap_sock_cleanup_listen+0x5c/0x2a0 net/bluetooth/l2cap_sock.c:1451
l2cap_sock_release+0x5c/0x210 net/bluetooth/l2cap_sock.c:1425
__sock_release+0xb3/0x270 net/socket.c:649
sock_close+0x1c/0x30 net/socket.c:1439
__fput+0x3ff/0xb70 fs/file_table.c:468
task_work_run+0x14d/0x240 kernel/task_work.c:227
resume_user_mode_work include/linux/resume_user_mode.h:50 [inline]
exit_to_user_mode_loop+0xeb/0x110 kernel/entry/common.c:43
exit_to_user_mode_prepare include/linux/irq-entry-common.h:225 [inline]
syscall_exit_to_user_mode_work include/linux/entry-common.h:175 [inline]
syscall_exit_to_user_mode include/linux/entry-common.h:210 [inline]
do_syscall_64+0x3f6/0x4c0 arch/x86/entry/syscall_64.c:100
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f2accf8ebe9
Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 a8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007ffdb6cb1378 EFLAGS: 00000246 ORIG_RAX: 00000000000001b4
RAX: 0000000000000000 RBX: 00000000000426fb RCX: 00007f2accf8ebe9
RDX: 0000000000000000 RSI: 000000000000001e RDI: 0000000000000003
RBP: 00007f2acd1b7da0 R08: 0000000000000001 R09: 00000012b6cb166f
R10: 0000001b30e20000 R11: 0000000000000246 R12: 00007f2acd1b609c
R13: 00007f2acd1b6090 R14: ffffffffffffffff R15: 00007ffdb6cb1490
</TASK>
Allocated by task 5326:
kasan_save_stack+0x33/0x60 mm/kasan/common.c:47
kasan_save_track+0x14/0x30 mm/kasan/common.c:68
poison_kmalloc_redzone mm/kasan/common.c:388 [inline]
__kasan_kmalloc+0xaa/0xb0 mm/kasan/common.c:405
kasan_kmalloc include/linux/kasan.h:260 [inline]
__do_kmalloc_node mm/slub.c:4365 [inline]
__kmalloc_nopro
---truncated--- |
| This CVE ID has been rejected or withdrawn by its CVE Numbering Authority. |
| This CVE ID has been rejected or withdrawn by its CVE Numbering Authority. |
| This CVE ID has been rejected or withdrawn by its CVE Numbering Authority. |
