| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: SOF: ipc4-topology: Correct the allocation size for bytes controls
The size of the data behind of scontrol->ipc_control_data for bytes
controls is:
[1] sizeof(struct sof_ipc4_control_data) + // kernel only struct
[2] sizeof(struct sof_abi_hdr)) + payload
The max_size specifies the size of [2] and it is coming from topology.
Change the function to take this into account and allocate adequate amount
of memory behind scontrol->ipc_control_data.
With the change we will allocate [1] amount more memory to be able to hold
the full size of data. |
| In the Linux kernel, the following vulnerability has been resolved:
dm-verity: disable recursive forward error correction
There are two problems with the recursive correction:
1. It may cause denial-of-service. In fec_read_bufs, there is a loop that
has 253 iterations. For each iteration, we may call verity_hash_for_block
recursively. There is a limit of 4 nested recursions - that means that
there may be at most 253^4 (4 billion) iterations. Red Hat QE team
actually created an image that pushes dm-verity to this limit - and this
image just makes the udev-worker process get stuck in the 'D' state.
2. It doesn't work. In fec_read_bufs we store data into the variable
"fio->bufs", but fio bufs is shared between recursive invocations, if
"verity_hash_for_block" invoked correction recursively, it would
overwrite partially filled fio->bufs. |
| In the Linux kernel, the following vulnerability has been resolved:
libceph: make decode_pool() more resilient against corrupted osdmaps
If the osdmap is (maliciously) corrupted such that the encoded length
of ceph_pg_pool envelope is less than what is expected for a particular
encoding version, out-of-bounds reads may ensue because the only bounds
check that is there is based on that length value.
This patch adds explicit bounds checks for each field that is decoded
or skipped. |
| In the Linux kernel, the following vulnerability has been resolved:
net: hns3: add VLAN id validation before using
Currently, the VLAN id may be used without validation when
receive a VLAN configuration mailbox from VF. The length of
vlan_del_fail_bmap is BITS_TO_LONGS(VLAN_N_VID). It may cause
out-of-bounds memory access once the VLAN id is bigger than
or equal to VLAN_N_VID.
Therefore, VLAN id needs to be checked to ensure it is within
the range of VLAN_N_VID. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtlwifi: 8192cu: fix tid out of range in rtl92cu_tx_fill_desc()
TID getting from ieee80211_get_tid() might be out of range of array size
of sta_entry->tids[], so check TID is less than MAX_TID_COUNT. Othwerwise,
UBSAN warn:
UBSAN: array-index-out-of-bounds in drivers/net/wireless/realtek/rtlwifi/rtl8192cu/trx.c:514:30
index 10 is out of range for type 'rtl_tid_data [9]' |
| In the Linux kernel, the following vulnerability has been resolved:
e1000: fix OOB in e1000_tbi_should_accept()
In e1000_tbi_should_accept() we read the last byte of the frame via
'data[length - 1]' to evaluate the TBI workaround. If the descriptor-
reported length is zero or larger than the actual RX buffer size, this
read goes out of bounds and can hit unrelated slab objects. The issue
is observed from the NAPI receive path (e1000_clean_rx_irq):
==================================================================
BUG: KASAN: slab-out-of-bounds in e1000_tbi_should_accept+0x610/0x790
Read of size 1 at addr ffff888014114e54 by task sshd/363
CPU: 0 PID: 363 Comm: sshd Not tainted 5.18.0-rc1 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014
Call Trace:
<IRQ>
dump_stack_lvl+0x5a/0x74
print_address_description+0x7b/0x440
print_report+0x101/0x200
kasan_report+0xc1/0xf0
e1000_tbi_should_accept+0x610/0x790
e1000_clean_rx_irq+0xa8c/0x1110
e1000_clean+0xde2/0x3c10
__napi_poll+0x98/0x380
net_rx_action+0x491/0xa20
__do_softirq+0x2c9/0x61d
do_softirq+0xd1/0x120
</IRQ>
<TASK>
__local_bh_enable_ip+0xfe/0x130
ip_finish_output2+0x7d5/0xb00
__ip_queue_xmit+0xe24/0x1ab0
__tcp_transmit_skb+0x1bcb/0x3340
tcp_write_xmit+0x175d/0x6bd0
__tcp_push_pending_frames+0x7b/0x280
tcp_sendmsg_locked+0x2e4f/0x32d0
tcp_sendmsg+0x24/0x40
sock_write_iter+0x322/0x430
vfs_write+0x56c/0xa60
ksys_write+0xd1/0x190
do_syscall_64+0x43/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f511b476b10
Code: 73 01 c3 48 8b 0d 88 d3 2b 00 f7 d8 64 89 01 48 83 c8 ff c3 66 0f 1f 44 00 00 83 3d f9 2b 2c 00 00 75 10 b8 01 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 31 c3 48 83 ec 08 e8 8e 9b 01 00 48 89 04 24
RSP: 002b:00007ffc9211d4e8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000000000004024 RCX: 00007f511b476b10
RDX: 0000000000004024 RSI: 0000559a9385962c RDI: 0000000000000003
RBP: 0000559a9383a400 R08: fffffffffffffff0 R09: 0000000000004f00
R10: 0000000000000070 R11: 0000000000000246 R12: 0000000000000000
R13: 00007ffc9211d57f R14: 0000559a9347bde7 R15: 0000000000000003
</TASK>
Allocated by task 1:
__kasan_krealloc+0x131/0x1c0
krealloc+0x90/0xc0
add_sysfs_param+0xcb/0x8a0
kernel_add_sysfs_param+0x81/0xd4
param_sysfs_builtin+0x138/0x1a6
param_sysfs_init+0x57/0x5b
do_one_initcall+0x104/0x250
do_initcall_level+0x102/0x132
do_initcalls+0x46/0x74
kernel_init_freeable+0x28f/0x393
kernel_init+0x14/0x1a0
ret_from_fork+0x22/0x30
The buggy address belongs to the object at ffff888014114000
which belongs to the cache kmalloc-2k of size 2048
The buggy address is located 1620 bytes to the right of
2048-byte region [ffff888014114000, ffff888014114800]
The buggy address belongs to the physical page:
page:ffffea0000504400 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x14110
head:ffffea0000504400 order:3 compound_mapcount:0 compound_pincount:0
flags: 0x100000000010200(slab|head|node=0|zone=1)
raw: 0100000000010200 0000000000000000 dead000000000001 ffff888013442000
raw: 0000000000000000 0000000000080008 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
==================================================================
This happens because the TBI check unconditionally dereferences the last
byte without validating the reported length first:
u8 last_byte = *(data + length - 1);
Fix by rejecting the frame early if the length is zero, or if it exceeds
adapter->rx_buffer_len. This preserves the TBI workaround semantics for
valid frames and prevents touching memory beyond the RX buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
nvme: nvme-fc: Ensure ->ioerr_work is cancelled in nvme_fc_delete_ctrl()
nvme_fc_delete_assocation() waits for pending I/O to complete before
returning, and an error can cause ->ioerr_work to be queued after
cancel_work_sync() had been called. Move the call to cancel_work_sync() to
be after nvme_fc_delete_association() to ensure ->ioerr_work is not running
when the nvme_fc_ctrl object is freed. Otherwise the following can occur:
[ 1135.911754] list_del corruption, ff2d24c8093f31f8->next is NULL
[ 1135.917705] ------------[ cut here ]------------
[ 1135.922336] kernel BUG at lib/list_debug.c:52!
[ 1135.926784] Oops: invalid opcode: 0000 [#1] SMP NOPTI
[ 1135.931851] CPU: 48 UID: 0 PID: 726 Comm: kworker/u449:23 Kdump: loaded Not tainted 6.12.0 #1 PREEMPT(voluntary)
[ 1135.943490] Hardware name: Dell Inc. PowerEdge R660/0HGTK9, BIOS 2.5.4 01/16/2025
[ 1135.950969] Workqueue: 0x0 (nvme-wq)
[ 1135.954673] RIP: 0010:__list_del_entry_valid_or_report.cold+0xf/0x6f
[ 1135.961041] Code: c7 c7 98 68 72 94 e8 26 45 fe ff 0f 0b 48 c7 c7 70 68 72 94 e8 18 45 fe ff 0f 0b 48 89 fe 48 c7 c7 80 69 72 94 e8 07 45 fe ff <0f> 0b 48 89 d1 48 c7 c7 a0 6a 72 94 48 89 c2 e8 f3 44 fe ff 0f 0b
[ 1135.979788] RSP: 0018:ff579b19482d3e50 EFLAGS: 00010046
[ 1135.985015] RAX: 0000000000000033 RBX: ff2d24c8093f31f0 RCX: 0000000000000000
[ 1135.992148] RDX: 0000000000000000 RSI: ff2d24d6bfa1d0c0 RDI: ff2d24d6bfa1d0c0
[ 1135.999278] RBP: ff2d24c8093f31f8 R08: 0000000000000000 R09: ffffffff951e2b08
[ 1136.006413] R10: ffffffff95122ac8 R11: 0000000000000003 R12: ff2d24c78697c100
[ 1136.013546] R13: fffffffffffffff8 R14: 0000000000000000 R15: ff2d24c78697c0c0
[ 1136.020677] FS: 0000000000000000(0000) GS:ff2d24d6bfa00000(0000) knlGS:0000000000000000
[ 1136.028765] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1136.034510] CR2: 00007fd207f90b80 CR3: 000000163ea22003 CR4: 0000000000f73ef0
[ 1136.041641] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 1136.048776] DR3: 0000000000000000 DR6: 00000000fffe07f0 DR7: 0000000000000400
[ 1136.055910] PKRU: 55555554
[ 1136.058623] Call Trace:
[ 1136.061074] <TASK>
[ 1136.063179] ? show_trace_log_lvl+0x1b0/0x2f0
[ 1136.067540] ? show_trace_log_lvl+0x1b0/0x2f0
[ 1136.071898] ? move_linked_works+0x4a/0xa0
[ 1136.075998] ? __list_del_entry_valid_or_report.cold+0xf/0x6f
[ 1136.081744] ? __die_body.cold+0x8/0x12
[ 1136.085584] ? die+0x2e/0x50
[ 1136.088469] ? do_trap+0xca/0x110
[ 1136.091789] ? do_error_trap+0x65/0x80
[ 1136.095543] ? __list_del_entry_valid_or_report.cold+0xf/0x6f
[ 1136.101289] ? exc_invalid_op+0x50/0x70
[ 1136.105127] ? __list_del_entry_valid_or_report.cold+0xf/0x6f
[ 1136.110874] ? asm_exc_invalid_op+0x1a/0x20
[ 1136.115059] ? __list_del_entry_valid_or_report.cold+0xf/0x6f
[ 1136.120806] move_linked_works+0x4a/0xa0
[ 1136.124733] worker_thread+0x216/0x3a0
[ 1136.128485] ? __pfx_worker_thread+0x10/0x10
[ 1136.132758] kthread+0xfa/0x240
[ 1136.135904] ? __pfx_kthread+0x10/0x10
[ 1136.139657] ret_from_fork+0x31/0x50
[ 1136.143236] ? __pfx_kthread+0x10/0x10
[ 1136.146988] ret_from_fork_asm+0x1a/0x30
[ 1136.150915] </TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: smbdirect: validate data_offset and data_length field of smb_direct_data_transfer
If data_offset and data_length of smb_direct_data_transfer struct are
invalid, out of bounds issue could happen.
This patch validate data_offset and data_length field in recv_done. |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: rtl9300: ensure data length is within supported range
Add an explicit check for the xfer length to 'rtl9300_i2c_config_xfer'
to ensure the data length isn't within the supported range. In
particular a data length of 0 is not supported by the hardware and
causes unintended or destructive behaviour.
This limitation becomes obvious when looking at the register
documentation [1]. 4 bits are reserved for DATA_WIDTH and the value
of these 4 bits is used as N + 1, allowing a data length range of
1 <= len <= 16.
Affected by this is the SMBus Quick Operation which works with a data
length of 0. Passing 0 as the length causes an underflow of the value
due to:
(len - 1) & 0xf
and effectively specifying a transfer length of 16 via the registers.
This causes a 16-byte write operation instead of a Quick Write. For
example, on SFP modules without write-protected EEPROM this soft-bricks
them by overwriting some initial bytes.
For completeness, also add a quirk for the zero length.
[1] https://svanheule.net/realtek/longan/register/i2c_mst1_ctrl2 |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: ti: edma: Fix memory allocation size for queue_priority_map
Fix a critical memory allocation bug in edma_setup_from_hw() where
queue_priority_map was allocated with insufficient memory. The code
declared queue_priority_map as s8 (*)[2] (pointer to array of 2 s8),
but allocated memory using sizeof(s8) instead of the correct size.
This caused out-of-bounds memory writes when accessing:
queue_priority_map[i][0] = i;
queue_priority_map[i][1] = i;
The bug manifested as kernel crashes with "Oops - undefined instruction"
on ARM platforms (BeagleBoard-X15) during EDMA driver probe, as the
memory corruption triggered kernel hardening features on Clang.
Change the allocation to use sizeof(*queue_priority_map) which
automatically gets the correct size for the 2D array structure. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: fix OOB read/write in network-coding decode
batadv_nc_skb_decode_packet() trusts coded_len and checks only against
skb->len. XOR starts at sizeof(struct batadv_unicast_packet), reducing
payload headroom, and the source skb length is not verified, allowing an
out-of-bounds read and a small out-of-bounds write.
Validate that coded_len fits within the payload area of both destination
and source sk_buffs before XORing. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: multitouch: fix slab out-of-bounds access in mt_report_fixup()
A malicious HID device can trigger a slab out-of-bounds during
mt_report_fixup() by passing in report descriptor smaller than
607 bytes. mt_report_fixup() attempts to patch byte offset 607
of the descriptor with 0x25 by first checking if byte offset
607 is 0x15 however it lacks bounds checks to verify if the
descriptor is big enough before conducting this check. Fix
this bug by ensuring the descriptor size is at least 608
bytes before accessing it.
Below is the KASAN splat after the out of bounds access happens:
[ 13.671954] ==================================================================
[ 13.672667] BUG: KASAN: slab-out-of-bounds in mt_report_fixup+0x103/0x110
[ 13.673297] Read of size 1 at addr ffff888103df39df by task kworker/0:1/10
[ 13.673297]
[ 13.673297] CPU: 0 UID: 0 PID: 10 Comm: kworker/0:1 Not tainted 6.15.0-00005-gec5d573d83f4-dirty #3
[ 13.673297] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.2-debian-1.16.2-1 04/04
[ 13.673297] Call Trace:
[ 13.673297] <TASK>
[ 13.673297] dump_stack_lvl+0x5f/0x80
[ 13.673297] print_report+0xd1/0x660
[ 13.673297] kasan_report+0xe5/0x120
[ 13.673297] __asan_report_load1_noabort+0x18/0x20
[ 13.673297] mt_report_fixup+0x103/0x110
[ 13.673297] hid_open_report+0x1ef/0x810
[ 13.673297] mt_probe+0x422/0x960
[ 13.673297] hid_device_probe+0x2e2/0x6f0
[ 13.673297] really_probe+0x1c6/0x6b0
[ 13.673297] __driver_probe_device+0x24f/0x310
[ 13.673297] driver_probe_device+0x4e/0x220
[ 13.673297] __device_attach_driver+0x169/0x320
[ 13.673297] bus_for_each_drv+0x11d/0x1b0
[ 13.673297] __device_attach+0x1b8/0x3e0
[ 13.673297] device_initial_probe+0x12/0x20
[ 13.673297] bus_probe_device+0x13d/0x180
[ 13.673297] device_add+0xe3a/0x1670
[ 13.673297] hid_add_device+0x31d/0xa40
[...] |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: ad7173: fix channels index for syscalib_mode
Fix the index used to look up the channel when accessing the
syscalib_mode attribute. The address field is a 0-based index (same
as scan_index) that it used to access the channel in the
ad7173_channels array throughout the driver. The channels field, on
the other hand, may not match the address field depending on the
channel configuration specified in the device tree and could result
in an out-of-bounds access. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath12k: Decrement TID on RX peer frag setup error handling
Currently, TID is not decremented before peer cleanup, during error
handling path of ath12k_dp_rx_peer_frag_setup(). This could lead to
out-of-bounds access in peer->rx_tid[].
Hence, add a decrement operation for TID, before peer cleanup to
ensures proper cleanup and prevents out-of-bounds access issues when
the RX peer frag setup fails.
Found during code review. Compile tested only. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath12k: Correct tid cleanup when tid setup fails
Currently, if any error occurs during ath12k_dp_rx_peer_tid_setup(),
the tid value is already incremented, even though the corresponding
TID is not actually allocated. Proceed to
ath12k_dp_rx_peer_tid_delete() starting from unallocated tid,
which might leads to freeing unallocated TID and cause potential
crash or out-of-bounds access.
Hence, fix by correctly decrementing tid before cleanup to match only
the successfully allocated TIDs.
Also, remove tid-- from failure case of ath12k_dp_rx_peer_frag_setup(),
as decrementing the tid before cleanup in loop will take care of this.
Compile tested only. |
| In the Linux kernel, the following vulnerability has been resolved:
media: venus: Add a check for packet size after reading from shared memory
Add a check to ensure that the packet size does not exceed the number of
available words after reading the packet header from shared memory. This
ensures that the size provided by the firmware is safe to process and
prevent potential out-of-bounds memory access. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Limit access to parser->buffer when trace_get_user failed
When the length of the string written to set_ftrace_filter exceeds
FTRACE_BUFF_MAX, the following KASAN alarm will be triggered:
BUG: KASAN: slab-out-of-bounds in strsep+0x18c/0x1b0
Read of size 1 at addr ffff0000d00bd5ba by task ash/165
CPU: 1 UID: 0 PID: 165 Comm: ash Not tainted 6.16.0-g6bcdbd62bd56-dirty
Hardware name: linux,dummy-virt (DT)
Call trace:
show_stack+0x34/0x50 (C)
dump_stack_lvl+0xa0/0x158
print_address_description.constprop.0+0x88/0x398
print_report+0xb0/0x280
kasan_report+0xa4/0xf0
__asan_report_load1_noabort+0x20/0x30
strsep+0x18c/0x1b0
ftrace_process_regex.isra.0+0x100/0x2d8
ftrace_regex_release+0x484/0x618
__fput+0x364/0xa58
____fput+0x28/0x40
task_work_run+0x154/0x278
do_notify_resume+0x1f0/0x220
el0_svc+0xec/0xf0
el0t_64_sync_handler+0xa0/0xe8
el0t_64_sync+0x1ac/0x1b0
The reason is that trace_get_user will fail when processing a string
longer than FTRACE_BUFF_MAX, but not set the end of parser->buffer to 0.
Then an OOB access will be triggered in ftrace_regex_release->
ftrace_process_regex->strsep->strpbrk. We can solve this problem by
limiting access to parser->buffer when trace_get_user failed. |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: rtl9300: Fix out-of-bounds bug in rtl9300_i2c_smbus_xfer
The data->block[0] variable comes from user. Without proper check,
the variable may be very large to cause an out-of-bounds bug.
Fix this bug by checking the value of data->block[0] first.
1. commit 39244cc75482 ("i2c: ismt: Fix an out-of-bounds bug in
ismt_access()")
2. commit 92fbb6d1296f ("i2c: xgene-slimpro: Fix out-of-bounds bug in
xgene_slimpro_i2c_xfer()") |
| In the Linux kernel, the following vulnerability has been resolved:
smb3: fix for slab out of bounds on mount to ksmbd
With KASAN enabled, it is possible to get a slab out of bounds
during mount to ksmbd due to missing check in parse_server_interfaces()
(see below):
BUG: KASAN: slab-out-of-bounds in
parse_server_interfaces+0x14ee/0x1880 [cifs]
Read of size 4 at addr ffff8881433dba98 by task mount/9827
CPU: 5 UID: 0 PID: 9827 Comm: mount Tainted: G
OE 6.16.0-rc2-kasan #2 PREEMPT(voluntary)
Tainted: [O]=OOT_MODULE, [E]=UNSIGNED_MODULE
Hardware name: Dell Inc. Precision Tower 3620/0MWYPT,
BIOS 2.13.1 06/14/2019
Call Trace:
<TASK>
dump_stack_lvl+0x9f/0xf0
print_report+0xd1/0x670
__virt_addr_valid+0x22c/0x430
? parse_server_interfaces+0x14ee/0x1880 [cifs]
? kasan_complete_mode_report_info+0x2a/0x1f0
? parse_server_interfaces+0x14ee/0x1880 [cifs]
kasan_report+0xd6/0x110
parse_server_interfaces+0x14ee/0x1880 [cifs]
__asan_report_load_n_noabort+0x13/0x20
parse_server_interfaces+0x14ee/0x1880 [cifs]
? __pfx_parse_server_interfaces+0x10/0x10 [cifs]
? trace_hardirqs_on+0x51/0x60
SMB3_request_interfaces+0x1ad/0x3f0 [cifs]
? __pfx_SMB3_request_interfaces+0x10/0x10 [cifs]
? SMB2_tcon+0x23c/0x15d0 [cifs]
smb3_qfs_tcon+0x173/0x2b0 [cifs]
? __pfx_smb3_qfs_tcon+0x10/0x10 [cifs]
? cifs_get_tcon+0x105d/0x2120 [cifs]
? do_raw_spin_unlock+0x5d/0x200
? cifs_get_tcon+0x105d/0x2120 [cifs]
? __pfx_smb3_qfs_tcon+0x10/0x10 [cifs]
cifs_mount_get_tcon+0x369/0xb90 [cifs]
? dfs_cache_find+0xe7/0x150 [cifs]
dfs_mount_share+0x985/0x2970 [cifs]
? check_path.constprop.0+0x28/0x50
? save_trace+0x54/0x370
? __pfx_dfs_mount_share+0x10/0x10 [cifs]
? __lock_acquire+0xb82/0x2ba0
? __kasan_check_write+0x18/0x20
cifs_mount+0xbc/0x9e0 [cifs]
? __pfx_cifs_mount+0x10/0x10 [cifs]
? do_raw_spin_unlock+0x5d/0x200
? cifs_setup_cifs_sb+0x29d/0x810 [cifs]
cifs_smb3_do_mount+0x263/0x1990 [cifs] |
| In the Linux kernel, the following vulnerability has been resolved:
hfs: fix slab-out-of-bounds in hfs_bnode_read()
This patch introduces is_bnode_offset_valid() method that checks
the requested offset value. Also, it introduces
check_and_correct_requested_length() method that checks and
correct the requested length (if it is necessary). These methods
are used in hfs_bnode_read(), hfs_bnode_write(), hfs_bnode_clear(),
hfs_bnode_copy(), and hfs_bnode_move() with the goal to prevent
the access out of allocated memory and triggering the crash. |
